Web Management Guide-R01
Table Of Contents
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Using the Web Interface
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Configuring CPU Guard
- Displaying Memory Utilization
- Resetting the System
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA (Authentication, Authorization and Accounting)
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- DHCP Snooping
- DHCPv6 Snooping
- ND Snooping
- IPv4 Source Guard
- IPv6 Source Guard
- ARP Inspection
- Application Filter
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting Community Access Strings
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Switch Clustering
- Setting a Time Range
- Ethernet Ring Protection Switching
- OAM Configuration
- UDLD Configuration
- LBD Configuration
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query for IPv4)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering IGMP Packets on an Interface
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Configuring MLD Snooping and Query Parameters
- Setting Immediate Leave Status for MLD Snooping per Interface
- Specifying Static Interfaces for an IPv6 Multicast Router
- Assigning Interfaces to IPv6 Multicast Services
- Filtering MLD Query Packets on an Interface
- Showing MLD Snooping Groups and Source List
- Displaying MLD Snooping Statistics
- Filtering and Throttling MLD Groups
- Multicast VLAN Registration for IPv4
- IP Tools
- IP Configuration
- General IP Routing
- IP Services
- Appendices
Chapter 18
| IP Services
Configuring the PPPoE Intermediate Agent
– 651 –
By default, the parameters for DHCPv6 option 59/60 are not carried by the reply
sent from the DHCPv6 server. To ask for a DHCPv6 reply with option 59/60, the
client can inform the server that it is interested in option 59/60 by sending a
DHCPv6 information request.
Parameters
These parameters are displayed:
◆ Dynamic Provision via DHCPv6 Status – Enables dynamic provisioning via
DHCP. (Default: Disabled)
Web Interface
To enable dynamic provisioning via DHCPv6:
1. Click IP Service, DHCPv6, Dynamic Provision.
2. Mark the Enable box if dynamic provisioning is configured on the DHCP
deamon, and required for bootup.
3. Click Apply.
Figure 439: Enabling Dynamic Provisioning via DHCPv6
Configuring the PPPoE Intermediate Agent
This section describes how to configure the PPPoE Intermediate Agent (PPPoE IA)
relay parameters required for passing authentication messages between a client
and broadband remote access servers.
Configuring PPPoE IA
Global Settings
Use the IP Service > PPPoE Intermediate Agent (Configure Global) page to enable
the PPPoE IA on the switch, set the access node identifier, and set the generic error
message.
Command Usage
When PPPoE IA is enabled, the switch inserts a tag identifying itself as a PPPoE IA
residing between the attached client requesting network access and the ports
connected to broadband remote access servers (BRAS). The switch extracts access-
loop information from the client’s PPPoE Active Discovery Request, and forwards
this information to all trusted ports (designated on the Configure Interface page).
The BRAS detects the presence of the subscriber’s circuit-ID tag inserted by the