Web Management Guide-R03
Table Of Contents
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Displaying Memory Utilization
- Resetting the System
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA Authorization and Accounting
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Setting A Time Range
- Showing TCAM Utilization
- Setting the ACL Name and Type
- Configuring a Standard IPv4 ACL
- Configuring an Extended IPv4 ACL
- Configuring a Standard IPv6 ACL
- Configuring an Extended IPv6 ACL
- Configuring a MAC ACL
- Configuring an ARP ACL
- Binding a Port to an Access Control List
- Configuring ACL Mirroring
- Showing ACL Hardware Counters
- ARP Inspection
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- IP Source Guard
- DHCP Snooping
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Power over Ethernet
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Setting Community Access Strings
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Switch Clustering
- IP Configuration
- IP Services
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering Multicast Data at Interfaces
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Multicast VLAN Registration
- Basic Management Tasks
- Appendices
- Glossary
- Index
Chapter 9
| Class of Service
Layer 2 Queue Settings
– 215 –
the switch services each queue before moving on to the next queue. This
prevents the head-of-line blocking that can occur with strict priority queuing.
◆ If Strict and WRR mode is selected, a combination of strict and weighted service
is used as specified for each queue. The queues assigned to use strict priority
should be specified using the Strict Mode field parameter.
◆ A weight can be assigned to each of the weighted queues (and thereby to the
corresponding traffic priorities). This weight sets the frequency at which each
queue is polled for service, and subsequently affects the response time for
software applications assigned a specific priority value.
Service time is shared at the egress ports by defining scheduling weights for
WRR, or the queuing mode that uses a combination of strict and weighted
queuing. Service time is allocated to each queue by calculating a precise
number of bytes per second that will be serviced on each round.
◆ The specified queue mode applies to all interfaces.
Parameters
These parameters are displayed:
◆ Queue Mode
■
Strict – Services the egress queues in sequential order, transmitting all
traffic in the higher priority queues before servicing lower priority queues.
This ensures that the highest priority packets are always serviced first,
ahead of all other traffic.
■
WRR – Weighted Round-Robin shares bandwidth at the egress ports by
using scheduling weights, and servicing each queue in a round-robin
fashion. (This is the default setting.)
■
Strict and WRR – Uses strict or weighted service as specified for each
queue.
◆ Queue ID – The ID of the priority queue. (Range: 0-7)
◆ Strict Mode – If “Strict and WRR” mode is selected, then a combination of strict
and weighted service is used as specified for each queue. Use this parameter to
specify the queues assigned to use strict priority when using the strict-
weighted queuing mode. (Default: Disabled)
◆ Weight – Sets a weight for each queue which is used by the WRR scheduler.
(Range: 1-255; Default: Weights 1, 2, 4, 6, 8, 10, 12 and 14 are assigned to
queues 0 - 7 respectively)