Installation Manual

Catalog #2105, #7105
Brochure #63-0275
©2005 Edelbrock Corporation
Rev. 8/05 - RS/mc Page 2 of 12
Manifold 2105 (Non-Emissions) Continued:
Manifold 7105 (Non-Emissions):
• THROTTLE BRACKETS: Due to the design of Performer manifolds, the throttle and kickdown bracket on some vehicles may require
modification to fit.
• GASKETS: Do not use competition style intake gaskets for this street manifold. Due to material deterioration over time, internal leakage of
vacuum, oil, and coolant may occur.
A - Carburetor will work with non-EGR or pre-emission control systems.
B - Carburetor will work with EGRsystem.
H - Carburetor has provision for evaporative canister.
I - Carburetor has no provisions for evaporative canister.
K - Carburetor requires #8008 or #8024 stud, washer and nut kit. Determine proper length based on gasket thickness and your accessory
mounting requirements.
N - Carburetor accepts factory cruise control
O - Carburetor comes with manual choke. It can be converted to electric choke using kit #1478.
CARBURETOR REFERENCE PARTS REQUIRED FOR INSTALLATION
Thunder Series #1825 (650 cfm) A, I, K, N #1483 or 1844 throttle lever adapter
Thunder Series #1826 (650 cfm) A, I, K, N #1483 or 1844 throttle lever adapter
Performer #1407 (750 cfm) A, I, K, N, O #1483 or 1844 throttle lever adapter
Performer #1411 (750 cfm) A, I, K, N #1483 or 1844 throttle lever adapter
Performer #1412 (800 cfm) A, I, K, N, O #1483 or 1844 throttle lever adapter
Performer #1413 (800 cfm) A, I, K, N #1483 or 1844 throttle lever adapter
Thunder Series #1812 (800 cfm) A, I, K, N #1483 or 1844 throttle lever adapter
Thunder Series #1813 (800 cfm) A, I, K, N #1483 or 1844 throttle lever adapter
CARBURETOR REFERENCE PARTS REQUIRED FOR INSTALLATION
Performer #1407 (750 cfm) A, I, K, N, O #1483 or 1844 throttle lever adapter
Performer #1411 (750 cfm) A, I, K, N #1483 or 1844 throttle lever adapter
Performer #1412 (800 cfm) A, I, K, N, O #1483 or 1844 throttle lever adapter
Performer #1413 (800 cfm) A, I, K, N #1483 or 1844 throttle lever adapter
Thunder Series #1812 (800 cfm) A, I, K, N #1483 or 1844 throttle lever adapter
Thunder Series #1813 (800 cfm) A, I, K, N #1483 or 1844 throttle lever adapter
INTAKE MANIFOLD REFERENCE RECOMMENDED GASKET
2105, 7105 Edelbrock #7224 Port: 1.20” x 2.10”, .060” Thickness
NOTE: To ensure maximum performance and a proper seal, Edelbrock gaskets which are
specifically designed and manufactured for use with Edelbrock parts must be used.
• BEFORE INSTALLING THE INTAKE MANIFOLD: The water bypass tube needs to be installed into the water bypass hole in the front of the
intake manifold. Apply some liquid Teflon thread sealant to the inside surface of the water bypass hole and tap the water bypass tube into
the hole using a block of wood and a hammer. Be careful to drive the tube straight into the bypass hole to avoid bending or crushing the
tube. Test fit the intake manifold with the bypass tube installed to make sure the bypass tube and water pump are aligned properly and have
proper clearance between them. See “Intake Manifold Test Fit Procedure” listed below for instructions.
• DISTRIBUTOR AND PUSHROD INSTALLATION: Due to the close tolerance of the distributor and pushrod fit, test fit the intake manifold to
check for proper clearance. See “Intake Manifold Test Fit Procedure” listed below for instructions.