Web Management Guide-R04
Table Of Contents
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Using the Web Interface
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Configuring CPU Guard
- Displaying Memory Utilization
- Resetting the System
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Layer 2 Queue Settings
- Layer 3/4 Priority Settings
- Setting Priority Processing to IP Precedence/DSCP or CoS
- Mapping Ingress DSCP Values to Internal DSCP Values
- Mapping CoS Priorities to Internal DSCP Values
- Mapping Internal DSCP Values to Egress CoS Values
- Mapping IP Precedence Values to Internal DSCP Values
- Mapping IP Port Priority to Internal DSCP Values
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA Authentication, Authorization and Accounting
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- DHCPv4 Snooping
- DHCPv6 Snooping
- IPv4 Source Guard
- IPv6 Source Guard
- ARP Inspection
- Application Filter
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting Community Access Strings
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Switch Clustering
- Setting a Time Range
- Ethernet Ring Protection Switching
- OAM Configuration
- Connectivity Fault Management
- Configuring Global Settings for CFM
- Configuring Interfaces for CFM
- Configuring CFM Maintenance Domains
- Configuring CFM Maintenance Associations
- Configuring Maintenance End Points
- Configuring Remote Maintenance End Points
- Transmitting Link Trace Messages
- Transmitting Loop Back Messages
- Transmitting Delay-Measure Requests
- Displaying Local MEPs
- Displaying Details for Local MEPs
- Displaying Local MIPs
- Displaying Remote MEPs
- Displaying Details for Remote MEPs
- Displaying the Link Trace Cache
- Displaying Fault Notification Settings
- Displaying Continuity Check Errors
- OAM Configuration
- UDLD Configuration
- LBD Configuration
- Smart Pair Configuration
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query for IPv4)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering IGMP Query Packets and Multicast Data
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Multicast VLAN Registration for IPv4
- Multicast VLAN Registration for IPv6
- Basic IP Functions
- IP Configuration
- General IP Routing
- IP Services
- Appendices
- Glossary
Chapter 2
| Using the Web Interface
Navigating the Web Browser Interface
– 61 –
Auto Traffic Control Sets thresholds for broadcast and multicast storms which can be used
to trigger configured rate limits or to shut down a port
242
Configure Global Sets the time to apply the control response after traffic has exceeded
the upper threshold, and the time to release the control response after
traffic has fallen beneath the lower threshold
244
Configure Interface Sets the storm control mode (broadcast or multicast), the traffic
thresholds, the control response, to automatically release a response of
rate limiting, or to send related SNMP trap messages
245
Priority
Default Priority Sets the default priority for each port or trunk 249
Queue Sets queue mode for the switch; sets the service weight for each queue
that will use a weighted or hybrid mode
250
Trust Mode Selects DSCP or CoS priority processing 256
DSCP to DSCP 257
Add Maps DSCP values in incoming packets to per-hop behavior and drop
precedence values for internal priority processing
257
Show Shows the DSCP to DSCP mapping list 257
CoS to DSCP 260
Configure Maps CoS/CFI values in incoming packets to per-hop behavior and drop
precedence values for priority processing
260
Show Shows the CoS to DSCP mapping list 260
DSCP to CoS 262
Add Maps internal per-hop behavior and drop precedence value pairs to CoS
values used in tagged egress packets on a Layer 2 interface
262
Show Shows the DSCP to CoS mapping list 262
IP Precedence to DSCP 264
Add Maps IP precedence values in incoming packets to per-hop behavior
and drop precedence values for priority processing
264
Show Shows the IP Precedence to DSCP mapping list 264
IP Port to DSCP 266
Add Sets TCP/UDP port priority, defining the socket number and associated
per-hop behavior and drop precedence
266
Show Shows the IP Port to DSCP mapping list 266
PHB to Queue 253
Configure Maps internal per-hop behavior values to hardware queues 253
Show Shows the PHB to Queue mapping list 253
DiffServ 269
Configure Class 270
Add Creates a class map for a type of traffic 270
Table 4: Switch Main Menu (Continued)
Menu Description Page