Web Management Guide-R04
Table Of Contents
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Using the Web Interface
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Configuring CPU Guard
- Displaying Memory Utilization
- Resetting the System
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Layer 2 Queue Settings
- Layer 3/4 Priority Settings
- Setting Priority Processing to IP Precedence/DSCP or CoS
- Mapping Ingress DSCP Values to Internal DSCP Values
- Mapping CoS Priorities to Internal DSCP Values
- Mapping Internal DSCP Values to Egress CoS Values
- Mapping IP Precedence Values to Internal DSCP Values
- Mapping IP Port Priority to Internal DSCP Values
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA Authentication, Authorization and Accounting
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- DHCPv4 Snooping
- DHCPv6 Snooping
- IPv4 Source Guard
- IPv6 Source Guard
- ARP Inspection
- Application Filter
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting Community Access Strings
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Switch Clustering
- Setting a Time Range
- Ethernet Ring Protection Switching
- OAM Configuration
- Connectivity Fault Management
- Configuring Global Settings for CFM
- Configuring Interfaces for CFM
- Configuring CFM Maintenance Domains
- Configuring CFM Maintenance Associations
- Configuring Maintenance End Points
- Configuring Remote Maintenance End Points
- Transmitting Link Trace Messages
- Transmitting Loop Back Messages
- Transmitting Delay-Measure Requests
- Displaying Local MEPs
- Displaying Details for Local MEPs
- Displaying Local MIPs
- Displaying Remote MEPs
- Displaying Details for Remote MEPs
- Displaying the Link Trace Cache
- Displaying Fault Notification Settings
- Displaying Continuity Check Errors
- OAM Configuration
- UDLD Configuration
- LBD Configuration
- Smart Pair Configuration
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query for IPv4)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering IGMP Query Packets and Multicast Data
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Multicast VLAN Registration for IPv4
- Multicast VLAN Registration for IPv6
- Basic IP Functions
- IP Configuration
- General IP Routing
- IP Services
- Appendices
- Glossary
Chapter 17
| General IP Routing
Configuring IP Routing Interfaces
– 688 –
Configuring IP Routing Interfaces
Configuring Local and
Remote Interfaces
Use the IP > General > Routing Interface (Add Address) page to configure routing
interfaces for directly connected IPv4 subnets (see “Setting the Switch’s IP Address
(IP Version 4)” on page 663. Or use the IP > IPv6 Configuration pages to configure
routing interfaces for directly connected IPv6 subnets (see “Setting the Switch’s IP
Address (IP Version 6)” on page 667).
If this router is directly connected to end node devices (or connected to end nodes
through shared media) that will be assigned to a specific subnet, then you must
create a router interface for each VLAN that will support routing. The router
interface consists of an IP address and subnet mask. This interface address defines
both the network prefix number to which the router interface is attached and the
router’s host number on that network. In other words, a router interface address
defines the network segment that is connected to that interface, and allows you to
send IP packets to or from the router.
You can specify the IP subnets connected directly to this router by manually
assigning an IP address to each VLAN, or using BOOTP or DHCP to dynamically
assign an address. To specify IP subnets not directly connected to this router, you
can configure static routes (see page 689).
Once IP interfaces have been configured, the switch functions as a multilayer
routing switch, operating at either Layer 2 or 3 as required. All IP packets are routed
directly between local interfaces, or indirectly to remote interfaces using static
routing. All other packets for non-IP protocols (for example, NetBuei, NetWare or
AppleTalk) are switched based on MAC addresses).
To route traffic between remote IP interfaces, the switch should be recognized by
other network nodes as an IP router, either by setting it to advertise itself as the
default gateway or by redirection from another router via the ICMP process used by
various routing protocols.
If another router is designated as the default gateway, then this switch will pass
packets to the router for any unknown hosts or subnets.
To configure the default gateway for IPv4, use the static routing table as described
on page 689, enter 0.0.0.0 for the IP address and subnet mask, and then specify this
switch itself or another router as the gateway. To configure a gateway for IPv6, see
“Configuring the IPv6 Default Gateway” on page 667.