Web Management Guide-R04
Table Of Contents
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Using the Web Interface
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Configuring CPU Guard
- Displaying Memory Utilization
- Resetting the System
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Layer 2 Queue Settings
- Layer 3/4 Priority Settings
- Setting Priority Processing to IP Precedence/DSCP or CoS
- Mapping Ingress DSCP Values to Internal DSCP Values
- Mapping CoS Priorities to Internal DSCP Values
- Mapping Internal DSCP Values to Egress CoS Values
- Mapping IP Precedence Values to Internal DSCP Values
- Mapping IP Port Priority to Internal DSCP Values
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA Authentication, Authorization and Accounting
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- DHCPv4 Snooping
- DHCPv6 Snooping
- IPv4 Source Guard
- IPv6 Source Guard
- ARP Inspection
- Application Filter
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting Community Access Strings
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Switch Clustering
- Setting a Time Range
- Ethernet Ring Protection Switching
- OAM Configuration
- Connectivity Fault Management
- Configuring Global Settings for CFM
- Configuring Interfaces for CFM
- Configuring CFM Maintenance Domains
- Configuring CFM Maintenance Associations
- Configuring Maintenance End Points
- Configuring Remote Maintenance End Points
- Transmitting Link Trace Messages
- Transmitting Loop Back Messages
- Transmitting Delay-Measure Requests
- Displaying Local MEPs
- Displaying Details for Local MEPs
- Displaying Local MIPs
- Displaying Remote MEPs
- Displaying Details for Remote MEPs
- Displaying the Link Trace Cache
- Displaying Fault Notification Settings
- Displaying Continuity Check Errors
- OAM Configuration
- UDLD Configuration
- LBD Configuration
- Smart Pair Configuration
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query for IPv4)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering IGMP Query Packets and Multicast Data
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Multicast VLAN Registration for IPv4
- Multicast VLAN Registration for IPv6
- Basic IP Functions
- IP Configuration
- General IP Routing
- IP Services
- Appendices
- Glossary
Chapter 14
| Multicast Filtering
Multicast VLAN Registration for IPv6
– 637 –
Configuring MVR6
Global Settings
Use the Multicast > MVR6 (Configure Global) page to configure proxy switching
and the robustness variable.
Parameters
These parameters are displayed:
◆ Proxy Switching – Configures MVR proxy switching, where the source port
acts as a host, and the receiver port acts as an MVR router with querier service
enabled. (Default: Enabled)
■
When MVR proxy-switching is enabled, an MVR source port serves as the
upstream or host interface, and the MVR receiver port serves as the querier.
The source port performs only the host portion of MVR by sending
summarized membership reports, and automatically disables MVR router
functions.
■
Receiver ports are known as downstream or router interfaces. These
interfaces perform the standard MVR router functions by maintaining a
database of all MVR subscriptions on the downstream interface. Receiver
ports must therefore be configured on all downstream interfaces which
require MVR proxy service.
■
When the source port receives report and leave messages, it only forwards
them to other source ports.
■
When receiver ports receive any query messages, they are dropped.
■
When changes occurring in the downstream MVR groups are learned by
the receiver ports through report and leave messages, an MVR state change
report is created and sent to the upstream source port, which in turn
forwards this information upstream.
■
When MVR proxy switching is disabled:
■
Any membership reports received from receiver/source ports are
forwarded to all source ports.
■
When a source port receives a query message, it will be forwarded to all
downstream receiver ports.
■
When a receiver port receives a query message, it will be dropped.
◆ Robustness Value – Configures the expected packet loss, and thereby the
number of times to generate report and group-specific queries. (Range: 1-10;
Default: 2)
■
This parameter is used to set the number of times report messages are sent
upstream when changes are learned about downstream groups, and the
number of times group-specific queries are sent to downstream receiver
ports.
■
This parameter only takes effect when MVR6 proxy switching is enabled.