Replacement Part List

ManualsBrandsEDCO ManualsMiscellaneous Parts8 in. Walk Behind Crete Planer/Scarifier with Honda 9 HP Gas Engine

E-CPM8-PL-0119

Page 1

800-638-3326 • edcoinc.com • techsupport@edcoinc.com

PARTS LIST MANUAL

MODEL CPM8

REVISED STARTING

SERIAL # 19010484

GASOLINE MODEL

8” WALK BEHIND CRETE-PLANERS®

SKU # MODEL # POWER OPTION

79300 CPM8-9H HONDA GASOLINE ENGINE MODEL GX270

79500 CPM8-5B/230/1 BALDOR ELECTRIC MOTOR 5HP 60Hz 1PH 230V

79400-230 CPM8-5B/230/3 BALDOR ELECTRIC MOTOR 5HP 60Hz 3PH 230V

79400-460 CPM8-5B/460/3 BALDOR ELECTRIC MOTOR 5HP 60Hz 3PH 460V

79400-50/220 CPM8-5B/50/220/3 BALDOR ELECTRIC MOTOR 5HP 50Hz 3PH 220V

79400-50/380 CPM8-5B/50/380/3 BALDOR ELECTRIC MOTOR 5HP 50Hz 3PH 380V

79400-50/440 CPM8-5B/50/440/3 BALDOR ELECTRIC MOTOR 5HP 50Hz 3PH 440V

ELECTRIC MODEL

Printed in USA

EQUIPMENT DEVELOPMENT COMPANY, INC.

100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA

Phone: 800-638-3326 or 301-663-1600 • Fax: 800-447-3326 or 301-663-1607

Website: www.edcoinc.com • E-mail: techsupport@edcoinc.com

READ AND UNDERSTAND THE OPERATOR’S SAFETY MANUAL THOROUGHLY

BEFORE ATTEMPTING TO OPERATE THIS EQUIPMENT.

Death or serious injury could occur if this machine is used improperly.

Machine specic Operator’s Instruction Manuals are o󰀨ered at edcoinc.com/customer-resources/manuals-parts-lists/

READ AND UNDERSTAND THE ENGINE MANUFACTURERS INSTRUCTIONS AND OPERATORS MANUAL BEFORE OPERATION.

Summary of content (36 pages)

PAGE 1
E-CPM8-PL-0119 REVISED STARTING SERIAL # 19010484 PARTS LIST MANUAL ® GASOLINE MODEL MODEL CPM8 ELECTRIC MODEL 8” WALK BEHIND CRETE-PLANERS® SKU # 79300 MODEL # CPM8-9H POWER OPTION HONDA GASOLINE ENGINE MODEL GX270 79500 CPM8-5B/230/1 BALDOR ELECTRIC MOTOR 5HP 60Hz 1PH 230V 79400-230 CPM8-5B/230/3 BALDOR ELECTRIC MOTOR 5HP 60Hz 3PH 230V 79400-460 CPM8-5B/460/3 BALDOR ELECTRIC MOTOR 5HP 60Hz 3PH 460V 79400-50/220 CPM8-5B/50/220/3 BALDOR ELECTRIC MOTOR 5HP 50Hz 3PH 220V 79400-50/380 CPM
PAGE 2
E-CPM8-PL-0119 SAFETY INFORMATION SAFETY MESSAGES • Safety Instructions are proceeded by a graphic alert symbol of DANGER, WARNING, or CAUTION. Indicates an imminent hazard which, if not avoided, will result in death or serious injury. Indicates an imminent hazard which, if not avoided, can result in death or serious injury. Indicates hazards which, if not avoided, could result in serious injury and or damage to the equipment.
PAGE 3
E-CPM8-PL-0119 PARTS LIST MANUAL MODEL CPM8 8” WALK BEHIND CRETE-PLANER® TABLE OF CONTENTS Section Page Number Safety Messages and General Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 How To Order Replacement Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Illustration 1: Main Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4, 5 Illustration 2: Rear Fork & Control Linkage Grouping . . . .
PAGE 4
E-CPM8-PL-0119 ILLUSTRATION 1: MAIN GROUPING 800-638-3326 • edcoinc.com • techsupport@edcoinc.
PAGE 5
E-CPM8-PL-0119 PARTS LISTING - ILLUSTRATION 1: MAIN GROUPING ITEM # PART # DESCRIPTION QTY. 1 65001 MAIN FRAME, CPM-8 1 2 65014 AXLE SHAFT 3/4”DIA. X 12-3/16”L 1 3 10428 COLLAR, LOCKING 3/4”ID 2 4 52001 WHEEL 4 X 1-1/2 X 3/4”BRG.
PAGE 6
E-CPM8-PL-0119 ILLUSTRATION 2: REAR FORK & CONTROL LINKAGE GROUPING 800-638-3326 • edcoinc.com • techsupport@edcoinc.
PAGE 7
E-CPM8-PL-0119 PARTS LISTING - ILLUSTRATION 2: REAR FORK & CONTROL LINKAGE GROUPING ITEM # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 PART # 14023 10411 50550 65019 85005 10073 65007 10359 79035 10127 10808 10096 65006 65004 65005 52001 10306 81001 10407 65015 10312 DESCRIPTION KNOB, BALL 1-3/8 W/ 1/2-13THD, BLK. SCREW, SKT. HD.
PAGE 8
E-CPM8-PL-0119 ILLUSTRATION 3: OPTIONAL WATER SYSTEM KIT PART # 65080 ITEM # PART # DESCRIPTION 1 10711A VALVE & HOSE CONNECTOR ASSY. (INCLUDES ITEMS 2 & 3) 1 2 10711 VALVE, BALL 1/2 FPT 1 3 80021 CONN., SWIVEL FEM. 3/4HOSE X 1/2MPT 1 4 56022 BRACKET, WATER VALVE 1 5 10038 WASHER, LOCK 1/4 ZINC 2 6 10846 SCREW, CAP STSHW 1/4-20 X 1/2 2 7 10799 BARB ELBOW 90, 3/8HOSE X 1/4MPT 1 8 10714 CLAMP, HOSE, SAE #4, ADJ.
PAGE 9
E-CPM8-PL-0119 ILLUSTRATION 4: RUBBER SEAL GROUPING ITEM # 1 PART # 65036-R 2 3 4 5 6 7 65152 65153 65151 65154 10018 10015 DESCRIPTION RUBBERS (SET OF 4), CPM-8 INCLUDES ITEMS 2 THRU 8) RUBBER DUST SKIRT, FRONT/REAR RUBBER DUST SKIRT RETAINER, FRONT/REAR RUBBER DUST SKIRT, SIDE RUBBER DUST SKIRT RETAINER, SIDES SCREW, CAP 1/4-20 X 3/4 NUT, HEX LOCK 1/4-20 ZINC QTY. 1 2 2 2 2 8 8 800-638-3326 • edcoinc.com • techsupport@edcoinc.
PAGE 10
E-CPM8-PL-0119 ILLUSTRATION 5: DRUM, SHAFT & BEARING GROUPING ITEM # 1 PART # 65050 2 3 4 65037 65039 65038A 5 65056 10961 65038 10113 10878 10873 65057 10808 10025 10811 10309 6 7 8 9 10 11 12 13 DESCRIPTION DRUM ASSY. COMP. CPM-8 CUTTER (REFER TO ILLUS. 6 FOR BREAKDOWN) DRUM SHAFT 18-3/8”L, CPL/M-8 NUT, HEX JAM 5/8-11 LEFT-HAND, ZINC DRIVER W/ BEARING ASSY., CPL/M-8 (INCLUDES ITEMS 5 THRU 9) BEARING ASSY. COMPLETE, 1-1/4”DIA.
PAGE 11
ILLUSTRATION 6: CUTTER DRUM ASSEMBLY E-CPM8-PL-0119 STANDARD - 8” WIDTH ITEM # PART # DESCRIPTION 1 65050C DRUM ASSY LOADED W/ CUTTERS CPM8 LOADED WITH 78 CP206T CUTTERS & 210 CG227 SPACERS 1 2* 65050 DRUM ASSY.
PAGE 12
E-CPM8-PL-0119 ILLUSTRATION 7: OPTIONAL EDGER ASSEMBLY PART # 65027 ITEM # PART # DESCRIPTION 65025 DRUM SHAFT, CPM-8 EDGER 1 2 10420 WASHER, LOCK 1/2 HEAVY-DUTY 1 3 10490 SCREW, SKT. HD. CAP 1/2-13 X 1 1 4 65026 FLANGE, DRIVER, CPM-8 EDGER 1 5 65028 PIN, WIRE LOCK 5/16”DIA. X 2.75”GRP 1 6 65039 NUT, JAM 5/8-11 LEFT-HAND THD.
PAGE 13
ILLUSTRATION 8: OPTIONAL EDGER CUTTER DRUM ASSEMBLY E-CPM8-PL-0119 4” WIDTH ITEM # PART # DESCRIPTION 1* C66040 DRUM ASSY. COMPLETE, CPM-4 CUTTER (INCLUDES ITEMS 2 THRU 6) 1 2 C66041 DRUM ONLY, CUTTER, CPM-4 1 3 65054 RETAINING PLATE, CUTTER SHAFT 1 4 10801 WASHER, LOCK 5/16 ZINC 3 5 10627 SCREW, SKT. BUTTON HD. 5/16-18 X3/4 3 6 C66043 CP410 SHAFT 1/2 X 5-3/16”L, CPM-4 6 7* 12230 8* CG227 SPACER 1/2”ID QTY. SEE NOTE CUTTERS: 20156 CP206T 6-PT.
PAGE 14
E-CPM8-PL-0119 ILLUSTRATION 9: OPTIONAL DIAMOND GROOVING HEAD ASSEMBLY 7” WIDTH NOTE: CUT DIRECTION IS MARKED ON EACH BLADE. ITEM # PART # 1* 65077 HEAD ASSY., DIAMOND GROOVING, CPM-8 (INCLUDES ITEM 2 THRU 5) 1 2 65070 ARBOR, DIAMOND GROOVING HEAD,CPM-8 1 3 65071 ARBOR BLADE CAP 6”, CPM-8 1 4 65075 WASHER, LOCK, INT. TOOTH 1-1/4” 1 5 65076 NUT, HEX JAM 1 1/4-12 1 65072 65073 65078 65074 SPACERS: 6”OD X 1-1/4”ID X .063 (MINIMUM BLADE SPACING) 6”OD X 1-1/4”ID X .
PAGE 15
1/2” DIAMOND GROOVING HEAD SET-UP WITH 3/32” THICK BLADES E-CPM8-PL-0119 1/2” CENTER-TO-CENTER SPACING (QTY. 15) 39808 .090”THK BLADES (QTY. 14) 65073 .430”THK SPACERS 11/16” DIAMOND GROOVING HEAD SET-UP WITH 3/32” THICK BLADES 11/16” CENTER-TO-CENTER SPACING (QTY. 11) 39808 .090”THK BLADES (QTY. 10) 65078 .625”THK SPACERS 800-638-3326 • edcoinc.com • techsupport@edcoinc.
PAGE 16
E-CPM8-PL-0119 1” DIAMOND GROOVING HEAD SET-UP WITH 3/32” THICK BLADES 1” CENTER-TO-CENTER SPACING (QTY. 8) 39808 .090”THK BLADES (QTY. 7) 65074 .930”THK SPACERS 5/8” DIAMOND GROOVING HEAD SET-UP WITH 3/32” THICK BLADES (PAIRED) 5/8” CENTER-TO-CENTER SPACING (QTY. 22) 39808 .090”THK BLADES (QTY. 11) 65072 .063”THK SPACERS (BETWEEN BLADES) (QTY. 11) 65073 .430”THK SPACERS (BETWEEN PAIRS) 800-638-3326 • edcoinc.com • techsupport@edcoinc.
PAGE 17
3/4” DIAMOND GROOVING HEAD SET-UP WITH 1/4” THICK BLADES E-CPM8-PL-0119 3/4” CENTER-TO-CENTER SPACING (QTY. 10) 39806 .250”THK BLADES (QTY. 9) 65155 .594”THK SPACERS CUSTOM SET-UPS CAN BE CREATED UPON REQUEST Specify spacing, thickness and a width that is 7 inches or less as shown below. 800-638-3326 • edcoinc.com • techsupport@edcoinc.
PAGE 18
E-CPM8-PL-0119 THIS PAGE WAS LEFT BLANK INTENTIONALLY 800-638-3326 • edcoinc.com • techsupport@edcoinc.
PAGE 19
E-CPM8-PL-0119 ILLUSTRATION 10: OPTIONAL LIFTING BAIL ASSEMBLY PART # 65096A ITEM # 1 2 3 4 PART # 65096 10029 10025 10058 DESCRIPTION BAIL ONLY, LIFTING SCREW, CAP 3/8-24 X 1-3/4 WASHER, FLAT 3/8 SAE ZINC NUT, HEX LOCK 3/8-24 W/ NYLON PATCH QTY. 1 4 8 4 INSTRUCTIONS FOR MOUNTING LIFTING BAIL 800-638-3326 • edcoinc.com • techsupport@edcoinc.
PAGE 20
E-CPM8-PL-0119 MODEL CPM8-9H ILLUSTRATION 11: ENGINE GROUPING 800-638-3326 • edcoinc.com • techsupport@edcoinc.
PAGE 21
E-CPM8-PL-0119 PARTS LISTING - ILLUSTRATION 11: ENGINE GROUPING ITEM # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PART # 15027 10625 10128 40328 10918 10056 10025 10213 10801 10054 10452 40388 10877 10831 10982 15201A 17 18 19 20 21 22 10968 10970 10553 10307 65045 10505 40317 81007 DESCRIPTION ENGINE, HONDA GX270UT2QC9 MUFFLER CAP, HONDA #18331-ZE3-811 RIVET, BLIND 1/8 X .250L X .
PAGE 22
E-CPM8-PL-0119 MODEL CPM8-5B/230/1 ILLUSTRATION 12: SINGLE PHASE MOTOR GROUPING 800-638-3326 • edcoinc.com • techsupport@edcoinc.
PAGE 23
E-CPM8-PL-0119 PARTS LISTING - ILLUSTRATION 12: SINGLE PHASE MOTOR GROUPING ITEM # PART # DESCRIPTION 1 81026 MOTOR, BALDOR 5HP-1PH 60HZ 3450RPM REPLACEMENT PARTS: CAPACITOR, START, BALDOR EC1161C06SP CAPACITOR, RUN, BALDOR #OC3040F09SP THERMAL PROT. (RESET BUTTON) TPBRT25DB 1 KEY 1/4”SQ. X 1-3/4 (INCLUDED W/ MOTOR) 1 16121 16164 16540 QTY.
PAGE 24
E-CPM8-PL-0119 ILLUSTRATION 13: THREE PHASE MOTOR GROUPING MODELS: CPM8-5B/230/3 CPM8-5B/460/3 CPM8-5B/50/220/3 CPM8-5B/50/380/3 CPM8-5B/50/440/3 PARTS LISTING - ILLUSTRATION 12: THREE PHASE MOTOR GROUPING ITEM # PART # DESCRIPTION 1 81022 16020 MOTOR, BALDOR 5HP-3PH-60HZ-230/460V MOTOR, BALDOR 5HP-3PH-50HZ-230/400V 1 1 2 ----- KEY 1/4”SQ X 1-3/4 (INCLUDED W/ MOTOR) 1 3 16660 16661 16662 16663 16664 16665 SWITCH BOX COMPLETE, ON/OFF/E-STOP ...
PAGE 25
E-CPM8-PL-0119 PARTS LISTING CONTINUED - ILLUS. 13: THREE PHASE MOTOR GROUPING ITEM # PART # DESCRIPTION QTY. 4 65088 BRACKET, REMOTE SWITCH, CPM-8 1 5 11663 SCREW, MACHINE 8-32 X 1/2 RHCD ZINC 4 6 10462 NUT, KEPS LOCK 8-32 ZINC 4 7 10846 SCREW, CAP STSHW 1/4-20 X 1/2 4 8 10038 WASHER, LOCK 1/4 ZINC 4 9 10790 CONDUIT LOCK NUT 1/2 NP (LOCATED INSIDE BOX) 1 10 16190 STRAIN RELIEF 1/2NPT X .250-.
PAGE 26
E-CPM8-PL-0119 SINGLE PHASE MODEL: CPM8-5B/230/1 WIRING DIAGRAM FOR ROTARY CAM SWITCH 60Hz 1-PHASE 230V 800-638-3326 • edcoinc.com • techsupport@edcoinc.
PAGE 27
SINGLE PHASE MODEL: CPM8-5B/230/1 E-CPM8-PL-0119 WIRING DIAGRAM FOR 60Hz 1-PHASE MOTOR BALDOR CAT. NO. L3608TM 5 H.P., 1 PHASE, 60 HERTZ, 3450 RPM, 230 VOLT, 19.5 FULL LOAD AMPS USE CONNECTIONS FOR OPPOSITE ROTATION SHOWN BELOW LINE “A” IS BLACK WIRE, LINE “B” IS WHITE WIRE CAPACITOR WIRING DETAIL P/N 16121 - START CAPACITORS 2 REQ’D. 161-193 MFD, 250V P/N 16164 - RUN CAPACITOR 1 REQ’D. 40 MFD, 370V 800-638-3326 • edcoinc.com • techsupport@edcoinc.
PAGE 28
E-CPM8-PL-0119 THREE PHASE MODELS: CPM8-5B/230/3, CPM8-5B/460/3, CPM8-5B/50/220/3, CPM8-5B/50/380/3 & CPM8-5B/50/440/3 WIRING DIAGRAM FOR STARTER & REMOTE SWITCH 800-638-3326 • edcoinc.com • techsupport@edcoinc.
PAGE 29
E-CPM8-PL-0119 MODELS: CPM8-5B/230/3 & CPM8-5B/460/3 WIRING DIAGRAM FOR 60Hz 3-PHASE MOTOR BALDOR CAT. NO. EM3613T 5 H.P., 3 PHASE, 60 HERTZ, 3450 RPM, 230/460 VOLTS, 12/6 FULL LOAD AMPS 800-638-3326 • edcoinc.com • techsupport@edcoinc.
PAGE 30
E-CPM8-PL-0119 MODEL CPM8-5B/50 WIRING DIAGRAM FOR 50Hz 3-PHASE MOTOR BALDOR CAT. NO. EM3613T-57 5 H.P., 3 PHASE, 50 HERTZ 800-638-3326 • edcoinc.com • techsupport@edcoinc.
PAGE 31
E-CPM8-PL-0119 MODEL CPM8-9H WIRING DIAGRAM FOR HONDA ENGINE 800-638-3326 • edcoinc.com • techsupport@edcoinc.
PAGE 32
E-CPM8-PL-0119 DECAL SHEET 800-638-3326 • edcoinc.com • techsupport@edcoinc.
PAGE 33
E-CPM8-PL-0119 RESET STOP START Light blue lines are reference cut lines only and are not to be printed. Created in Adobe Illustrator CS2 ROTATION ROTATION All text has been converted into outlines. All text referencing individual decal size or any other text will be removed from the decal sheet. The only text to remain other than what is inside of the light blue cut line on each decal is the EDCO PN: 92207.
PAGE 34
E-CPM8-PL-0119 NOTES Record here any repairs or changes made to the Equipment 800-638-3326 • edcoinc.com • techsupport@edcoinc.
PAGE 35
E-CPM8-PL-0119 LIMITED EQUIPMENT WARRANTY OF SALE Equipment Development Company, Inc.
PAGE 36
E-CPM8-PL-0119 BEFORE USING THIS PRODUCT Have You Used EDCO’s Online Customer Support?? Scan This QRC or Visit www.edcoinc.com/customer-support READ: EDCO Owner’s Manuals and Parts Listings share basic information and parts of each product. Download and print them whenever needed. WATCH: EDCO Product Training Videos show how to use products, install tooling, and perform basic maintenance. FIND: Somewhere on this product is an EDCO QRC Training Decal.