ECS4100 Series Web Management Guide-R07
Table Of Contents
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Using the Web Interface
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Configuring CPU Guard
- Displaying Memory Utilization
- Resetting the System
- Using Cloud Management
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA (Authentication, Authorization and Accounting)
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- DHCP Snooping
- DHCPv6 Snooping
- IPv4 Source Guard
- IPv6 Source Guard
- ARP Inspection
- Application Filter
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Power over Ethernet
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting Community Access Strings
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Switch Clustering
- Setting a Time Range
- Ethernet Ring Protection Switching
- Connectivity Fault Management
- Configuring Global Settings for CFM
- Configuring Interfaces for CFM
- Configuring CFM Maintenance Domains
- Configuring CFM Maintenance Associations
- Configuring Maintenance End Points
- Configuring Remote Maintenance End Points
- Transmitting Link Trace Messages
- Transmitting Loop Back Messages
- Transmitting Delay-Measure Requests
- Displaying Local MEPs
- Displaying Details for Local MEPs
- Displaying Local MIPs
- Displaying Remote MEPs
- Displaying Details for Remote MEPs
- Displaying the Link Trace Cache
- Displaying Fault Notification Settings
- Displaying Continuity Check Errors
- OAM Configuration
- UDLD Configuration
- LBD Configuration
- Smart Pair Configuration
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query for IPv4)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering IGMP Packets on an Interface
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Configuring MLD Snooping and Query Parameters
- Setting Immediate Leave Status for MLD Snooping per Interface
- Specifying Static Interfaces for an IPv6 Multicast Router
- Assigning Interfaces to IPv6 Multicast Services
- Filtering MLD Query Packets on an Interface
- Showing MLD Snooping Groups and Source List
- Displaying MLD Snooping Statistics
- Filtering and Throttling MLD Groups
- Multicast VLAN Registration for IPv4
- Multicast VLAN Registration for IPv6
- IP Tools
- IP Configuration
- General IP Routing
- Unicast Routing
- Overview
- Configuring the Routing Information Protocol
- Configuring General Protocol Settings
- Clearing Entries from the Routing Table
- Specifying Network Interfaces
- Specifying Passive Interfaces
- Specifying Static Neighbors
- Configuring Route Redistribution
- Specifying an Administrative Distance
- Configuring Network Interfaces for RIP
- Displaying RIP Interface Settings
- Displaying Peer Router Information
- Resetting RIP Statistics
- IP Services
- Appendices
Figures
– 23 –
Figure 135: Configuring MSTP Interface Settings 234
Figure 136: Displaying MSTP Interface Settings 235
Figure 137: Configuring Rate Limits 238
Figure 138: Configuring Storm Control 240
Figure 139: Storm Control by Limiting the Traffic Rate 240
Figure 140: Storm Control by Shutting Down a Port 241
Figure 141: Configuring ATC Timers 242
Figure 142: Configuring ATC Interface Attributes 245
Figure 143: Setting the Default Port Priority 248
Figure 144: Setting the Queue Mode (Strict) 250
Figure 145: Setting the Queue Mode (WRR) 250
Figure 146: Setting the Queue Mode (Strict and WRR) 251
Figure 147: Setting the Trust Mode 253
Figure 148: Configuring CoS to Queue Mapping 254
Figure 149: Configuring DSCP to Queue Mapping 256
Figure 150: Configuring a Class Map 259
Figure 151: Showing Class Maps 260
Figure 152: Adding Rules to a Class Map 260
Figure 153: Showing the Rules for a Class Map 261
Figure 154: Configuring a Policy Map 263
Figure 155: Showing Policy Maps 263
Figure 156: Adding Rules to a Policy Map 264
Figure 157: Showing the Rules for a Policy Map 265
Figure 158: Attaching a Policy Map to a Port 266
Figure 159: Configuring a Voice VLAN 269
Figure 160: Configuring an OUI Telephony List 270
Figure 161: Showing an OUI Telephony List 270
Figure 162: Configuring Port Settings for a Voice VLAN 272
Figure 163: Configuring the Authentication Sequence 276
Figure 164: Authentication Server Operation 276
Figure 165: Configuring Remote Authentication Server (RADIUS) 279
Figure 166: Configuring Remote Authentication Server (TACACS+) 280
Figure 167: Configuring AAA Server Groups 280
Figure 168: Showing AAA Server Groups 281
Figure 169: Configuring Global Settings for AAA Accounting 283