ECS2020 V1.0.2.11 SWR Release Note

ManualsBrandsEdgecore Networks ManualsEnterprise10/28 Gigabit Web-Smart Ethernet Switch

ENGINEERING RELEASE NOTES

6/2000 P/N: 9038023-04 Subject to Change Without Notice

Page: 1 of 6

F0615-E

WebSmart SwitchECS2020-10P/10T/28T/28P

Firmware Version 1.0.2.11

INTRODUCTION:

The ECS2020-10P/10T/10PP is a Gigabit Ethernet Layer 2 switch featuring 8 ports 10/100/1000 ports,

and 2 Gigabit Ethernet SFPuplink ports.

The ECS2020-28P/28T is a Gigabit Ethernet Layer 2 switch featuring 24 ports 10/100/1000 ports, and

4 Gigabit Ethernet combo uplink ports.

The ECS2020-10P/10T/10PP/28P/28T is ideal for operator to deploy SMB network providing

download/upload 10/100/1000Mbps high speed for triple play service.

It is recommended that one thoroughly review this release notes prior to the installation

or upgrade of this product.

FIRMWARE SPECIFICATION:

Status

Version No.

Type

Release Date

Formal Version

1.0.2.11

(ECS2020-10T：26551)

(ECS2020-10P：26552)

(ECS2020-28T：26553)

(ECS2020-28P：26554)

2021/6/11

Formal Version

1.0.2.9

(ECS2020-10T：26323)

(ECS2020-10P：26324)

(ECS2020-28T：26325)

(ECS2020-28P：26326)

2021/3/15

Formal Version

1.0.2.8

(ECS2020-10T：26315)

(ECS2020-10P：26316)

(ECS2020-28T：26317)

(ECS2020-28P：26318)

2021/3/4

Summary of content (22 pages)

PAGE 1
ENGINEERING RELEASE NOTES WebSmart SwitchECS2020-10P/10T/28T/28P Firmware Version 1.0.2.11 INTRODUCTION: The ECS2020-10P/10T/10PP is a Gigabit Ethernet Layer 2 switch featuring 8 ports 10/100/1000 ports, and 2 Gigabit Ethernet SFPuplink ports. The ECS2020-28P/28T is a Gigabit Ethernet Layer 2 switch featuring 24 ports 10/100/1000 ports, and 4 Gigabit Ethernet combo uplink ports.
PAGE 2
ENGINEERING RELEASE NOTES Formal Version 1.0.2.7 2021/2/27 (ECS2020-10T：26305) (ECS2020-10P：26306) (ECS2020-28T：26307) (ECS2020-28P：26308) Formal Version 1.0.2.6 2020/12/29 (ECS2020-10T：26134) (ECS2020-10P：26135) (ECS2020-28T：26136) (ECS2020-28P：26137) Formal Version 1.0.2.5 2020/12/03 (ECS2020-10T：26072) (ECS2020-10P：26073) (ECS2020-28T：26068) (ECS2020-28P：26069) Formal Version 1.0.2.4 2020/08/06 (ECS2020-10T：25957) (ECS2020-10P：25962) (ECS2020-28T：25959) (ECS2020-28P：25960) Formal Version 1.
PAGE 3
ENGINEERING RELEASE NOTES (ECS2020-10P：19737) (ECS2020-28T：19717) Formal Version 1.0.0.2 2018/03/06 (ECS2020-10T：19631) (ECS2020-10P：19636) (ECS2020-28T：19637) (ECS2020-28P：19640) Formal Version 1.0.0.1 2018/01/29 (ECS2020-10T：19277) (ECS2020-10P：19278) (ECS2020-28T：19279) (ECS2020-28P：19283) Formal Version 1.0.0.0 2018/01/11 (ECS2020-10T：19023) (ECS2020-10P：19024) (ECS2020-28T：19025) Formal Version 1.0.0.0 2017/11/03 (18672) Formal Version 1.0.0.0 2017/10/30 (18649) Formal Version 1.0.0.
PAGE 4
ENGINEERING RELEASE NOTES LOADER: Status Version Type Release Date No. Testing Version 1.00.002 2017/3/9 HARDWARE COMPATIBILITY: ALL BOOTPROM COMPATIBILITY: ALL NETWORK MANAGEMENT SOFTWARE SUPPORT: NMS Platform Version Module No. No. TBD If you install this image, you may not have control of all of the latest features of this product until the next version(s) of network management software. Please review the software release notes for your specific network management platform for details.
PAGE 5
ENGINEERING RELEASE NOTES Please see the SMC 功能列表-20170614.xls INSTALLATION AND CONFIGURATION NOTES: In general, the ECS2020 Switch will be shipped to you pre-configured with this version of firmware. If you would like to upgrade an existing ECS2020 Switch, please follow the user manual that are included with your firmware image upgrade kit. FIRMWARE CHANGES AND ENHANCEMENTS: The following Known Issues have been fixed in this release of firmware. Loader V1.00.002 1 Init Init Runtime V0.0.0.
PAGE 6
ENGINEERING RELEASE NOTES EPR Headline 1 Add MVR function support 2 Runtime V1.0.2.9, Loader V1.00.002 EPR Headline Mac Address Table OID： 1 1.3.6.1.2.1.17.7.1.2.2 2 Runtime V1.0.2.8, Loader V1.00.002 EPR Headline "ONVIF occupy VLAN 2 1 option1: change default to other VLAN 11692 option2: due to default ONVIF is disabled, left the VLAN ID value to empty" 2 Runtime V1.0.2.7, Loader V1.00.002 EPR Headline Mac Address Table OID： 1. dot1dTpFdbAddress:1.3.6.1.2.1.17.4.3.1.1 1 2.
PAGE 7
ENGINEERING RELEASE NOTES 9752 option2: due to default ONVIF is disabled, left the VLAN ID value to empty 2 9752 Disconnections that are not timeout related 3 9752 Webpage was saved but the table doesn't actually update 4 Sometimes the device image wouldn't fully load (Chrome version Version 9752 80.0.3987.
PAGE 8
ENGINEERING RELEASE NOTES Runtime V1.0.2.4, Loader V1.00.002 EPR Headline Fix jumbo frame display problem as 1 wrong packet problem -----------------------修復 jumbo 幀顯示問題为错包问题 Runtime V1.0.2.3, Loader V1.00.002 EPR Headline Fix the problem that the configuration save restart does not take effect after modifying 172.168.1.1 mask 1 255.255.252.0 ---------------------修復修改 172.168.1.1 mask255.255.252.0 后配置存盤重啟不生效的問題 Runtime V1.0.2.2, Loader V1.00.
PAGE 9
ENGINEERING RELEASE NOTES discovery of onvif protocol --------------------增加 ONVIF 协议的 NVR 和 IPC 的发现 Runtime V1.0.2.0, Loader V1.00.002 EPR Headline 1 ECS2020-08_023 cannot modify priority in WEB ECS2020-08_024 no STP role information in WEB ECS2020-08_025 cannot modify BPDU hello time, forward delay, max age in WEB can't disable STP per port in WEB.
PAGE 10
ENGINEERING RELEASE NOTES Runtime V1.0.0.2(informal), Loader V1.00.002 EPR 1 ECS2020-201802_26 Headline Telnet 无法在 web 上打开和关闭 2 ECS2020-201802_28 繁体中文显示问题， 3 ECS2020-201803_06 SNMP 找不到 Software Version 4 ECS2020-201803_06 ECS2020 软件版本号由 v1.0.0.1 改为 v1.0.0.2 Runtime V1.0.0.1(informal), Loader V1.00.002 EPR 1 ECS2020-201801_29 Headline ECS2020 软件版本号由 v1.0.0.0 改为 v1.0.0.1 Runtime V1.0.0.0(informal), Loader V1.00.
PAGE 11
ENGINEERING RELEASE NOTES (已经把默认 Circuit ID&Remote ID 格式修改成 Edgecore 一致) 7 ECS2020-11_007 拿掉 dhcp relay 功能后，CLI 命令删除不完全，有遗漏 (已把多余的 show ip dhcp relay 拿掉) ACL 中 IP expand 的 source IP address 無法指定 host 或 range；Web, CLI 都 8 ECS2020-11_008 一樣，Apply 後都自動改成 any (已解决此问题，目前可正常配置 host 或 range) ACL 默认 Mask(0.0.0.0)做用是 host 与 Edgecore 不一致；修改为 9 ECS2020-11_009 default(0.0.0.0)-->host, 空-->any;255.255.255.255-->host；同时修改 web 描述 (已把修改为 default(0.0.0.0)-->host, 空-->any,并修改了 WEB 的描述) Runtime V1.0.0.
PAGE 12
ENGINEERING RELEASE NOTES 更 IP 為 192.168.88.10 後再度啟用 DHCP Server . Client 端取得 IP 還是 192.168.2.XX （wireshark ）另外 IP address 可以任意修改，不清楚用意為何？？ 13 ECS2020-10_005 14 15 ECS2020-10_009 restore factory setting 後，已修正删除 backup-config； ECS2020-10_009 但是利用 Reset button 還是將 Backup-config 刪除 Web ECS2020-10_010 16 ECS2020-10_011 17 修改 None-Pd 为 Non-PD LLDP neighbor 顯示有點慢，另外 Bridge, Router .. CLI 有， WEB 卻沒有 SNMPwalk Enterprise OID .似乎還沒完成。。开机时间变长问题，“V1.0.0.
PAGE 13
ENGINEERING RELEASE NOTES Reboot switch, PoE up at port #2,#3, what's priority order? ECS2020-08_083 All 8 PoE ports connect 30W PDs in same moment, switch will reboot UTC 0 的四个时区设置后无显示，默认需修改，参考 word，参考 EC 提供的 word ECS2020-08_085 （*10012.
PAGE 14
ENGINEERING RELEASE NOTES Runtime V1.0.0.0(informal), Loader V1.00.002 EPR 1 ECS2020-08_001 2 Headline 升級失敗，導致系統異常，RJ45 口不 work 匯出的 Config 用 word 開啟變更編碼還是看不懂, 是編碼的問題嗎 ?? ECS2020-08_002 或是一開始設計就是有加密，還是…..
PAGE 15
ENGINEERING RELEASE NOTES Management >> Configuration Management ..點選 [ SAVE ] ，才算是真正的存檔。功能設定的 ( save ) 代表的應該是 APPLY . 防止客戶搞混，是否應該修改成（ Apply 或是 OK ）.. Apply -->中文 18 ECS2020-08_026 19 ECS2020-08_028 (套用 ) Save-->英文（存檔 ) STP port fast - network mode , what is network mode? STP trap, STP trap port count start form '0', EX: port #1 Topology Change, but trap content is "port 0 change..." 20 ECS2020-08_029 LLDP PDU flooding enabled prevents executing mSTP enable.
PAGE 16
ENGINEERING RELEASE NOTES IPv4 expand ACL : 10ACL(10-19) , 10ACE per ACL , Wildcards mask? IPv6 standard ACL : 10ACL(26-35) , 10ACE per ACL, Mask(0-128)? IPv6 expand ACL : 10ACL(36-45) , 10ACE per ACL , Mask(0-128)? MAC expand ACL : 6ACL(20-25) , 10ACE per ACL , not support mask? mac format? (要改一般 mask 不能用 cisco Wildcards mask 全部改 mask) , web / cli 都一樣 36 ECS2020-08_066 IPv4 & IPv6 expand ACL support IP/TCP/UDP protocol, does not support mask for port No.(CLI/Web 增加) 37 ECS2020-08_069 1.
PAGE 17
ENGINEERING RELEASE NOTES 58 ECS2020-08_109 2. DHCP binding entry per port ? per system? no limitation!? 59 ECS2020-08_113 2) remote relay 格式不對. RD 確定. 60 ECS2020-08_114 3)DHCP recovery .5 種 desti 都是 0, RD 確定 61 ECS2020-08_115 ICMP response time is alwasy 0ms or 10ms .
PAGE 18
ENGINEERING RELEASE NOTES Compliance Level Compliant Known Anomalies: None. IEEE STANDARDS SUPPORT: Standard Title IEEE 802.1D Transparent Bridging Specifications (ISO/IEC 10038) IEEE 802.1p Traffic Class Expediting and Dynamic Multicast Filtering IEEE 802.1Q Virtual Bridged Local Area Networks IEEE 802.1w Rapid Spanning Tree IEEE 802.2 Local Area Networks, Logical Link Control (LLC) IEEE 802.3 CSMA/CD 9 (ISO/IEC 8802-3) IEEE 802.3I 10Base-T (ISO/IEC 8802-3, clause 14) IEEE 802.
PAGE 19
ENGINEERING RELEASE NOTES 802.
PAGE 20
ENGINEERING RELEASE NOTES - dnsServCounterNonAuthDatas - dnsServCounterNonAuthNoDatas - dnsServCounterReferrals - dnsServCounterErrors - dnsServCounterRelNames - dnsServCounterReqRefusals - dnsServCounterReqUnparses - dnsServCounterOtherErrors - dnsServOptCounter - dnsResMIBObjects - dnsResConfig - dnsResCounter - dnsResCache - dnsResCacheStatus - dnsResCacheMaxTTL - dnsResCacheGoodCaches - dnsResCacheBadCaches - dnsResOptCounter 3411 SNMP FrameWork - snmpFrameworkMIBO
PAGE 21
ENGINEERING RELEASE NOTES - tftpMgt - restartMgt - mirrorMgt - igmpSnoopMgt - ipMgt - bcastStormMgt - vlanMgt - priorityMgt - trapDestMgt - qosMgt - securityMgt - sysLogMgt - lineMgt ECS2020 PRIVATE ENTERPRISE MIB SUPPORT: Title Version ECS2020-Series.mib SNMP TRAP SUPPORT: RFC No.
PAGE 22
ENGINEERING RELEASE NOTES RFC 1757 risingAlarm (v1) fallingAlarm (v1) RFC 2819 risingAlarm (v2c) fallingAlarm (v2c) Customer Support: By Phone: By Email: By Web: By Fax: 6/2000 P/N: 9038023-04 Page: 22 of 6 F0615-E Subject to Change Without Notice