Web Management Guide-R03
Table Of Contents
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Displaying Memory Utilization
- Resetting the System
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA Authorization and Accounting
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Setting A Time Range
- Showing TCAM Utilization
- Setting the ACL Name and Type
- Configuring a Standard IPv4 ACL
- Configuring an Extended IPv4 ACL
- Configuring a Standard IPv6 ACL
- Configuring an Extended IPv6 ACL
- Configuring a MAC ACL
- Configuring an ARP ACL
- Binding a Port to an Access Control List
- Configuring ACL Mirroring
- Showing ACL Hardware Counters
- ARP Inspection
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- IP Source Guard
- DHCP Snooping
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Power over Ethernet
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Setting Community Access Strings
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Switch Clustering
- IP Configuration
- IP Services
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering Multicast Data at Interfaces
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Multicast VLAN Registration
- Basic Management Tasks
- Appendices
- Glossary
- Index
Chapter 4
| Interface Configuration
Port Configuration
– 103 –
RSPAN uplink ports are enabled on the switch, 802.1X cannot be enabled
globally.
■
Port Security – If port security is enabled on any port, that port cannot be
set as an RSPAN uplink port, even though it can still be configured as an
RSPAN source or destination port. Also, when a port is configured as an
RSPAN uplink port, port security cannot be enabled on that port.
Parameters
These parameters are displayed:
◆ Session – A number identifying this RSPAN session. (Range: 1-2)
Only two mirror sessions are allowed, including both local and remote
mirroring. If local mirroring is enabled (see page 99), then there is only one
session available for RSPAN.
◆ Operation Status – Indicates whether or not RSPAN is currently functioning.
◆ Switch Role – Specifies the role this switch performs in mirroring traffic.
■
None – This switch will not participate in RSPAN.
■
Source - Specifies this device as the source of remotely mirrored traffic.
■
Intermediate - Specifies this device as an intermediate switch,
transparently passing mirrored traffic from one or more sources to one or
more destinations.
■
Destination - Specifies this device as a switch configured with a
destination port which is to receive mirrored traffic for this session.
◆ Remote VLAN – The VLAN to which traffic mirrored from the source port will
be flooded. The VLAN specified in this field must first be reserved for the RSPAN
application using the VLAN > Static page (see page 138).
◆ Uplink Port – A port on any switch participating in RSPAN through which
mirrored traffic is passed on to or received from the RSPAN VLAN.
Only one uplink port can be configured on a source switch, but there is no
limitation on the number of uplink ports
1
configured on an intermediate or
destination switch.
Only destination and uplink ports will be assigned by the switch as members of
the RSPAN VLAN. Ports cannot be manually assigned to an RSPAN VLAN
through the VLAN > Static page. Nor can GVRP dynamically add port members
to an RSPAN VLAN. Also, note that the VLAN > Static (Show) page will not
display any members for an RSPAN VLAN, but will only show configured RSPAN
VLAN identifiers.
◆ Type – Specifies the traffic type to be mirrored remotely. (Options: Rx, Tx, Both)