E-BB14E&BB14G-I-0714 E-SPTS-I-0809 EQUIPMENT DEVELOPMENT CO., INC. Operator’s Instruction Manual Masonry Saws BB14G BB14E Shown with Optional Pro Cart Shown with Optional Stand GASOLINE AND ELECTRIC 14” MASONRY SAWS EQUIPMENT DEVELOPMENT CO., INC. 100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA Phone: 301-638-3326 • 301-663-1600 Fax: 800-447-3326 • 301-663-1607 edcoinc.com • sales@edcoinc.
E-BB14E&BB14G-I-0714 EQUIPMENT DEVELOPMENT CO., INC. READ AND UNDERSTAND THE OPERATORS INSTRUCTION MANUAL THOROUGHLY BEFORE ATTEMPTING TO OPERATE THIS EQUIPMENT. Death or serious injury could occur if this machine is used improperly. SAFETY MESSAGES SAFETY MESSAGES • Safety Instructions are proceeded by a graphic alert symbol of DANGER, WARNING, or CAUTION. Indicates an imminent hazard which, if not avoided, will result in death or serious injury.
E-BB14E&BB14G-I-0714 E-SPTS-I-0809 EQUIPMENT DEVELOPMENT CO., INC. Table of Contents Section Page Number Operator Controls ................................................................................................................... 4-5 Safety Guidelines. ..................................................................................................................... 6 Operating Instructions ........................................................................................................
E-BB14E&BB14G-I-0714 EQUIPMENT DEVELOPMENT CO., INC. Operator Controls - Gas Models BB14 Gas (Figure 2) A B. C. D. E. F. G. H. I. J. K. L. M. N. O. P.
E-BB14E&BB14G-I-0714 E-SPTS-I-0809 J EQUIPMENT DEVELOPMENT CO., INC. Operator Controls- Electric Models K G A I BB14 Electric (Figure 4) C B D J L N E H F M A. B. C. D. E. F. G. H. I. J. K. L. M. N.
E-BB14E&BB14G-I-0714 EQUIPMENT DEVELOPMENT CO., INC. Read and understand this Operator’s Instruction Manual, and the Engine Manufacturer’s Owner’s Manual before operating this equipment. Death of serious injury can result if this machine is used improperly. Safety Guidelines Eye and ear protection must be worn at all times while the saw is in use. During normal operation, sound pressure levels exceed 85dBA. Use only ANSI approved safety glasses to help prevent eye injury.
E-BB14E&BB14G-I-0714 E-SPTS-I-0809 EQUIPMENT DEVELOPMENT CO., INC. Operating Instructions Before Starting: • Read and understand the instructions supplied by the engine manufacturer. • Familiarize yourself with all engine and saw controls. (Figure 2) • Visually inspect the entire machine for damage or wear. Look for signs of oil or fuel leaks. Remove excess dirt or debris. Check that all nuts, bolts and screws are tight.
E-BB14E&BB14G-I-0714 EQUIPMENT DEVELOPMENT CO., INC. When Wet Cutting: • Secure the drain plug and fill the tray with clean water. On Gasoline Models: • To engage water pump loosen the black knob and push top of water pump to the left with constant pressure and tighten black knob. (Figure 9 & 12) • Prime the pump using the priming bulb. Pump the bulb until water fills the clear plastic coolant hose from the tray to the pump.
E-BB14E&BB14G-I-0714 E-SPTS-I-0809 EQUIPMENT DEVELOPMENT CO., INC. When Dry Cutting: • Drain and flush any water or debris in the tray and dispose of properly. On Gasoline models: • To disengage water pump loosen the black knob and push top of water pump to the right with constant pressure and tighten black knob. (Figures 9 & 12) On Electric Models: • Unplug the submersible pump from the water pump outlet on the motor.
E-BB14E&BB14G-I-0714 EQUIPMENT DEVELOPMENT CO., INC. Starting the Engine: • Be sure blade is clear of item to be cut. • Determine that the recoil starter assembly turns freely, starter rope pulls easily, and the rope retracts properly. • Follow the instructions supplied in the Engine Manufacturer’s Owner’s Manual for starting engine. • Open the throttle and allow engine to reach operating temperature.
E-BB14E&BB14G-I-0714 E-SPTS-I-0809 EQUIPMENT DEVELOPMENT CO., INC. Cutting: • Do not strain the engine/motor while cutting. Do not jam work piece into the blade. Do not twist the work piece while cutting. • When you have finished cutting: On Gasoline models: To stop engine, return throttle to idle. Stop the engine by turning the engine mounted stop switch to the OFF position. Do not leave the saw running unattended. On electric models: Turn the power switch to OFF.
E-BB14E&BB14G-I-0714 EQUIPMENT DEVELOPMENT CO., INC. Disconnect spark plug lead before performing any maintenance on this machine. Maintenance Consult the Engine Manufacturer’s Owner’s Manual for more detailed engine maintenance instructions. Changing the Blade: • Inspect the new blade thoroughly before installing. Check for cracks, loose or missing segments, worn or out-ofround arbor holes.
E-BB14E&BB14G-I-0714 E-SPTS-I-0809 EQUIPMENT DEVELOPMENT CO., INC. Belt Adjustment and Replacement: • Periodically check belt(s) for damage, same type and are at the proper tension. Do not mix belts. Slipping belt(s) will overheat causing the cutting speed to be limited and shorten the life of the belts. Over-tensioned belts will shorten the life of the belt(s) and bearings.
E-BB14E&BB14G-I-0714 EQUIPMENT DEVELOPMENT CO., INC. Grease Bearings: • Drive shaft bearings must be greased every 4 hours. (All are not visible in this photo) • Electric Motor - if your motor has a grease fitting, grease every 3600 hours. Use Exxon Mobil Polyrex EM. Don not over grease. Apply 1 pump slowly taking a minute to apply. Too much grease can cause premature bearing failure. Grease Fittings Figure 23 Change Engine Oil: • Check Engine Oil before each operation.
E-BB14E&BB14G-I-0714 E-SPTS-I-0809 EQUIPMENT DEVELOPMENT CO., INC. Repairs are to be preformed by EDCO or by approved EDCO repair technicians. Read and follow all instructions in the Engine Manufacturer’s Owner’s Manual.
E-BB14E&BB14G-I-0714 EQUIPMENT DEVELOPMENT CO., INC.
E-BB14E&BB14G-I-0714 E-SPTS-I-0809 EQUIPMENT DEVELOPMENT CO., INC.
E-BB14E&BB14G-I-0714 EQUIPMENT DEVELOPMENT CO., INC. SMI Dust and Silica Warning Grinding/cutting/drilling of masonry, concrete, metal and other materials can generate dust, mists and fumes containing chemicals known to cause serious or fatal injury or illness, such as respiratory disease, cancer, birth defects or other reproductive harm.
E-BB14E&BB14G-I-0714 E-SPTS-I-0809 EQUIPMENT DEVELOPMENT CO., INC. LIMITED EQUIPMENT WARRANTY OF SALE – TERMS & CONDITIONS Equipment Development Company, Inc.
E-SPTS-I-0809 EQUIPMENT DEVELOPMENT CO., INC. SURFACE PREPARATION, RESORATION, PROFESSIONAL SAWING EQUIPMENT & HAND HELD TOOLS 100 THOMAS JOHNSON DRIVE, FREDERICK, MD 21702 PHONE: 800-638-3326 OR 301-663-1600 Fax: 800-447-3326 or 301-663-1607 Email: sales@edcoinc.com Website: edcoinc.com Patents Pending & Issued Created 6 2014 Printed in USA ©2014 800-638-3326 • edcoinc.com • sales@edcoinc.
