Web Management Guide-R07
Table Of Contents
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Introduction
- Key Features
- Description of Software Features
- Configuration Backup and Restore
- Authentication
- Access Control Lists
- Port Configuration
- Rate Limiting
- Port Mirroring
- Port Trunking
- Storm Control
- Static MAC Addresses
- IP Address Filtering
- IEEE 802.1D Bridge
- Store-and-Forward Switching
- Spanning Tree Algorithm
- Virtual LANs
- IEEE 802.1Q Tunneling (QinQ)
- Traffic Prioritization
- Quality of Service
- IP Routing
- Address Resolution Protocol
- Multicast Filtering
- Link Layer Discovery Protocol
- System Defaults
- Introduction
- Web Configuration
- Using the Web Interface
- Basic Management Tasks
- Displaying System Information
- Displaying Hardware/Software Versions
- Configuring Support for Jumbo Frames
- Displaying Bridge Extension Capabilities
- Managing System Files
- Setting the System Clock
- Configuring the Console Port
- Configuring Telnet Settings
- Displaying CPU Utilization
- Configuring CPU Guard
- Displaying Memory Utilization
- Resetting the System
- Using Cloud Management
- Interface Configuration
- VLAN Configuration
- Address Table Settings
- Spanning Tree Algorithm
- Congestion Control
- Class of Service
- Quality of Service
- VoIP Traffic Configuration
- Security Measures
- AAA (Authentication, Authorization and Accounting)
- Configuring User Accounts
- Web Authentication
- Network Access (MAC Address Authentication)
- Configuring HTTPS
- Configuring the Secure Shell
- Access Control Lists
- Filtering IP Addresses for Management Access
- Configuring Port Security
- Configuring 802.1X Port Authentication
- DoS Protection
- DHCP Snooping
- IPv4 Source Guard
- ARP Inspection
- Basic Administration Protocols
- Configuring Event Logging
- Link Layer Discovery Protocol
- Power over Ethernet
- Simple Network Management Protocol
- Configuring Global Settings for SNMP
- Setting the Local Engine ID
- Specifying a Remote Engine ID
- Setting SNMPv3 Views
- Configuring SNMPv3 Groups
- Setting Community Access Strings
- Configuring Local SNMPv3 Users
- Configuring Remote SNMPv3 Users
- Specifying Trap Managers
- Creating SNMP Notification Logs
- Showing SNMP Statistics
- Remote Monitoring
- Switch Clustering
- Setting a Time Range
- LBD Configuration
- Smart Pair Configuration
- Multicast Filtering
- Overview
- Layer 2 IGMP (Snooping and Query for IPv4)
- Configuring IGMP Snooping and Query Parameters
- Specifying Static Interfaces for a Multicast Router
- Assigning Interfaces to Multicast Services
- Setting IGMP Snooping Status per Interface
- Filtering IGMP Query Packets and Multicast Data
- Displaying Multicast Groups Discovered by IGMP Snooping
- Displaying IGMP Snooping Statistics
- Filtering and Throttling IGMP Groups
- MLD Snooping (Snooping and Query for IPv6)
- Filtering and Throttling MLD Groups
- Filtering MLD Query Packets on an Interface
- IP Tools
- IP Configuration
- General IP Routing
- Unicast Routing
- Overview
- Configuring the Routing Information Protocol
- Configuring General Protocol Settings
- Clearing Entries from the Routing Table
- Specifying Network Interfaces
- Specifying Passive Interfaces
- Specifying Static Neighbors
- Configuring Route Redistribution
- Specifying an Administrative Distance
- Configuring Network Interfaces for RIP
- Displaying RIP Interface Settings
- Displaying Peer Router Information
- Resetting RIP Statistics
- IP Services
- Appendices
- Glossary
Chapter 13
| Basic Administration Protocols
Simple Network Management Protocol
– 375 –
swMemoryUtiFallingThreshold
Notification
1.3.6.1.4.1.259.10.1.43.2.1.0.110 This notification indicates that the memory
utilization has fallen from
memoryUtiRisingThreshold to
memoryUtiFallingThreshold.
dhcpRougeServerAttackTrap 1.3.6.1.4.1.259.10.1.43.2.1.0.114 This trap is sent when receiving a DHCP packet from
a rouge server.
macNotificationTrap 1.3.6.1.4.1.259.10.1.43.2.1.0.138 This trap is sent when there are changes of the
dynamic MAC addresses on the switch.
lbdDetectionTrap 1.3.6.1.4.1.259.10.1.43.2.1.0.141 This trap is sent when a loopback condition is
detected by LBD.
lbdRecoveryTrap 1.3.6.1.4.1.259.10.1.43.2.1.0.142 This trap is sent when a recovery is done by LBD.
sfpThresholdAlarmWarnTrap 1.3.6.1.4.1.259.10.1.43.2.1.0.189 This trap is sent when the sfp's A/D quantity is not
within alarm/warning thresholds.
userAuthenticationFailureTrap 1.3.6.1.4.1.259.10.1.43.2.1.0.199 This trap will be triggered if authentication fails.
userAuthenticationSuccessTrap 1.3.6.1.4.1.259.10.1.43.2.1.0.200 This trap will be triggered if authentication is
successful.
loginTrap 1.3.6.1.4.1.259.10.1.43.2.1.0.201 This trap is sent when user logs in.
logoutTrap 1.3.6.1.4.1.259.10.1.43.2.1.0.202 This trap is sent when user logs out.
fileCopyTrap 1.3.6.1.4.1.259.10.1.43.2.1.0.208 This trap is sent when file copy is executed.
If the copy action is triggered by the system, the
login user information (trapVarLoginUserName/
trapVarSessionType/
trapVarLoginInetAddressTypes/
trapVarLoginInetAddres) will be a null value.
userauthCreateUserTrap 1.3.6.1.4.1.259.10.1.43.2.1.0.209 This trap is sent when a user account is created.
userauthDeleteUserTrap 1.3.6.1.4.1.259.10.1.43.2.1.0.210 This trap is sent when a user account is deleted.
userauthModifyUserPrivilegeTrap 1.3.6.1.4.1.259.10.1.43.2.1.0.211 This trap is sent when user privilege is modified.
cpuGuardControlTrap 1.3.6.1.4.1.259.10.1.43.2.1.0.213 This trap is sent when CPU utilization rises above
the high-watermark the first time or when CPU
utilization rises from below the low-watermark to
above the high-watermark.
cpuGuardReleaseTrap 1.3.6.1.4.1.259.10.1.43.2.1.0.214 This trap is sent when CPU utilization falls from
above the high-watermark to below the low-
watermark.
* These are legacy notifications and therefore must be enabled in conjunction with the corresponding traps on the SNMP
Configuration menu.
Table 26: Supported Notification Messages (Continued)
Model Level Group