Web Management Guide-R07
Table Of Contents
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Introduction
- Key Features
- Description of Software Features
- Configuration Backup and Restore
- Authentication
- Access Control Lists
- Port Configuration
- Rate Limiting
- Port Mirroring
- Port Trunking
- Storm Control
- Static MAC Addresses
- IP Address Filtering
- IEEE 802.1D Bridge
- Store-and-Forward Switching
- Spanning Tree Algorithm
- Virtual LANs
- IEEE 802.1Q Tunneling (QinQ)
- Traffic Prioritization
- Quality of Service
- IP Routing
- Address Resolution Protocol
- Multicast Filtering
- Link Layer Discovery Protocol
- System Defaults
- Introduction
- Web Configuration
- Using the Web Interface
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Configuring CPU Guard
- Displaying Memory Utilization
- Resetting the System
- Using Cloud Management
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA (Authentication, Authorization and Accounting)
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- DHCP Snooping
- IPv4 Source Guard
- ARP Inspection
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Power over Ethernet
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Setting Community Access Strings
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Switch Clustering
- Setting a Time Range
- LBD Configuration
- Smart Pair Configuration
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query for IPv4)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering IGMP Query Packets and Multicast Data
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Filtering and Throttling MLD Groups
- Filtering MLD Query Packets on an Interface
- IP Tools
- IP Configuration
- General IP Routing
- Unicast Routing
- Overview
- Configuring the Routing Information Protocol
- Configuring General Protocol Settings
- Clearing Entries from the Routing Table
- Specifying Network Interfaces
- Specifying Passive Interfaces
- Specifying Static Neighbors
- Configuring Route Redistribution
- Specifying an Administrative Distance
- Configuring Network Interfaces for RIP
- Displaying RIP Interface Settings
- Displaying Peer Router Information
- Resetting RIP Statistics
- IP Services
- Appendices
- Glossary
Figures
– 24 –
Figure 170: Creating an ACL 279
Figure 171: Showing a List of ACLs 280
Figure 172: Configuring a Standard IPv4 ACL 281
Figure 173: Configuring an Extended IPv4 ACL 284
Figure 174: Configuring a Standard IPv6 ACL 285
Figure 175: Configuring an Extended IPv6 ACL 287
Figure 176: Configuring a MAC ACL 289
Figure 177: Configuring a ARP ACL 291
Figure 178: Binding a Port to an ACL 292
Figure 179: Showing ACL Statistics 295
Figure 180: Creating an IP Address Filter for Management Access 296
Figure 181: Showing IP Addresses Authorized for Management Access 297
Figure 182: Configuring Port Security 299
Figure 183: Configuring Port Authentication 300
Figure 184: Configuring Global Settings for 802.1X Port Authentication 301
Figure 185: Configuring Interface Settings for 802.1X Port Authenticator 305
Figure 186: Showing Statistics for 802.1X Port Authenticator 307
Figure 187: Protecting Against DoS Attacks 309
Figure 188: Configuring Global Settings for DHCP Snooping 313
Figure 189: Configuring DHCP Snooping on a VLAN 314
Figure 190: Configuring the Port Mode for DHCP Snooping 316
Figure 191: Displaying the Binding Table for DHCP Snooping 317
Figure 192: Setting the Filter Type for IPv4 Source Guard 319
Figure 193: Configuring Static Bindings for IPv4 Source Guard 321
Figure 194: Displaying Static Bindings for IPv4 Source Guard 322
Figure 195: Showing the IPv4 Source Guard Binding Table 323
Figure 196: Configuring Global Settings for ARP Inspection 326
Figure 197: Configuring VLAN Settings for ARP Inspection 327
Figure 198: Configuring Interface Settings for ARP Inspection 328
Figure 199: Displaying Statistics for ARP Inspection 330
Figure 200: Displaying the ARP Inspection Log 331
Figure 201: Configuring Settings for System Memory Logs 335
Figure 202: Showing Error Messages Logged to System Memory 336
Figure 203: Configuring Settings for Remote Logging of Error Messages 337
Figure 204: Configuring SMTP Alert Messages 338