ELECTRIC STOVE HEATER OWNERS MANUAL 101001, 111001 Only use this heater as described in this manual. Any other use is not recommended by the manufacturer, and may cause fire, electric shock, or other personal injury. WARNING! Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure to do so could result in fire, electric shock, serious personal injury, or death.
IMPORTANT SAFETY INFORMATION! WARNING ⚫ ALWAYS keep electric cords, home furnishings, drapes, clothing, papers, or other combustibles at least 3 feet (0.9m) away from the front of this heater, and away from the bottom, sides, and rear of this heater. ⚫ ALWAYS attach the feet before using! NEVER plug in or operate this unit if the feet are not securely attached! ⚫ DO NOT place the heater near a bed because objects such as pillows or blankets can fall off the bed and be ignited by the heater.
WARNING ⚫ Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside! ⚫ ALWAYS disconnect this unit from the power supply before performing any assembly or cleaning, or before relocating the electric fireplace. ⚫ ALWAYS store this heater in a dry location. NEVER use the fireplace if it has become wet. ⚫ NEVER use this heater in bathrooms, laundry rooms, or any other location where the heater could fall into a bathtub or pool, become damp or come in contact with water.
PREPARATION ⚫ Remove all parts and hardware from the carton and place them on a clean, soft, and dry surface. Make sure all parts are dry, and the power cord and plug are not damaged. See IMPORTANT SAFETY INFORMATION on pages 2 and 3. ⚫ Compare the contents with the parts list to make sure nothing is missing. ⚫ Dispose of all packaging materials properly. ⚫ Please recycle whenever possible.
PARTS AND HARDWARE Item Description Qty A Stove 1 B Legs 4 C Screws 12 A C B ASSEMBLY INSTRUCTIONS ALWAYS make sure the unit is unplugged before beginning assembly! NEVER move or clean the heater, or change the bulb, while it is plugged in.
C C A 1) Carefully turn the STOVE (A) upside down and lay it on a clean soft surface. 2) Thread three SCREWS (C) through the holes in the leg, and into the stove frame. Partially tighten with a Phillips screwdriver. 3) Repeat Steps 2 and 3 for the other three legs. 4) Check the alignment and tighten all 12 screws securely with the screwdriver.
OPERATION NOTICE BUTTON When the heat function is used for the first time, a slight odor may be present. This is normal and should not occur again unless the heater is not used for an extended period of time. ACTION / FUNCTION 1. Press to turn on flame effect and enable heater. Heater switches will not work unless ON/OFF this switch is turned on. 2. Press again to shut off the power to all functions. LOW HEAT HIGH HEAT INDICATION / RESULT 1. Flame effect and power light on switch turn on.
Cleaning Metal: ⚫ Buff using a soft cloth, slightly dampened with a citrus oil-based product. ⚫ DO NOT use brass polish or household cleaners as these will damage the metal. Glass: • Use glass cleaner and dry thoroughly with a paper towel or lint-free cloth. • NEVER use abrasive cleansers or any cleaner that could scratch the surface. Plastic: • Wipe with a slightly damp cloth and a mild solution of dish soap and warm water. • NEVER use abrasive cleansers or any cleaner that could scratch the surface.
Limited Warranty J & J Global (Seller) warrants to the original Buyer only, that each product will be free from defects in material and workmanship for a period of one (1) year from date of purchase. SELLER’S SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP.
