Use and Care Manual

-Always ensure the heater is plugged into a suitable socket, one that is tested for outdoor use.
-To disconnect heater, turn controls to OFF, then remove plug from socket. Do not unplug by pulling on the power cable.
-Always unplug the unit and ensure the unit is completely cold before moving, cleaning or storing.
-This heater is intended for domestic use only and should not be used commercially for contract purposes. Any
alternative use, not recommended by the manufacturer, may result in fire, electric shock, or injury to persons.
-The use of attachments on the heater is not recommended.
-Warning: This heater is not equipped with a device to control the room temperature. Do not use this heater in small
rooms when occupied by persons not capable of leaving a room on their own, unless constant supervision is provided.
-Always use on a dry, suitably strong, stable, flat and level surface.
-Check exterior walls for communication and electrical cables and pipelines. Should any service lines be present in the
immediate vicinity do not install your heater, find an alternative location to install this product.
-Do not position directly above or below an electrical socket.
-Do not remove any of the warning stickers or signs from the product.
Important Instructions (Continued)
Parts List
1
3
5
7
9
10
8
6
4
2
11
Front Aluminum Cover
Left Housing
Left Decorative Cover
Back Aluminum Cover
Heating Tube
Power Cord
Right Housing
Right Decorative Cover
LED Display
Protection Grill
Decorative Support
1
5
4
6
8
9
10
11
7
2
3
Cleaning and Maintenance Instructions
Warnings
Attention! Careful and regular maintenance of infrared Heater is required to attain a long and efficient operation of your
appliance.
1. Check the cleanliness of the reflector and IR-filament at least once a month. If necessary, apply cleaning and
maintenance instructions.
2. The number of checks may be increased considering the amount of the dust in the environment.
3. Check the deformation of the reflector, wire and frame visually while cleaning the appliance. In case of any
deformation, consult a qualified technician.
4. Check the power cable and plug visually while cleaning the appliance. In case of any deformation, consult a qualified
technician.
5. It is recommended to change the reflector every 2 years for more efficient operation.
Cleaning
Attention! Regular and careful cleaning helps your heater operate for longer years and more efficiently.
1. Unplug your power cable for your safety before cleaning your appliance.
2. Take out the front grid wire through the inlets on the frame using a slotted screwdriver.
3. Make sure that the power is off for your safety. Power cable plug must be unplugged.
4. The reflector and filament must be cleaned with a soft cloth, a smooth brush or cool or dry air. The cloth may be
damp but never too wet and the cleaner should not include any chemical.
5. Refrain from using cleaning material likely to damage the reflector (cleanser etc.).
6. Insert the wire grid using a slotted screwdriver.
1 Do not place any objects such as furniture, papers, cloths, and curtains at least 0.9m (3 feet) from the front of the
heater and away from the sides and rear when the heater is plugged in.
2 Do not place the heater near a bed because objects such as pillows or blankets can fall off the bed and be ignited by the
heater.
3 Always unplug the heater if it is not being used.
4 Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire. However, if you
have to use an extension cord, the cord shall be 1.5mm² minimum size .Do not operate within 7.6 m (25 feet) of
flammable material.
Never block the front grill of the heater.
The heater is not suitable for hazardous locations.
Never attempt to service the heater without disconnecting its power source.
2.2 Safety Instructions (C+D+E)
C-The distance from bath tub, washbasin or other sanitary installations
You may operate your heater in the bathroom and outdoors considering the items below:
The distance of your appliance from bath tub, washbasin or other sanitary installations is to be min 0.6 m (2 feet). The
distance of 1 m (3.5 feet) is recommended for more safety.
The distance of the earthed plug from bath tub, washbasin or other sanitary installations must be min 0.6 m (2 feet).
1 m (3.5 feet) distance is recommended for more safety.
8
3