User's Manual

ManualsBrandsEDAN INSTRUMENTS ManualsElectronicsTelemetry Transmitter

Table Of Contents

Statement
Responsibility of the Manufacturer
Terms Used in this Manual
Chapter 1 Intended Use and Safety Guidance
- 1.1 Intended Use/Indications for Use
- 1.2 Safety Guidance
- 1.3 Explanation of Symbols on the Telemetry transmitter
Chapter 2 Overview
- 2.1 System Introduction
- 2.2 Display Screen of Telemetry Transmitter
- 2.3 Appearance of Telemetry Transmitter
- 2.4 Configuration
- 2.5 Display Screens of the MFM-CMS
Chapter 3 Installation of Telemetry Monitoring System
- 3.1 Initial Inspection
- 3.2 Installation Environment
- 3.3 Power Supply Requirement
- 3.4 Wireless Network
- 3.5 Installation Method
- 3.6 Checking the Printer
- 3.7 Checking the Telemetry Monitoring System
- 3.8 Setting Date and Time
- 3.9 Handing Over the Central Monitoring Systerm
- 3.10 FCC Statement
Chapter 4 Basic Operations
- 4.1 Basic Operations for Telemetry Transmitter
- 4.2 Basic Operations for MFM-CMS
  - 4.2.1 Mouse Operation
  - 4.2.2 Switching on/off the MFM-CMS
Chapter 5 Patient Management
- 5.1 Admitting a Patient
- 5.2 Changing Patient Information
- 5.3 Switching Patient sector
- 5.4 Discharging a Patient
- 5.5 Transferring a Patient
- 5.6 Monitoring Statistics
- 5.7 Nurse Call / Patient Call
Chapter 6 Patient Sector
- 6.1 Overview
- 6.2 Networked Monitoring Display
- 6.3 Menu in the Patient Sector
- 6.4 Parameter/ Waveform Setup
  - 6.4.1 Setting Waveforms
  - 6.4.2 Setting Parameters
- 6.5 Freeze
- 6.6 Real-Time Printing
- 6.7 Alarm Reset
Chapter 7 Viewing Single Bed
- 7.1 Display of Single Bed
- 7.2 Hiding/Showing Multi-Lead Waveform
- 7.3 Short Trend Review
- 7.4 OxyCRG
- 7.5 Freeze
Chapter 8 Setting Telemetry Transmitters via MFM-CMS
- 8.1 Changing Patient Information
- 8.2 Setting Parameters
  - 8.2.1 Parameters Alarm Setting
  - 8.2.2 Physiological Parameter Attribute and Configuration
Chapter 9 Review
- 9.1 Patient List
- 9.2 Wave Review
- 9.3 Alarm Review
- 9.4 Trend Review
Chapter 10 System Setup
- 10.1 Common Setup
- 10.2 User Maintain
Chapter 11 Alarm Management
- 11.1 Overview
- 11.2 Alarm Levels
- 11.3 Parameters Alarm Setting
- 11.4 Alarm Mute
- 11.5 Audio Pause
- 11.6 Alarm Prompt/Response
- 11.7 Testing Alarms
- 11.8 Alarms for Networking Status
Chapter 12 Alarm Information
- 12.1 Physiological Alarm Information
- 12.2 Technical Alarm Information
- 12.3 Prompts
- 12.4 Adjustable Range of Alarm Limits
Chapter 13 Printing
- 13.1 Printing Report with a Printer
- 13.2 Printing Preview/ Printing Settings
  - 13.2.1 Printing Preview
  - 13.2.2 Printing Settings
- 13.3 Exporting the PDF File
Chapter 14 Database Management
- 14.1 Database Backup
- 14.2 Reviewing Backup Database
Chapter 15 Monitoring ECG
- 15.1 Overview
- 15.2 ECG Safety Information
- 15.3 ECG Display
  - 15.3.1 ECG Display on Telemetry Transmitter Screen
  - 15.3.2 ECG Display on MFM-CMS
- 15.4 Selecting Calculation Lead
- 15.5 Changing Size of ECG Waveform
- 15.6 Changing ECG Filter Settings
- 15.7 ECG Alarm Settings
- 15.8 Monitoring Procedure
  - 15.8.1 Preparation
  - 15.8.2 Connecting ECG Cables
- 15.9 Installing Electrodes
  - 15.9.1 Electrode Placement for 3-lead
  - 15.9.2 Electrode Placement for 5-lead
- 15.10 Setting Alarm Source
- 15.11 Smart Lead Off
- 15.12 Setting Pace Status
- 15.13 ECG Calibration
- 15.14 ECG Waveform Settings
- 15.15 ST Segment Monitoring
- 15.16 Arr. Monitoring
  - 15.16.1 Arrhythmia Analysis
  - 15.16.2 ARR Analysis Menu
Chapter 16 Monitoring RESP
- 16.1 Overview
- 16.2 RESP Safety Information
- 16.3 Electrode Placement for Monitoring RESP
- 16.4 Cardiac Overlay
- 16.5 Chest Expansion
- 16.6 Abdominal Breathing
- 16.7 Selecting RESP Lead
- 16.8 Changing the Apnea Time
- 16.9 Changing the Size and Speed of the Respiration Waveform
- 16.10 RESP Alarm Settings
Chapter 17 Monitoring SpO2
- 17.1 Overview
- 17.2 SpO2 Safety Information
- 17.3 Measuring SpO2
- 17.4 Measurement Procedure
- 17.5 Assessing the Validity of a SpO2 Reading
- 17.6 SpO2 Alarm Delay
- 17.7 Setting Sensitivity
- 17.8 SpO2 Alarm Settings
Chapter 18 Monitoring PR
- 18.1 Overview
- 18.2 Selecting the Active Alarm Source
- 18.3 PR Alarm Settings
Chapter 19 Using Battery
- 19.1 Battery Status on Screen
- 19.2 Replacing the Battery
- 19.3 Recycling the Battery
Chapter 20 Safety
- 20.1 Control and Safety Index
- 20.2 Characteristics
Chapter 21 Care and Cleaning
- 21.1 General Points
- 21.2 Cleaning
  - 21.2.1 Cleaning the Telemetry Transmitter
  - 21.2.2 Cleaning the Reusable Accessories
- 21.3 Disinfection
  - 21.3.1 Disinfecting the Telemetry Transmitter
  - 21.3.2 Disinfecting the Reusable Accessories
Chapter 22 Maintenance
- 22.1 Inspecting
- 22.2 Maintenance Task and Test Schedule
Chapter 23 Warranty and Service
- 23.1 Warranty
- 23.2 Contact information
Chapter 24 Accessories
- 24.1 ECG Accessories
- 24.2 SpO2 Accessories
- 24.3 Other Accessories
A Product Specifications
- A.1 Classification of Telemetry Transmitter
- A.2 Specifications of Telemetry Transmitter
- A.3 Data Storage
- A.4 Specifications of MFM-CMS
  - A.4.1 Recommended Hardware Configuration
  - A.4.2 Software Performance
- A.5 ECG
- A.6 RESP
- A.7 SpO2
- A.8 Wi-Fi
B EMC Information
- B.1 Electromagnetic Emissions
- B.2 Electromagnetic Immunity
- B.3 Electromagnetic Immunity
- B.4 Recommended Separation Distances
C Default Settings
- C.1 Patient Information Default Settings
- C.2 Alarm Default Settings (MFM-CMS)
- C.3 ECG Default Settings
- C.4 RESP Default Settings
- C.5 SpO2 Default Settings
- C.6 PR Default Settings
D Abbreviation

Telemetry Transmitter User Manual Monitoring ECG

To change the smart lead off setting, enter the Parameter Setup Window (way to entering refers to 8.2

Setting Parameters)

> Click ECG on the left physiological parameter list > Choose Smart

LeadOff > Click Update Monitor to confirm.

15.12 Setting Pace Status

Setting pace status is operated on MFM-CMS.

It is important to set the paced status correctly when you start monitoring ECG. To change the

paced status in the ECG Setup menu, enter the Parameter Setup Window (way to entering refers to 8.2

Setting Parameters)

> Click ECG on the left physiological parameter list > Choose Pace > Click

Update Monitor to confirm.

When Pace is set to On:

- Pace Pulse Rejection is switched on. This means that pacemaker pulses are not counted as

extra QRS complexes.

- Paced symbol is displayed as

on the main screen.

NOTE:

1 When monitoring a patient with a pacemaker, set Pace to On. If monitoring a patient

without a pacemaker, set Pace to Off.

2 If Pace is set to On, the system will not perform some types of ARR analysis.

WARNING

Some pace pulses can be difficult to reject. When this happens, the pulses are counted

as a QRS complex, and could result in an incorrect HR and failure to detect cardiac arrest

or some arrhythmias. Keep pacemaker patients under close observation.

15.13 ECG Calibration

ECG calibration is operated on MFM-CMS. This item is used to calibrate ECG waveform.

To calibrate ECG, enter the Parameter Setup Window (way to entering refers to 8.2 Setting Parameters) >

Click ECG on the left physiological parameter list > Click Calibration to calibrate ECG

waveform. Then click Stop to end calibration.

NOTE:

The device can’t be monitored during ECG calibration.

15.14 ECG Waveform Settings

ECG waveform setting is operated on MFM-CMS and is applicable to the wave on MFM-CMS.

User can select an appropriate setting. The bigger the value is, the wider the waveform is.

6.25mm/s, 12.5mm/s, 25mm/s, 50mm/s are optional. Please refer to 6.4.1 Setting Waveforms for

more information.

- 79 -