Web Management Guide-R03
Table Of Contents
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Displaying Memory Utilization
- Resetting the System
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA Authorization and Accounting
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Setting A Time Range
- Showing TCAM Utilization
- Setting the ACL Name and Type
- Configuring a Standard IPv4 ACL
- Configuring an Extended IPv4 ACL
- Configuring a Standard IPv6 ACL
- Configuring an Extended IPv6 ACL
- Configuring a MAC ACL
- Configuring an ARP ACL
- Binding a Port to an Access Control List
- Configuring ACL Mirroring
- Showing ACL Hardware Counters
- ARP Inspection
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- IP Source Guard
- DHCP Snooping
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Power over Ethernet
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Setting Community Access Strings
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Switch Clustering
- IP Configuration
- IP Services
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering Multicast Data at Interfaces
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Multicast VLAN Registration
- Basic Management Tasks
- Appendices
- Glossary
- Index
Chapter 4
| Interface Configuration
Port Configuration
– 102 –
◆ Configuration Guidelines
Take the following step to configure an RSPAN session:
1. Use the VLAN Static List (see “Configuring VLAN Groups” on page 138) to
reserve a VLAN for use by RSPAN (marking the “Remote VLAN” field on this
page. (Default VLAN 1 is prohibited.)
2. Set up the source switch on the RSPAN configuration page by specifying the
mirror session, the switch’s role (Source), the RSPAN VLAN, and the uplink port
1
.
Then specify the source port(s), and the traffic type to monitor (Rx, Tx or Both).
3. Set up all intermediate switches on the RSPAN configuration page, entering the
mirror session, the switch’s role (Intermediate), the RSPAN VLAN, and the uplink
port(s).
4. Set up the destination switch on the RSPAN configuration page by specifying
the mirror session, the switch’s role (Destination), the destination port
1
,
whether or not the traffic exiting this port will be tagged or untagged, and the
RSPAN VLAN. Then specify each uplink port where the mirrored traffic is being
received.
◆ RSPAN Limitations
The following limitations apply to the use of RSPAN on this switch:
■
RSPAN Ports – Only ports can be configured as an RSPAN source,
destination, or uplink; static and dynamic trunks are not allowed. A port can
only be configured as one type of RSPAN interface – source, destination, or
uplink. Also, note that the source port and destination port cannot be
configured on the same switch.
■
Local/Remote Mirror – The destination of a local mirror session (created on
the Interface > Port > Mirror page) cannot be used as the destination for
RSPAN traffic.
■
Spanning Tree – If the spanning tree is disabled, BPDUs will not be flooded
onto the RSPAN VLAN.
■
MAC address learning is not supported on RSPAN uplink ports when RSPAN
is enabled on the switch. Therefore, even if spanning tree is enabled after
RSPAN has been configured, MAC address learning will still not be re-
started on the RSPAN uplink ports.
■
IEEE 802.1X – RSPAN and 802.1X are mutually exclusive functions. When
802.1X is enabled globally, RSPAN uplink ports cannot be configured, even
though RSPAN source and destination ports can still be configured. When
1. Only 802.1Q trunk or hybrid (i.e., general use) ports can be configured as an RSPAN
uplink or destination ports – access ports are not allowed (see “Adding Static Members to
VLANs” on page 140).