Web Management Guide-R01
Table Of Contents
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Using the Web Interface
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Configuring CPU Guard
- Displaying Memory Utilization
- Resetting the System
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA (Authentication, Authorization and Accounting)
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- DHCP Snooping
- DHCPv6 Snooping
- ND Snooping
- IPv4 Source Guard
- IPv6 Source Guard
- ARP Inspection
- Application Filter
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting Community Access Strings
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Switch Clustering
- Setting a Time Range
- Ethernet Ring Protection Switching
- OAM Configuration
- UDLD Configuration
- LBD Configuration
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query for IPv4)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering IGMP Packets on an Interface
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Configuring MLD Snooping and Query Parameters
- Setting Immediate Leave Status for MLD Snooping per Interface
- Specifying Static Interfaces for an IPv6 Multicast Router
- Assigning Interfaces to IPv6 Multicast Services
- Filtering MLD Query Packets on an Interface
- Showing MLD Snooping Groups and Source List
- Displaying MLD Snooping Statistics
- Filtering and Throttling MLD Groups
- Multicast VLAN Registration for IPv4
- IP Tools
- IP Configuration
- General IP Routing
- IP Services
- Appendices
Chapter 14
| Multicast Filtering
Multicast VLAN Registration for IPv4
– 574 –
membership for MVR receiver ports cannot be set to access mode (see “Adding
Static Members to VLANs” on page 161).
◆ One or more interfaces may be configured as MVR source ports. A source port is
able to both receive and send data for configured MVR groups or for groups
which have been statically assigned (see “Assigning Static MVR Multicast
Groups to Interfaces” on page 576).
All source ports must belong to the MVR VLAN.
Subscribers should not be directly connected to source ports.
◆ Immediate leave applies only to receiver ports. When enabled, the receiver port
is immediately removed from the multicast group identified in the leave
message. When immediate leave is disabled, the switch follows the standard
rules by sending a query message to the receiver port and waiting for a
response to determine if there are any remaining subscribers for that multicast
group before removing the port from the group list.
■
Using immediate leave can speed up leave latency, but should only be
enabled on a port attached to one multicast subscriber to avoid disrupting
services to other group members attached to the same interface.
■
Immediate leave does not apply to multicast groups which have been
statically assigned to a port.
Parameters
These parameters are displayed:
◆ Domain ID – An independent multicast domain. (Range: 1-5)
◆ Port/Trunk – Interface identifier.
◆ Type – The following interface types are supported:
■
Source – An uplink port that can send and receive multicast data for the
groups assigned to the MVR VLAN. Note that the source port must be
manually configured as a member of the MVR VLAN (see “Adding Static
Members to VLANs” on page 161).
■
Receiver – A subscriber port that can receive multicast data sent through
the MVR VLAN. Any port configured as a receiver port will be dynamically
added to the MVR VLAN when it forwards an IGMP report or join message
from an attached host
requesting any of the designated multicast services
supported by the MVR VLAN.
Just remember that only IGMP version 2 or 3
hosts can issue multicast join or leave messages. If MVR must be configured
for an IGMP version 1 host, the multicast groups must be statically assigned
(see “Assigning Static MVR Multicast Groups to Interfaces” on page 576).
■
Non-MVR – An interface that does not participate in the MVR VLAN. (This is
the default type.)