User's Manual

ManualsBrandsEDAN INSTRUMENTS ManualsElectronicsTelemetry Transmitter

Table Of Contents

Statement
Responsibility of the Manufacturer
Terms Used in this Manual
Chapter 1 Intended Use and Safety Guidance
- 1.1 Intended Use/Indications for Use
- 1.2 Safety Guidance
- 1.3 Explanation of Symbols on the Telemetry transmitter
Chapter 2 Overview
- 2.1 System Introduction
- 2.2 Display Screen of Telemetry Transmitter
- 2.3 Appearance of Telemetry Transmitter
- 2.4 Configuration
- 2.5 Display Screens of the MFM-CMS
Chapter 3 Installation of Telemetry Monitoring System
- 3.1 Initial Inspection
- 3.2 Installation Environment
- 3.3 Power Supply Requirement
- 3.4 Wireless Network
- 3.5 Installation Method
- 3.6 Checking the Printer
- 3.7 Checking the Telemetry Monitoring System
- 3.8 Setting Date and Time
- 3.9 Handing Over the Central Monitoring Systerm
- 3.10 FCC Statement
Chapter 4 Basic Operations
- 4.1 Basic Operations for Telemetry Transmitter
- 4.2 Basic Operations for MFM-CMS
  - 4.2.1 Mouse Operation
  - 4.2.2 Switching on/off the MFM-CMS
Chapter 5 Patient Management
- 5.1 Admitting a Patient
- 5.2 Changing Patient Information
- 5.3 Switching Patient sector
- 5.4 Discharging a Patient
- 5.5 Transferring a Patient
- 5.6 Monitoring Statistics
- 5.7 Nurse Call / Patient Call
Chapter 6 Patient Sector
- 6.1 Overview
- 6.2 Networked Monitoring Display
- 6.3 Menu in the Patient Sector
- 6.4 Parameter/ Waveform Setup
  - 6.4.1 Setting Waveforms
  - 6.4.2 Setting Parameters
- 6.5 Freeze
- 6.6 Real-Time Printing
- 6.7 Alarm Reset
Chapter 7 Viewing Single Bed
- 7.1 Display of Single Bed
- 7.2 Hiding/Showing Multi-Lead Waveform
- 7.3 Short Trend Review
- 7.4 OxyCRG
- 7.5 Freeze
Chapter 8 Setting Telemetry Transmitters via MFM-CMS
- 8.1 Changing Patient Information
- 8.2 Setting Parameters
  - 8.2.1 Parameters Alarm Setting
  - 8.2.2 Physiological Parameter Attribute and Configuration
Chapter 9 Review
- 9.1 Patient List
- 9.2 Wave Review
- 9.3 Alarm Review
- 9.4 Trend Review
Chapter 10 System Setup
- 10.1 Common Setup
- 10.2 User Maintain
Chapter 11 Alarm Management
- 11.1 Overview
- 11.2 Alarm Levels
- 11.3 Parameters Alarm Setting
- 11.4 Alarm Mute
- 11.5 Audio Pause
- 11.6 Alarm Prompt/Response
- 11.7 Testing Alarms
- 11.8 Alarms for Networking Status
Chapter 12 Alarm Information
- 12.1 Physiological Alarm Information
- 12.2 Technical Alarm Information
- 12.3 Prompts
- 12.4 Adjustable Range of Alarm Limits
Chapter 13 Printing
- 13.1 Printing Report with a Printer
- 13.2 Printing Preview/ Printing Settings
  - 13.2.1 Printing Preview
  - 13.2.2 Printing Settings
- 13.3 Exporting the PDF File
Chapter 14 Database Management
- 14.1 Database Backup
- 14.2 Reviewing Backup Database
Chapter 15 Monitoring ECG
- 15.1 Overview
- 15.2 ECG Safety Information
- 15.3 ECG Display
  - 15.3.1 ECG Display on Telemetry Transmitter Screen
  - 15.3.2 ECG Display on MFM-CMS
- 15.4 Selecting Calculation Lead
- 15.5 Changing Size of ECG Waveform
- 15.6 Changing ECG Filter Settings
- 15.7 ECG Alarm Settings
- 15.8 Monitoring Procedure
  - 15.8.1 Preparation
  - 15.8.2 Connecting ECG Cables
- 15.9 Installing Electrodes
  - 15.9.1 Electrode Placement for 3-lead
  - 15.9.2 Electrode Placement for 5-lead
- 15.10 Setting Alarm Source
- 15.11 Smart Lead Off
- 15.12 Setting Pace Status
- 15.13 ECG Calibration
- 15.14 ECG Waveform Settings
- 15.15 ST Segment Monitoring
- 15.16 Arr. Monitoring
  - 15.16.1 Arrhythmia Analysis
  - 15.16.2 ARR Analysis Menu
Chapter 16 Monitoring RESP
- 16.1 Overview
- 16.2 RESP Safety Information
- 16.3 Electrode Placement for Monitoring RESP
- 16.4 Cardiac Overlay
- 16.5 Chest Expansion
- 16.6 Abdominal Breathing
- 16.7 Selecting RESP Lead
- 16.8 Changing the Apnea Time
- 16.9 Changing the Size and Speed of the Respiration Waveform
- 16.10 RESP Alarm Settings
Chapter 17 Monitoring SpO2
- 17.1 Overview
- 17.2 SpO2 Safety Information
- 17.3 Measuring SpO2
- 17.4 Measurement Procedure
- 17.5 Assessing the Validity of a SpO2 Reading
- 17.6 SpO2 Alarm Delay
- 17.7 Setting Sensitivity
- 17.8 SpO2 Alarm Settings
Chapter 18 Monitoring PR
- 18.1 Overview
- 18.2 Selecting the Active Alarm Source
- 18.3 PR Alarm Settings
Chapter 19 Using Battery
- 19.1 Battery Status on Screen
- 19.2 Replacing the Battery
- 19.3 Recycling the Battery
Chapter 20 Safety
- 20.1 Control and Safety Index
- 20.2 Characteristics
Chapter 21 Care and Cleaning
- 21.1 General Points
- 21.2 Cleaning
  - 21.2.1 Cleaning the Telemetry Transmitter
  - 21.2.2 Cleaning the Reusable Accessories
- 21.3 Disinfection
  - 21.3.1 Disinfecting the Telemetry Transmitter
  - 21.3.2 Disinfecting the Reusable Accessories
Chapter 22 Maintenance
- 22.1 Inspecting
- 22.2 Maintenance Task and Test Schedule
Chapter 23 Warranty and Service
- 23.1 Warranty
- 23.2 Contact information
Chapter 24 Accessories
- 24.1 ECG Accessories
- 24.2 SpO2 Accessories
- 24.3 Other Accessories
A Product Specifications
- A.1 Classification of Telemetry Transmitter
- A.2 Specifications of Telemetry Transmitter
- A.3 Data Storage
- A.4 Specifications of MFM-CMS
  - A.4.1 Recommended Hardware Configuration
  - A.4.2 Software Performance
- A.5 ECG
- A.6 RESP
- A.7 SpO2
- A.8 Wi-Fi
B EMC Information
- B.1 Electromagnetic Emissions
- B.2 Electromagnetic Immunity
- B.3 Electromagnetic Immunity
- B.4 Recommended Separation Distances
C Default Settings
- C.1 Patient Information Default Settings
- C.2 Alarm Default Settings (MFM-CMS)
- C.3 ECG Default Settings
- C.4 RESP Default Settings
- C.5 SpO2 Default Settings
- C.6 PR Default Settings
D Abbreviation

Telemetry Transmitter User Manual Printing

Chapter 13 Printing

The contents related to this chapter are all operated on MFM-CMS.

13.1 Printing Report with a Printer

MFM-CMS can output the reports by equipped with a laser printer. HP LaserJet Series printers

are recommended. The laser printer working with the MFM-CMS is independent of the

mainframe. The printer has its independent power supply. It is connected to the mainframe via a

USB interface or a network (wired or wireless).

The laser printer generates the following types of printing:

 Waveform review printing

 Alarm wave printing

 Alarm table printing

 Trend graph printing

 Trend table printing

 Printing for drug calculation, hemodynamic calculation, oxygenation calculation, renal

function calculation and ventilation calculation

 Patient information printing

NOTE:

MFM-CMS only supports printing on A4 paper.

13.2 Printing Preview/ Printing Settings

13.2.1 Printing Preview

Before the reports are printed, you can preview them on the screen. You will access the preview

interface after you select the function of printing. If a report consists of more than one page, you

may select a certain page to preview by turning to the page you want. Besides, you can adjust the

zoom setting by choosing a certain option from the drop-down list of the SIZE.

13.2.2 Printing Settings

Click on Print on the preview interface, and in the Print setup menu select the printer, the print

range and the number of copies in demand and then click on OK to confirm it.

13.3 Exporting the PDF File

MFM-CMS can export the PDF file by installing a PDF printer software. The software

PDFCreator is recommended. You can obtain the installation version of PDFCreator in the

MFM-CMS installation disk. Also, you may download it from the website

- 68 -