Web Management Guide-R03
Table Of Contents
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Displaying Memory Utilization
- Resetting the System
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA Authorization and Accounting
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Setting A Time Range
- Showing TCAM Utilization
- Setting the ACL Name and Type
- Configuring a Standard IPv4 ACL
- Configuring an Extended IPv4 ACL
- Configuring a Standard IPv6 ACL
- Configuring an Extended IPv6 ACL
- Configuring a MAC ACL
- Configuring an ARP ACL
- Binding a Port to an Access Control List
- Configuring ACL Mirroring
- Showing ACL Hardware Counters
- ARP Inspection
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- IP Source Guard
- DHCP Snooping
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Power over Ethernet
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Setting Community Access Strings
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Switch Clustering
- IP Configuration
- IP Services
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering Multicast Data at Interfaces
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Multicast VLAN Registration
- Basic Management Tasks
- Appendices
- Glossary
- Index
Chapter 16
| Multicast Filtering
Layer 2 IGMP (Snooping and Query)
– 470 –
Configuring IGMP
Snooping and Query
Parameters
Use the Multicast > IGMP Snooping > General page to configure the switch to
forward multicast traffic intelligently. Based on the IGMP query and report
messages, the switch forwards multicast traffic only to the ports that request it. This
prevents the switch from broadcasting the traffic to all ports and possibly
disrupting network performance.
Command Usage
◆ IGMP Snooping – This switch can passively snoop on IGMP Query and Report
packets transferred between IP multicast routers/switches and IP multicast host
groups to identify the IP multicast group members. It simply monitors the IGMP
packets passing through it, picks out the group registration information, and
configures the multicast filters accordingly.
Note:
If unknown multicast traffic enters a VLAN which has been configured with a
router port, the traffic is forwarded to that port. However, if no router port exists on
the VLAN, the traffic is dropped if unregistered data flooding is disabled (default
behavior), or flooded throughout the VLAN if unregistered data flooding is enabled
(see “Unregistered Data Flooding” in the Command Attributes section).
◆ IGMP Querier – A router, or multicast-enabled switch, can periodically ask their
hosts if they want to receive multicast traffic. If there is more than one router/
switch on the LAN performing IP multicasting, one of these devices is elected
“querier” and assumes the role of querying the LAN for group members. It then
propagates the service requests on to any upstream multicast switch/router to
ensure that it will continue to receive the multicast service.
Note:
Multicast routers use this information from IGMP snooping and query
reports, along with a multicast routing protocol such as DVMRP or PIM, to support
IP multicasting across the Internet.
Parameters
These parameters are displayed:
◆ IGMP Snooping Status – When enabled, the switch will monitor network
traffic to determine which hosts want to receive multicast traffic. This is referred
to as IGMP Snooping. (Default: Disabled)
When IGMP snooping is enabled globally, the per VLAN interface settings for
IGMP snooping take precedence (see “Setting IGMP Snooping Status
per Interface” on page 478).
When IGMP snooping is disabled globally, snooping can still be configured per
VLAN interface, but the interface settings will not take effect until snooping is
re-enabled globally.
◆ Proxy Reporting Status – Enables IGMP Snooping with Proxy Reporting.
(Default: Disabled)