Web Management Guide-R04
Table Of Contents
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Using the Web Interface
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Configuring CPU Guard
- Displaying Memory Utilization
- Resetting the System
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Layer 2 Queue Settings
- Layer 3/4 Priority Settings
- Setting Priority Processing to IP Precedence/DSCP or CoS
- Mapping Ingress DSCP Values to Internal DSCP Values
- Mapping CoS Priorities to Internal DSCP Values
- Mapping Internal DSCP Values to Egress CoS Values
- Mapping IP Precedence Values to Internal DSCP Values
- Mapping IP Port Priority to Internal DSCP Values
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA Authentication, Authorization and Accounting
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- DHCPv4 Snooping
- DHCPv6 Snooping
- IPv4 Source Guard
- IPv6 Source Guard
- ARP Inspection
- Application Filter
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting Community Access Strings
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Switch Clustering
- Setting a Time Range
- Ethernet Ring Protection Switching
- OAM Configuration
- Connectivity Fault Management
- Configuring Global Settings for CFM
- Configuring Interfaces for CFM
- Configuring CFM Maintenance Domains
- Configuring CFM Maintenance Associations
- Configuring Maintenance End Points
- Configuring Remote Maintenance End Points
- Transmitting Link Trace Messages
- Transmitting Loop Back Messages
- Transmitting Delay-Measure Requests
- Displaying Local MEPs
- Displaying Details for Local MEPs
- Displaying Local MIPs
- Displaying Remote MEPs
- Displaying Details for Remote MEPs
- Displaying the Link Trace Cache
- Displaying Fault Notification Settings
- Displaying Continuity Check Errors
- OAM Configuration
- UDLD Configuration
- LBD Configuration
- Smart Pair Configuration
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query for IPv4)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering IGMP Query Packets and Multicast Data
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Multicast VLAN Registration for IPv4
- Multicast VLAN Registration for IPv6
- Basic IP Functions
- IP Configuration
- General IP Routing
- IP Services
- Appendices
- Glossary
Chapter 13
| Basic Administration Protocols
Ethernet Ring Protection Switching
– 490 –
generated R-APS messages is allowed and the reception of all R-APS
messages is allowed.
■
Forwarding – The transmission and reception of traffic is allowed;
transmission, reception and forwarding of R-APS messages is allowed.
■
Unknown – The interface is not in a known state (includes the domain
being disabled).
◆ Local SF – A signal fault generated on a link to the local node.
◆ Local FS – Shows if a forced switch command was issued on this interface.
◆ Local MS – Shows if a manual switch command was issued on this interface.
◆ MEP – The CFM MEP used to monitor the status on this link.
◆ RPL – Shows if this node is connected to the RPL.
◆ Inclusion VLANs – Use this field to specify VLANs that are to be on the
inclusion list of an ERPS domain. (Enter VLAN IDs seperated by a comma, VLAN
IDs 1-4094)
◆ Exclusion VLANs – Use this field to specify VLANs that are to be on the
exclusion list of an ERPS domain.(Enter VLAN IDs seperated by a comma, VLAN
IDs 1-4094)
■
VLANs that are on the exclusion list are protected by the ERPS domain.
■
Any VLAN not listed on either the inclusion or exclusion list will be blocked
on ring ports.
■
Traffic from control VLANs, inclusion VLANs, and exclusion VLANs of an
ERPS domain will be forwarded by non-ERPS ring ports.
■
Use the show erps command to view the inclusion-vlan or exclusion-vlan
list of VLAN IDs - Refer to the CLI Reference Guide for command usage.
Configure Details
◆ Domain Name – Name of a configured ERPS ring. (Range: 1-12 characters)
Service Instances within each ring are based on a unique maintenance
association for the specific users, distinguished by the ring name, maintenance
level, maintenance association’s name, and assigned VLAN. Up to 6 ERPS rings
can be configured on the switch.
◆ Domain ID – ERPS ring identifier used in R-APS messages. (Range: 1-255;
Default: None)
R-APS information is carried in an R-APS PDUs. The last octet of the MAC
address is designated as the Ring ID (01-19-A7-00-00-[Ring ID]). If use of the