E-GMS10-I-03/00 Operators Instruction Manual GMS-10 NOTE: Shown with optional cart 10” Gasoline Powered Masonry Saw with Controlled Dust Operation 100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA Phone (301) 663-1600 • 1-800-638-3326 Fax (301) 663-1607 • 1-800-447-3326 Website: www.edcoinc.com • Email: sales@edcoinc.
E-GMS10-I-03/00 READ AND UNDERSTAND THE OPERATORS INSTRUCTION MANUAL THOROUGHLY BEFORE ATTEMPTING TO OPERATE THIS EQUIPMENT. Death or serious injury could occur if this machine is used improperly. SAFETY MESSAGES GENERAL INSTRUCTIONS SAFETY MESSAGES • Safety Instructions are proceeded by a graphic alert symbol of DANGER, WARNING, or CAUTION. Indicates an imminent hazard which, if not avoided, will result in death or serious injury.
E-GMS10-I-03/00 Equipment Instruction Manual EDCO Model GMS-10 Table of Contents Section Page Number Safety Guidelines..............................................................................................................4 Operation Instructions................................................................................................5-7 Maintenance.............................................................................................................8-10 Maintenance Schedule............
E-GMS10-I-03/00 Read and understand this Operator’s Instruction Manual, and the Engine Manufacturer’s Owner’s Manual before operating this equipment. Death of serious injury can result if this machine is used improperly. Safety Guidelines Eye and ear protection must be worn at all times while the GMS-10 is in use. During normal operation, sound pressure levels exceed 92dBA. Use only ANSI approved safety glasses to help prevent eye injury.
E-GMS10-I-03/00 Operating Instructions Diagrams shown with Honda Cyclone Dual-Filter Element Engine as an example. Consult the Engine Manufacturer’sOwner’s Manual for information on specific models. A. B. C. D. E. F. G. H. I. J. K. L. M. Spark Plug Lead Air Filter Vacuum Hook Up Water Tray Oil Drain Oil Plug/Dip Stick Engine Throttle Fuel Valve Lever Choke Cyclone Housing Table Lock Back Stop Right Angle Guide Bar N. O. P. Q. R. S. T. U. V. W. X. Y.
E-GMS10-I-03/00 Before Starting Engine: • Read and understand the instructions supplied by the engine manufacturer. • Familiarize yourself with all engine and saw controls. • Visually inspect the entire machine for damage or wear. Look for signs of oil or fuel leaks. Remove excess dirt or debris. Check that all nuts, bolts and screws are tightened.
E-GMS10-I-03/00 Starting the Engine: • Be sure blade is clear of item to be cut. • Determine that the recoil starter assembly turns freely, starter rope pulls easily, and the rope retracts properly. • Follow the instructions supplied in the engine manufacturer’s Owner’s Manual for starting engine. • Open the throttle and allow engine to reach operating temperature. Do not use the throttle as a means to match the specified blade speed to the arbor shaft speed.
E-GMS10-I-03/00 Disconnect spark plug lead before performing any maintenance on this machine. Maintenance Consult the Engine Manufacturer’s Owner’s Manual for more detailed engine maintenance instructions. Changing the Blade: • Inspect the new blade thoroughly before installing. Check for cracks, loose segments, worn or out-of-round arbor holes. Refer to the Rx for Diamond Blades pamphlet provided with your blade for more detailed information on inspecting blades.
E-GMS10-I-03/00 Belt Adjustment and Replacement: • Periodically check to be sure the belts are undamaged and that they are at the proper tension. Slipping belts will overheat causing the cutting speed to be limited and will shorten the life of the belts. Over-tensioned belts will shorten the life of the belts and bearings. • On new equipment and after installing new belts, be certain to re-tension the belts after the first 4 hours of use. New belts are stiff and require a break in period.
E-GMS10-I-03/00 Change Engine Oil: • Check Engine Oil before each operation. Open the filler cap and look at the dip stick. (Figure 16) Oil should be clearly visable both on the stick and in the cavity and should look fairly clean. Running the machine on dirty oil or when the oil is low will result in damage to the equipment. • Change the Engine Oil after every 50 hours of operation - or sooner as conditions require.
E-GMS10-I-03/00 Repairs are to be done by authorized EDCO Dealers only. Read and follow instructions in the Engine Manufacturer’s Owner’s Manual.
E-GMS10-I-03/00 LIMITED EQUIPMENT WARRANTY Equipment Development Company, Inc. herein referred to as EDCO warrants that each new unit manufactured by EDCO to be free from defects in material and workmanship in normal use and service for a period of (1) one year (except in the case of the cutter drum assembly on all model concrete asphalt planes, in which case the warranty period shall be 90 days) from date of shipment to the original retail or equipment rental center owner.
