Users Manual

ManualsBrandsEdge-corE ManualsNetwork Hardware60GHz Access Point

– 1 –

Quick Start Guide

E112020-MR-R01

www.edge-core.com

60GHz Access Point

MLTG-CN

60GHz Access Point MLTG-CN

2. 1 x 24 W PoE injector

3. 1 x Power cord

4. 2 x Steel-band clamps for pole mount (3 inch diameter max.)

5. 2 x Screws with nylon expansion plugs for wall mount

6. Documentation QR-code card

Package Contents

1 2 3 4 6

Ground the MLTG-CN

Make Network Connections

Warning:

For a safe and reliable installation, use only the

accessories and screws provided with the device. Use of other

accessories and screws could result in damage to the unit. Any

damages incurred by using unapproved accessories are not

covered by the warranty.

Avertissement:

Pour une installation sûre et fiable, utilisez

uniquement les accessoires et les vis fournies avec l’appareil.

L’utilisation d’autres accessoires et vis pourrait endommager

l’appareil. Les dommages causés par l’utilisation d’accessoires

non approuvés ne sont pas couverts par la garantie.

Ground the MLTG-CN by connecting a ground wire to the grounding

point on the MLTG-CN and to nearby good earth.

Note:

The Uplink PoE port connection provides PoE power to

the unit.

RJ-45 Ports

1. Connect outdoor-rated Category 5e or better cable to the

1000BASE-T RJ-45 Uplink PoE port. Be sure to use the included

weatherproof RJ-45 port cover.

2. (Optional) Connect a local LAN switch or computer to the LAN

1000BASE-T RJ-45 port. Be sure to use the included weatherproof

RJ-45 port cover.

Overview

Installation

Integrated pole and wall mounting bracket.

2. System LED Indicators:

■

LAN: On (LAN port link), Blinking (activity).

■

Uplink(PoE): On (Uplink PoE port link), Blinking (activity).

Slow blink during system boot up.

■

60G: On (60GHz wireless link), Blinking (activity).

3. Grounding Screw: For ground wire connection.

4. LAN Port: Connects to LAN devices.

5. Uplink PoE Port: Connects to PoE injector and LAN devices.

Summary of content (4 pages)

PAGE 1
Quick Start Guide 60GHz Access Point MLTG-CN Package Contents 1 2 3 4 5 6 4. 2 x Steel-band clamps for pole mount (3 inch diameter max.) 5. 2 x Screws with nylon expansion plugs for wall mount 6. Documentation QR-code card 1. 60GHz Access Point MLTG-CN 2. 1 x 24 W PoE injector 3. 1 x Power cord Overview 1. Integrated pole and wall mounting bracket. 2. System LED Indicators: 1 ■ 2 3. 4. 5. 3 5 LAN: On (LAN port link), Blinking (activity).
PAGE 2
Quick Start Guide 3 Mount the MLTG-CN a. Mount on a Pole 4 Connect Power 1. Feed the steel-band clamps through the pole-mount bracket 2. points on the back of the MLTG-CN and then lightly fasten them around the pole. Align the MLTG-CN antenna with a nearby Distribution Node before tightening the clamps securely. b. Mount on a Wall Connect the other end of the outdoor-rated Ethernet cable from the Uplink (PoE) port to the 802.3at-compliant power injector. 5 Verify Power is On 1.
PAGE 3
Quick Start Guide 6 Access the Web User Interface 1. Connect a PC directly to the MLTG-CN’s LAN port. 2. Set the PC IP address to be on the same subnet as the MLTG-CN 3. 4. LAN port default IP address. The PC address must start 192.168.2.x with subnet mask 255.255.255.0). Enter the MLTG-CN’s default IP address of 192.168.2.1 into the web browser address bar.
PAGE 4
Quick Start Guide être installé et utilisé avec un minimum de 22 cm de distance entre la source de rayonnement et votre corps. Hardware Specifications AP Chassis CE Statement This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. All operational modes: 60 GHz: 802.11ad, 802.