Powered by Accton 5/8-Port Gigabit Switch ES4005V ES4008V Installation Guide www.edge-core.
Quick Installation Guide 5-Port Gigabit Ethernet Switch Gigabit Ethernet Switch with 5 10BASE-T / 100BASE-TX / 1000BASE-T (RJ-45) Ports 8-Port Gigabit Ethernet Switch Gigabit Ethernet Switch with 8 10BASE-T / 100BASE-TX / 1000BASE-T (RJ-45) Ports
ES4005V ES4008V E032005-R01 150000017400H
Contents Introduction Features and Benefits Front Panel RJ-45 Ports LEDs ES4005V ES4008V Rear Panel 1 1 1 2 2 2 2 Installing the Switch Package Contents Selecting a Site Instructions Applications 3 3 3 3 4 Product Specifications Physical Characteristics Switching Criteria 6 6 6 Troubleshooting Diagnosing Switch Indicators Power and Cooling Problems Installation 7 7 7 7 Cables Cable Specifications 10BASE-T/100BASE-TX Pin Assignments 1000BASE-T Pin Assignments 1000BASE-T Cable Requirements Cable Testi
Contents ii
Introduction These switches are high-performance Gigabit Ethernet switches designed for delivering Gigabit connectivity to the desktop. They provide 5/8 full-duplex 1000BASE-T ports that significantly improve network performance and boost throughput for high-bandwidth applications. With 10/16 Gigabits of aggregate bandwidth, these switches provide the quickest solution to meeting the growing demands on your network's limited resources.
Introduction LEDs The front panel of the switch provides status LEDs for “at-a-glance” system monitoring. The following table details the functions of the various indicators. LED Power Ports Link/Act Port and System Status LEDs Condition Status On The switch is receiving power. Off The switch is not receiving power. On Off 1000M Flashing On Off The port has established a valid network connection. The port has not established a network connection. Traffic is passing through the port.
Package Contents Installing the Switch Before installing the switch, verify that you have all the items listed under “Package Contents.” If any of the items are missing or damaged, contact your local Accton distributor. Also be sure you have all the necessary tools and cabling before installing the switch. Note that the switch can be installed on any suitable large flat suface.
Installing the Switch 3. Connecting PCs: Connect each PC to an RJ-45 port on the switch using Category 5, 5e, or 6 shielded or unshielded twisted-pair (UTP or STP) cable, maximum length 100 meters (328 ft). Switch 10/100/1000 will support up to 5/8 PCs. All ports on the switch support automatic MDI/MDI-X operation, so you can use straight-through cables for all network connections to PCs or servers, or to other switches or hubs.
Applications V 100 Mbps 10 Mbps 100 Mbps 1000 Mbps 100 Mbps Server 10 Mbps Workstations 100 Mbps Workstation 1000 Mbps Workstation Standalone LAN V V 100 Mbps Servers 100 Mbps Workstations 1000 Mbps Workstation 100 Mbps Server 1000 Mbps Workstation 10 Mbps Segment 100 Mbps Segment Cascading Switches 5
Product Specifications Product Specifications Physical Characteristics Standards Conformance Communication Rate Communication Mode Media Supported Number of Ports Indicator Panel Dimensions Weight DC Input Power Power Consumption Temperature Humidity Immunity Emissions Safety IEEE Std 802.3-2002 10.
Troubleshooting Diagnosing Switch Indicators Symptom Power LED does not light after power on. Probable Causes DC power adapter may be defective. Possible Solutions • Check for loose connections. • Check the power outlet by using it for another device. • Replace the DC power adapter. Symptom Port (link) LED does not light after connection is made. Probable Causes Switch port, network card or cable may be defective. Possible Solutions • Check that the switch and attached device are both powered on.
Cables Cable Specifications Cable Types and Specifications Cable Type Max. Length Connector 10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) RJ-45 100BASE-TX Cat. 5 100-ohm UTP 100 m (328 ft) RJ-45 1000BASE-T Cat. 5, 5e, 6 100-ohm UTP 100 m (328 ft) RJ-45 Caution: DO NOT plug a phone jack connector into any RJ-45 port. Use only twisted-pair cables with RJ-45 connectors that conform with FCC standards.
1000BASE-T Pin Assignments The table below shows the 1000BASE-T MDI and MDI-X port pinouts. These ports require that all four pairs of wires be connected. Note that for 1000BASE-T operation, all four pairs of wires are used for both transmit and receive. Use 100-ohm Category 5 or 5e unshielded twisted-pair (UTP) or shielded twistedpair (STP) cable for 1000BASE-T connections. Also be sure that the length of any twisted-pair connection does not exceed 100 meters (328 feet).
EMI Certification Adjusting Existing Category 5 Cabling If your existing Category 5 installation does not meet one of the test parameters for 1000BASE-T, there are basically three measures that can be applied to try to correct the problem: 1. 2. 3. Replace any Category 5 patch cables with high-performance Category 5e cables. Reduce the number of connectors used in the link. Reconnect some of the connectors in the link.
CE Mark Declaration of Conformance for EMI and Safety (EEC) This information technology equipment complies with the requirements of the Council Directive 89/336/EEC on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain voltage limits and the Amendment Directive 93/68/EEC.
Safety Compliance Safety Compliance Please read the following safety information carefully before installing the switch: Warning: Installation and removal of the unit must be carried out by qualified personnel only. Warning: Do not plug a phone jack connector in the RJ-45 port. This may damage this device. Achtung: Les raccordeurs ne sont pas utilisés pour le systéme téléphonique! Warning: This product does not contain any serviceable user parts.
ES4005V ES4008V E032005-R01 150000017400H
