Web Management Guide-R05
Table Of Contents
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Using the Web Interface
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Configuring CPU Guard
- Displaying Memory Utilization
- Resetting the System
- Using Cloud Management
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA (Authentication, Authorization and Accounting)
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- DHCP Snooping
- IPv4 Source Guard
- ARP Inspection
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Setting Community Access Strings
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Switch Clustering
- Setting a Time Range
- LBD Configuration
- Smart Pair Configuration
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query for IPv4)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering IGMP Query Packets and Multicast Data
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Filtering and Throttling MLD Groups
- Filtering MLD Query Packets on an Interface
- IP Tools
- IP Configuration
- General IP Routing
- Unicast Routing
- Overview
- Configuring the Routing Information Protocol
- Configuring General Protocol Settings
- Clearing Entries from the Routing Table
- Specifying Network Interfaces
- Specifying Passive Interfaces
- Specifying Static Neighbors
- Configuring Route Redistribution
- Specifying an Administrative Distance
- Configuring Network Interfaces for RIP
- Displaying RIP Interface Settings
- Displaying Peer Router Information
- Resetting RIP Statistics
- IP Services
- Appendices
- Glossary
- Index
Chapter 14
| Multicast Filtering
MLD Snooping (Snooping and Query for IPv6)
– 446 –
An IPv6 address must be configured on the VLAN interface from which the
querier will act if elected. When serving as the querier, the switch uses this IPv6
address as the query source address.
The querier will not start or will disable itself after having started if it detects an
IPv6 multicast router on the network.
◆ Robustness – MLD Snooping robustness variable. A port will be removed from
the receiver list for a multicast service when no MLD reports are detected in
response to a number of MLD queries. The robustness variable sets the number
of queries on ports for which there is no report. (Range: 2-10 Default: 2)
◆ Query Interval – The interval between sending MLD general queries.
(Range: 60-125 seconds; Default: 125 seconds)
This attribute applies when the switch is serving as the querier.
An MLD general query message is sent by the switch at the interval specified by
this attribute. When this message is received by downstream hosts, all receivers
build an MLD report for the multicast groups they have joined.
◆ Query Max Response Time – The maximum response time advertised in MLD
general queries. (Range: 5-25 seconds; Default: 10 seconds)
This attribute controls how long the host has to respond to an MLD Query
message before the switch deletes the group if it is the last member.
◆ Router Port Expiry Time – The time the switch waits after the previous querier
stops before it considers the router port (i.e., the interface that had been
receiving query packets) to have expired. (Range: 300-500 seconds;
Default: 300 seconds)
◆ MLD Snooping Version – The protocol version used for compatibility with
other devices on the network. This is the MLD version the switch uses to send
snooping reports. (Range: 1-2; Default: 2)
◆ Unknown Multicast Mode – The action for dealing with unknown multicast
packets. Options include:
■
Flood – Floods any received IPv6 multicast packets that have not been
requested by a host to all ports in the VLAN.
■
To Router Port – Forwards any received IPv6 multicast packets that have
not been requested by a host to ports that are connected to a detected
multicast router. (This is the default action.)
Web Interface
To configure general settings for MLD Snooping:
1. Click Multicast, MLD Snooping, General.
2. Adjust the settings as required.