Web Management Guide-R05
Table Of Contents
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Using the Web Interface
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Configuring CPU Guard
- Displaying Memory Utilization
- Resetting the System
- Using Cloud Management
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA (Authentication, Authorization and Accounting)
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- DHCP Snooping
- IPv4 Source Guard
- ARP Inspection
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Setting Community Access Strings
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Switch Clustering
- Setting a Time Range
- LBD Configuration
- Smart Pair Configuration
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query for IPv4)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering IGMP Query Packets and Multicast Data
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Filtering and Throttling MLD Groups
- Filtering MLD Query Packets on an Interface
- IP Tools
- IP Configuration
- General IP Routing
- Unicast Routing
- Overview
- Configuring the Routing Information Protocol
- Configuring General Protocol Settings
- Clearing Entries from the Routing Table
- Specifying Network Interfaces
- Specifying Passive Interfaces
- Specifying Static Neighbors
- Configuring Route Redistribution
- Specifying an Administrative Distance
- Configuring Network Interfaces for RIP
- Displaying RIP Interface Settings
- Displaying Peer Router Information
- Resetting RIP Statistics
- IP Services
- Appendices
- Glossary
- Index
Chapter 13
| Basic Administration Protocols
Link Layer Discovery Protocol
– 356 –
Port Details – 802.3 Extension Trunk Information
◆ Remote Link Aggregation Capable – Shows if the remote port is not in link
aggregation state and/or it does not support link aggregation.
◆ Remote Link Aggregation Status – The current aggregation status of the link.
◆ Remote Link Port ID – This object contains the IEEE 802.3 aggregated port
identifier, aAggPortID (IEEE 802.3-2002, 30.7.2.1.1), derived from the ifNumber
of the ifIndex for the port component associated with the remote system. If the
remote port is not in link aggregation state and/or it does not support link
aggregation, this value should be zero.
Port Details – 802.3 Extension Frame Information
◆ Remote Max Frame Size – An integer value indicating the maximum
supported frame size in octets on the port component associated with the
remote system.
Port Details – LLDP-MED Capability
8
◆ Device Class – Any of the following categories of endpoint devices:
■
Class 1 – The most basic class of endpoint devices.
■
Class 2 – Endpoint devices that supports media stream capabilities.
■
Class 3 – Endpoint devices that directly supports end users of the IP
communication systems.
■
Network Connectivity Device – Devices that provide access to the IEEE 802
based LAN infrastructure for LLDP-MED endpoint devices. These may be
any LAN access device including LAN switch/router, IEEE 802.1 bridge, IEEE
802.3 repeater, IEEE 802.11 wireless access point, or any device that
supports the IEEE 802.1AB and MED extensions defined by this Standard
and can relay IEEE 802 frames via any method.
◆ Supported Capabilities – The supported set of capabilities that define the
primary function(s) of the port:
■
LLDP-MED Capabilities
■
Network Policy
■
Location Identification
■
Extended Power via MDI – PSE
■
Extended Power via MDI – PD
■
Inventory
◆ Current Capabilities – The set of capabilities that define the primary
function(s) of the port which are currently enabled.
8. These fields are only displayed for end-node devices advertising LLDP-MED TLVs.