ECS4110-52P_Quick Start Guide-R1.0

ManualsBrandsEdgecore Networks ManualsEnterpriseL2+ Gigabit Ethernet Standalone Switch

– 1 –

Quick Start Guide

L2 Gigabit Ethernet Switch

ECS4110-52T and ECS4110-52P

The ECS4110-52T and ECS4110-52P are high-performance enterprise Layer 2

switches that provide 48 10/100/1000BASE-T RJ-45 ports and four Small Form

Factor (SFP) slots that support 1000BASE-SX, 1000BASE-LX, 100BASE-FX, and

1000BASE-T transceivers. The ECS4110-52P switch also provides Power-over-

Ethernet (PoE) capability over its 48 copper wire RJ-45 ports.

OTE

For detailed switch installation information, refer to the Installation Guide,

which is on the Documentation CD included with the switch.

OTE

For Safety and Regulatory information, refer to the Safety and Regulatory

Information document included with the switch.

The switch is designed to be installed in a standard 19-inch equipment rack.

However, you can also install the switch on any flat surface, such as a desktop.

Follow the steps in this guide to install the switch in your network.

1. Unpack the Switch Unpack the switch and check the package contents.

◆ ECS4110-52T or ECS4110-52P L2 Gigabit Ethernet Switch

◆ Bracket Mounting Kit containing two brackets and eight screws for attaching

the brackets to the switch

◆ Four adhesive foot pads

◆ Power cord—either US, Continental Europe or UK

E012013-KS-R01

150200000555A

www.edge-core.com

Summary of content (6 pages)

PAGE 1
Quick Star t Guide L2 Gigabit Ethernet Switch ECS4110-52T and ECS4110-52P The ECS4110-52T and ECS4110-52P are high-performance enterprise Layer 2 switches that provide 48 10/100/1000BASE-T RJ-45 ports and four Small Form Factor (SFP) slots that support 1000BASE-SX, 1000BASE-LX, 100BASE-FX, and 1000BASE-T transceivers. The ECS4110-52P switch also provides Power-overEthernet (PoE) capability over its 48 copper wire RJ-45 ports.
PAGE 2
Quick Start Guide ◆ ◆ ◆ ◆ Console cable (RJ-45 to DB-9) Quick Start Guide (this document) Regulatory and Safety Information Documentation CD — includes Installation Guide and Management Guide 2. Install the Switch The switch can be mounted in a standard 19-inch rack or on a desktop or shelf. Rack Mounting—Following your rack plan, mark the holes in the rack where the switch will be installed. One person should lift the switch into the rack so that it is aligned with the marked holes.
PAGE 3
Quick Start Guide 3. Connect Power To supply AC power to the switch, first verify that the external AC power supply can provide 100 to 240 VAC, 50-60 Hz and 1A minimun for the ECS4110-52T or 7A minimum for the ECS4110-52P. To connect AC power, plug the power cord into a grounded, 3-pin, AC power source and then into the AC socket on the rear of the switch. Caution: Use the AC power cord supplied with the switch.
PAGE 4
Quick Start Guide 5. Make Initial At this point you may need to make a few basic switch configuration changes Configuration before connecting to the network. It is suggested to connect to the switch console Changes port to perform this task. The serial port’s configuration requirements are as follows: 115200 bps, 8 characters, no parity, one stop bit, 8 data bits, and no flow control. You can log in to the command-line interface (CLI) using default settings: User name “admin” with password “admin.
PAGE 5
Quick Start Guide ◆ For the SFP slots, first install SFP transceivers and then connect fiber optic cabling to the transceiver ports. Connect 62.5/125 or 50/125 multimode or 9/125 single-mode fiber with LC connectors. As connections are made, check the port status LEDs to be sure the links are valid. NOTE: For further switch configuration information, refer to the Management Guide, which is on the Documentation CD included with the switch.
PAGE 6
Quick Start Guide Hardware Specifications Item Specification Chassis Specifications SIze (W x D x H) ECS4110-52T: 44.0 x 28 x 4.4 cm (17.32 x 11.0 x 1.73 in) ECS4110-52P: 44.0 x 37.9 x 4.4 cm (17.30 x 14.94 x 1.73 in) Weight ECS4110-52T: 3.14 kg (6.9 lbs) ECS4110-52P: 5.27 kg (11.