Web Management Guide-R07
Table Of Contents
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Introduction
- Key Features
- Description of Software Features
- Configuration Backup and Restore
- Authentication
- Access Control Lists
- Port Configuration
- Rate Limiting
- Port Mirroring
- Port Trunking
- Storm Control
- Static MAC Addresses
- IP Address Filtering
- IEEE 802.1D Bridge
- Store-and-Forward Switching
- Spanning Tree Algorithm
- Virtual LANs
- IEEE 802.1Q Tunneling (QinQ)
- Traffic Prioritization
- Quality of Service
- IP Routing
- Address Resolution Protocol
- Multicast Filtering
- Link Layer Discovery Protocol
- System Defaults
- Introduction
- Web Configuration
- Using the Web Interface
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Configuring CPU Guard
- Displaying Memory Utilization
- Resetting the System
- Using Cloud Management
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA (Authentication, Authorization and Accounting)
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- DHCP Snooping
- IPv4 Source Guard
- ARP Inspection
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Power over Ethernet
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Setting Community Access Strings
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Switch Clustering
- Setting a Time Range
- LBD Configuration
- Smart Pair Configuration
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query for IPv4)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering IGMP Query Packets and Multicast Data
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Filtering and Throttling MLD Groups
- Filtering MLD Query Packets on an Interface
- IP Tools
- IP Configuration
- General IP Routing
- Unicast Routing
- Overview
- Configuring the Routing Information Protocol
- Configuring General Protocol Settings
- Clearing Entries from the Routing Table
- Specifying Network Interfaces
- Specifying Passive Interfaces
- Specifying Static Neighbors
- Configuring Route Redistribution
- Specifying an Administrative Distance
- Configuring Network Interfaces for RIP
- Displaying RIP Interface Settings
- Displaying Peer Router Information
- Resetting RIP Statistics
- IP Services
- Appendices
- Glossary
Chapter 18
| Unicast Routing
Configuring the Routing Information Protocol
– 520 –
◆ Receive Version – The RIP version to receive on an interface.
■
RIPv1: Accepts only RIPv1 packets.
■
RIPv2: Accepts only RIPv2 packets.
■
RIPv1 and RIPv2: Accepts RIPv1 and RIPv2 packets.
■
Do Not Receive: Does not accept incoming RIP packets. This option does
not add any dynamic entries to the routing table for an interface.
The default depends on the setting for the Global RIP Version. (See
“Configuring General Protocol Settings” on page 507.)
◆ Authentication Type – Specifies the type of authentication required for
exchanging RIPv2 protocol messages. (Default: No Authentication)
■
No Authentication: No authentication is required.
■
Simple Password: Requires the interface to exchange routing information
with other routers based on an authorized password. (Note that
authentication only applies to RIPv2.)
■
MD5: Message Digest 5 (MD5) authentication.
MD5 is a one-way hash algorithm is that takes the authentication key and
produces a 128 bit message digest or “fingerprint.” This makes it
computationally infeasible to produce two messages having the same
message digest, or to produce any message having a given pre-specified
target message digest.
◆ Authentication Key – Specifies the key to use for authenticating RIPv2 packets.
For authentication to function properly, both the sending and receiving
interface must use the same password. (Range: 1-16 characters, case sensitive)
◆ Instability Prevention – Specifies the method used to reduce the convergence
time when the network topology changes, and to prevent RIP protocol
messages from looping back to the source router.
■
Split Horizon – This method never propagate routes back to an interface
from which they have been acquired.
■
Poison Reverse – This method propagates routes back to an interface from
which they have been acquired, but sets the distance-vector metrics to
infinity. This provides faster convergence. (This is the default setting.)
■
None – No loopback prevention method is employed. If a loop occurs
without using any prevention method, the hop count for a route may be
gradually incremented to infinity (that is, 16) before the route is deemed
unreachable.