Web Management Guide-R05
Table Of Contents
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Using the Web Interface
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Configuring CPU Guard
- Displaying Memory Utilization
- Resetting the System
- Using Cloud Management
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA (Authentication, Authorization and Accounting)
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- DHCP Snooping
- IPv4 Source Guard
- ARP Inspection
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Setting Community Access Strings
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Switch Clustering
- Setting a Time Range
- LBD Configuration
- Smart Pair Configuration
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query for IPv4)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering IGMP Query Packets and Multicast Data
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Filtering and Throttling MLD Groups
- Filtering MLD Query Packets on an Interface
- IP Tools
- IP Configuration
- General IP Routing
- Unicast Routing
- Overview
- Configuring the Routing Information Protocol
- Configuring General Protocol Settings
- Clearing Entries from the Routing Table
- Specifying Network Interfaces
- Specifying Passive Interfaces
- Specifying Static Neighbors
- Configuring Route Redistribution
- Specifying an Administrative Distance
- Configuring Network Interfaces for RIP
- Displaying RIP Interface Settings
- Displaying Peer Router Information
- Resetting RIP Statistics
- IP Services
- Appendices
- Glossary
- Index
Chapter 2
| Using the Web Interface
Navigating the Web Browser Interface
– 56 –
Configure Engine 367
Set Engine ID Sets the SNMP v3 engine ID on this switch 367
Add Remote Engine Sets the SNMP v3 engine ID for a remote device 368
Show Remote Engine Shows configured engine ID for remote devices 368
Configure View 369
Add View Adds an SNMP v3 view of the OID MIB 369
Show View Shows configured SNMP v3 views 369
Add OID Subtree Specifies a part of the subtree for the selected view 369
Show OID Subtree Shows the subtrees assigned to each view 369
Configure Group 372
Add Adds a group with access policies for assigned users 372
Show Shows configured groups and access policies 372
Configure User
Add Community Configures community strings and access mode 377
Show Community Shows community strings and access mode 377
Add SNMPv3 Local User Configures SNMPv3 users on this switch 378
Show SNMPv3 Local User Shows SNMPv3 users configured on this switch 378
Change SNMPv3 Local User Group Assign a local user to a new group 378
Add SNMPv3 Remote User Configures SNMPv3 users from a remote device 381
Show SNMPv3 Remote User Shows SNMPv3 users set from a remote device 378
Configure Trap 384
Add Configures trap managers to receive messages on key events that occur
on this switch
384
Show Shows configured trap managers 384
Configure Notify Filter
Add Creates an SNMP notification log 388
Show Shows the configured notification logs 388
Show Statistics Shows the status of SNMP communications 390
RMON Remote Monitoring 392
Configure Global
Add
Alarm Sets threshold bounds for a monitored variable 392
Event Creates a response event for an alarm 395
Table 4: Switch Main Menu (Continued)
Menu Description Page