ECS4100 Series Web Management Guide-R07
Table Of Contents
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Using the Web Interface
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Configuring CPU Guard
- Displaying Memory Utilization
- Resetting the System
- Using Cloud Management
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA (Authentication, Authorization and Accounting)
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- DHCP Snooping
- DHCPv6 Snooping
- IPv4 Source Guard
- IPv6 Source Guard
- ARP Inspection
- Application Filter
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Power over Ethernet
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting Community Access Strings
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Switch Clustering
- Setting a Time Range
- Ethernet Ring Protection Switching
- Connectivity Fault Management
- Configuring Global Settings for CFM
- Configuring Interfaces for CFM
- Configuring CFM Maintenance Domains
- Configuring CFM Maintenance Associations
- Configuring Maintenance End Points
- Configuring Remote Maintenance End Points
- Transmitting Link Trace Messages
- Transmitting Loop Back Messages
- Transmitting Delay-Measure Requests
- Displaying Local MEPs
- Displaying Details for Local MEPs
- Displaying Local MIPs
- Displaying Remote MEPs
- Displaying Details for Remote MEPs
- Displaying the Link Trace Cache
- Displaying Fault Notification Settings
- Displaying Continuity Check Errors
- OAM Configuration
- UDLD Configuration
- LBD Configuration
- Smart Pair Configuration
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query for IPv4)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering IGMP Packets on an Interface
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Configuring MLD Snooping and Query Parameters
- Setting Immediate Leave Status for MLD Snooping per Interface
- Specifying Static Interfaces for an IPv6 Multicast Router
- Assigning Interfaces to IPv6 Multicast Services
- Filtering MLD Query Packets on an Interface
- Showing MLD Snooping Groups and Source List
- Displaying MLD Snooping Statistics
- Filtering and Throttling MLD Groups
- Multicast VLAN Registration for IPv4
- Multicast VLAN Registration for IPv6
- IP Tools
- IP Configuration
- General IP Routing
- Unicast Routing
- Overview
- Configuring the Routing Information Protocol
- Configuring General Protocol Settings
- Clearing Entries from the Routing Table
- Specifying Network Interfaces
- Specifying Passive Interfaces
- Specifying Static Neighbors
- Configuring Route Redistribution
- Specifying an Administrative Distance
- Configuring Network Interfaces for RIP
- Displaying RIP Interface Settings
- Displaying Peer Router Information
- Resetting RIP Statistics
- IP Services
- Appendices
Figures
– 22 –
Figure 100: Assigning Interfaces to Protocol VLANs 195
Figure 101: Showing the Interface to Protocol Group Mapping 195
Figure 102: Configuring IP Subnet VLANs 197
Figure 103: Showing IP Subnet VLANs 197
Figure 104: Configuring MAC-Based VLANs 199
Figure 105: Showing MAC-Based VLANs 199
Figure 106: Configuring VLAN Translation 200
Figure 107: Configuring VLAN Translation 201
Figure 108: Showing the Entries for VLAN Translation 201
Figure 109: Displaying the Dynamic MAC Address Table 204
Figure 110: Clearing Entries in the Dynamic MAC Address Table 205
Figure 111: Setting the Address Aging Time 206
Figure 112: Configuring MAC Address Learning 207
Figure 113: Configuring Static MAC Addresses 209
Figure 114: Displaying Static MAC Addresses 209
Figure 115: Issuing MAC Address Traps (Global Configuration) 210
Figure 116: Issuing MAC Address Traps (Interface Configuration) 210
Figure 117: STP Root Ports and Designated Ports 212
Figure 118: MSTP Region, Internal Spanning Tree, Multiple Spanning Tree 212
Figure 119: Spanning Tree – Common Internal, Common, Internal 213
Figure 120: Configuring Port Loopback Detection 215
Figure 121: Configuring Global Settings for STA (STP) 219
Figure 122: Configuring Global Settings for STA (RSTP) 220
Figure 123: Configuring Global Settings for STA (MSTP) 220
Figure 124: Displaying Global Settings for STA 222
Figure 125: Determining the Root Port 223
Figure 126: Configuring Interface Settings for STA 226
Figure 127: STA Port Roles 228
Figure 128: Displaying Interface Settings for STA 229
Figure 129: Creating an MST Instance 230
Figure 130: Displaying MST Instances 231
Figure 131: Modifying the Priority for an MST Instance 231
Figure 132: Displaying Global Settings for an MST Instance 232
Figure 133: Adding a VLAN to an MST Instance 232
Figure 134: Displaying Members of an MST Instance 233