ECS4510 Series Web Management Guide-R03
Table Of Contents
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Using the Web Interface
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Displaying Memory Utilization
- Stacking
- Resetting the System
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA (Authentication, Authorization and Accounting)
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Setting a Time Range
- Showing TCAM Utilization
- Setting the ACL Name and Type
- Configuring a Standard IPv4 ACL
- Configuring an Extended IPv4 ACL
- Configuring a Standard IPv6 ACL
- Configuring an Extended IPv6 ACL
- Configuring a MAC ACL
- Configuring an ARP ACL
- Binding a Port to an Access Control List
- Configuring ACL Mirroring
- Showing ACL Hardware Counters
- ARP Inspection
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- IPv4 Source Guard
- IPv6 Source Guard
- DHCP Snooping
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Power over Ethernet
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Setting Community Access Strings
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Switch Clustering
- Ethernet Ring Protection Switching
- Connectivity Fault Management
- Configuring Global Settings for CFM
- Configuring Interfaces for CFM
- Configuring CFM Maintenance Domains
- Configuring CFM Maintenance Associations
- Configuring Maintenance End Points
- Configuring Remote Maintenance End Points
- Transmitting Link Trace Messages
- Transmitting Loop Back Messages
- Transmitting Delay-Measure Requests
- Displaying Local MEPs
- Displaying Details for Local MEPs
- Displaying Local MIPs
- Displaying Remote MEPs
- Displaying Details for Remote MEPs
- Displaying the Link Trace Cache
- Displaying Fault Notification Settings
- Displaying Continuity Check Errors
- OAM Configuration
- UDLD Configuration
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query for IPv4)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering IGMP Query Packets and Multicast Data
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Multicast VLAN Registration for IPv4
- Multicast VLAN Registration for IPv6
- IP Configuration
- IP Services
- General IP Routing
- Unicast Routing
- Overview
- Configuring the Routing Information Protocol
- Configuring General Protocol Settings
- Clearing Entries from the Routing Table
- Specifying Network Interfaces
- Specifying Passive Interfaces
- Specifying Static Neighbors
- Configuring Route Redistribution
- Specifying an Administrative Distance
- Configuring Network Interfaces for RIP
- Displaying RIP Interface Settings
- Displaying Peer Router Information
- Resetting RIP Statistics
- Appendices
- Glossary
- Index
Chapter 2
| Using the Web Interface
Navigating the Web Browser Interface
– 68 –
Snooping 370
Configure Global Enables DHCP snooping globally, MAC-address verification,
information option; and sets the information policy
372
Configure VLAN Enables DHCP snooping on a VLAN 374
Configure Interface Sets the trust mode for an interface 375
Show Information Displays the DHCP Snooping binding information 376
Dynamic Provision Enables dynamic provisioning via DHCP 632
PPPoE Intermediate Agent Point-to-Point Protocol over Ethernet Intermediate Agent 633
Configure Global Enables PPPoE IA on the switch, sets access node identifier, sets generic
error message
633
Configure Interface Enables PPPoE IA on an interface, sets trust status, enables vendor tag
stripping, sets circuit ID and remote ID
635
Show Statistics Shows statistics on PPPoE IA protocol messages 637
Multicast 529
IGMP Snooping 530
General Enables multicast filtering; configures parameters for multicast
snooping
532
Multicast Router 536
Add Static Multicast Router Assigns ports that are attached to a neighboring multicast router 536
Show Static Multicast Router Displays ports statically configured as attached to a neighboring
multicast router
536
Show Current Multicast Router Displays ports attached to a neighboring multicast router, either
through static or dynamic configuration
536
IGMP Member 538
Add Static Member Statically assigns multicast addresses to the selected VLAN 538
Show Static Member Shows multicast addresses statically configured on the selected VLAN 538
Interface 540
Configure VLAN Configures IGMP snooping per VLAN interface 540
Show VLAN Information Shows IGMP snooping settings per VLAN interface 540
Configure Port Configures the interface to drop IGMP query packets or all multicast
data packets
546
Configure Trunk Configures the interface to drop IGMP query packets or all multicast
data packets
546
Forwarding Entry Displays the current multicast groups learned through IGMP Snooping 546
Filter 551
Configure General Enables IGMP filtering for the switch 552
Configure Profile 552
Add Adds IGMP filter profile; and sets access mode 552
Table 4: Switch Main Menu (Continued)
Menu Description Page