Web Management Guide-R05
Table Of Contents
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Using the Web Interface
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Configuring CPU Guard
- Displaying Memory Utilization
- Resetting the System
- Using Cloud Management
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA (Authentication, Authorization and Accounting)
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- DHCP Snooping
- IPv4 Source Guard
- ARP Inspection
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Setting Community Access Strings
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Switch Clustering
- Setting a Time Range
- LBD Configuration
- Smart Pair Configuration
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query for IPv4)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering IGMP Query Packets and Multicast Data
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Filtering and Throttling MLD Groups
- Filtering MLD Query Packets on an Interface
- IP Tools
- IP Configuration
- General IP Routing
- Unicast Routing
- Overview
- Configuring the Routing Information Protocol
- Configuring General Protocol Settings
- Clearing Entries from the Routing Table
- Specifying Network Interfaces
- Specifying Passive Interfaces
- Specifying Static Neighbors
- Configuring Route Redistribution
- Specifying an Administrative Distance
- Configuring Network Interfaces for RIP
- Displaying RIP Interface Settings
- Displaying Peer Router Information
- Resetting RIP Statistics
- IP Services
- Appendices
- Glossary
- Index
Chapter 2
| Using the Web Interface
Navigating the Web Browser Interface
– 57 –
Show 392
Alarm Shows all configured alarms 392
Event Shows all configured events 395
Configure Interface
Add
History Periodically samples statistics on a physical interface 397
Statistics Enables collection of statistics on a physical interface 400
Show
History Shows sampling parameters for each entry in the history group 397
Statistics Shows sampling parameters for each entry in the statistics group 400
Show Details
History Shows sampled data for each entry in the history group 397
Statistics Shows sampled data for each entry in the history group 400
Time Range Configures the time to apply an ACL 407
Add Specifies the name of a time range 407
Show Shows the name of configured time ranges 407
Add Rule 407
Absolute Sets exact time or time range 407
Periodic Sets a recurrent time 407
Show Rule Shows the time specified by a rule 407
LDB Loopback Detection 410
Configure Global Enables loopback detection globally, specifies the interval at which to
transmit control frames, specifies the interval to wait before releasing
an interface from shutdown state, specifies response to detect
loopback, and traps to send
410
Configure Interface Enables loopback detection per interface 412
Smart Pair Configures Smart Pairs for providing a traffic backup. 413
Configure Global Sets the ID of a Smart Pair 414
Configure Interface Configures the port members of a smart pair. 414
Show Smart Pair IDs Displays the Smart Pair ID numbers configured. 415
Show Smart Pair Configuration Displays the primary and backup ports of a configured Smart Pair. 416
Restore Smart Pair Traffic Restores traffic manually to the smart pair’s primary port. 416
Tools
Ping Sends ICMP echo request packets to another node on the network 463
Trace Route Shows the route packets take to the specified
destination
464
Table 4: Switch Main Menu (Continued)
Menu Description Page