User's Manual

ManualsBrandsEDAN INSTRUMENTS ManualsElectronicsTelemetry Transmitter

Table Of Contents

Statement
Responsibility of the Manufacturer
Terms Used in this Manual
Chapter 1 Intended Use and Safety Guidance
- 1.1 Intended Use/Indications for Use
- 1.2 Safety Guidance
- 1.3 Explanation of Symbols on the Telemetry transmitter
Chapter 2 Overview
- 2.1 System Introduction
- 2.2 Display Screen of Telemetry Transmitter
- 2.3 Appearance of Telemetry Transmitter
- 2.4 Configuration
- 2.5 Display Screens of the MFM-CMS
Chapter 3 Installation of Telemetry Monitoring System
- 3.1 Initial Inspection
- 3.2 Installation Environment
- 3.3 Power Supply Requirement
- 3.4 Wireless Network
- 3.5 Installation Method
- 3.6 Checking the Printer
- 3.7 Checking the Telemetry Monitoring System
- 3.8 Setting Date and Time
- 3.9 Handing Over the Central Monitoring Systerm
- 3.10 FCC Statement
Chapter 4 Basic Operations
- 4.1 Basic Operations for Telemetry Transmitter
- 4.2 Basic Operations for MFM-CMS
  - 4.2.1 Mouse Operation
  - 4.2.2 Switching on/off the MFM-CMS
Chapter 5 Patient Management
- 5.1 Admitting a Patient
- 5.2 Changing Patient Information
- 5.3 Switching Patient sector
- 5.4 Discharging a Patient
- 5.5 Transferring a Patient
- 5.6 Monitoring Statistics
- 5.7 Nurse Call / Patient Call
Chapter 6 Patient Sector
- 6.1 Overview
- 6.2 Networked Monitoring Display
- 6.3 Menu in the Patient Sector
- 6.4 Parameter/ Waveform Setup
  - 6.4.1 Setting Waveforms
  - 6.4.2 Setting Parameters
- 6.5 Freeze
- 6.6 Real-Time Printing
- 6.7 Alarm Reset
Chapter 7 Viewing Single Bed
- 7.1 Display of Single Bed
- 7.2 Hiding/Showing Multi-Lead Waveform
- 7.3 Short Trend Review
- 7.4 OxyCRG
- 7.5 Freeze
Chapter 8 Setting Telemetry Transmitters via MFM-CMS
- 8.1 Changing Patient Information
- 8.2 Setting Parameters
  - 8.2.1 Parameters Alarm Setting
  - 8.2.2 Physiological Parameter Attribute and Configuration
Chapter 9 Review
- 9.1 Patient List
- 9.2 Wave Review
- 9.3 Alarm Review
- 9.4 Trend Review
Chapter 10 System Setup
- 10.1 Common Setup
- 10.2 User Maintain
Chapter 11 Alarm Management
- 11.1 Overview
- 11.2 Alarm Levels
- 11.3 Parameters Alarm Setting
- 11.4 Alarm Mute
- 11.5 Audio Pause
- 11.6 Alarm Prompt/Response
- 11.7 Testing Alarms
- 11.8 Alarms for Networking Status
Chapter 12 Alarm Information
- 12.1 Physiological Alarm Information
- 12.2 Technical Alarm Information
- 12.3 Prompts
- 12.4 Adjustable Range of Alarm Limits
Chapter 13 Printing
- 13.1 Printing Report with a Printer
- 13.2 Printing Preview/ Printing Settings
  - 13.2.1 Printing Preview
  - 13.2.2 Printing Settings
- 13.3 Exporting the PDF File
Chapter 14 Database Management
- 14.1 Database Backup
- 14.2 Reviewing Backup Database
Chapter 15 Monitoring ECG
- 15.1 Overview
- 15.2 ECG Safety Information
- 15.3 ECG Display
  - 15.3.1 ECG Display on Telemetry Transmitter Screen
  - 15.3.2 ECG Display on MFM-CMS
- 15.4 Selecting Calculation Lead
- 15.5 Changing Size of ECG Waveform
- 15.6 Changing ECG Filter Settings
- 15.7 ECG Alarm Settings
- 15.8 Monitoring Procedure
  - 15.8.1 Preparation
  - 15.8.2 Connecting ECG Cables
- 15.9 Installing Electrodes
  - 15.9.1 Electrode Placement for 3-lead
  - 15.9.2 Electrode Placement for 5-lead
- 15.10 Setting Alarm Source
- 15.11 Smart Lead Off
- 15.12 Setting Pace Status
- 15.13 ECG Calibration
- 15.14 ECG Waveform Settings
- 15.15 ST Segment Monitoring
- 15.16 Arr. Monitoring
  - 15.16.1 Arrhythmia Analysis
  - 15.16.2 ARR Analysis Menu
Chapter 16 Monitoring RESP
- 16.1 Overview
- 16.2 RESP Safety Information
- 16.3 Electrode Placement for Monitoring RESP
- 16.4 Cardiac Overlay
- 16.5 Chest Expansion
- 16.6 Abdominal Breathing
- 16.7 Selecting RESP Lead
- 16.8 Changing the Apnea Time
- 16.9 Changing the Size and Speed of the Respiration Waveform
- 16.10 RESP Alarm Settings
Chapter 17 Monitoring SpO2
- 17.1 Overview
- 17.2 SpO2 Safety Information
- 17.3 Measuring SpO2
- 17.4 Measurement Procedure
- 17.5 Assessing the Validity of a SpO2 Reading
- 17.6 SpO2 Alarm Delay
- 17.7 Setting Sensitivity
- 17.8 SpO2 Alarm Settings
Chapter 18 Monitoring PR
- 18.1 Overview
- 18.2 Selecting the Active Alarm Source
- 18.3 PR Alarm Settings
Chapter 19 Using Battery
- 19.1 Battery Status on Screen
- 19.2 Replacing the Battery
- 19.3 Recycling the Battery
Chapter 20 Safety
- 20.1 Control and Safety Index
- 20.2 Characteristics
Chapter 21 Care and Cleaning
- 21.1 General Points
- 21.2 Cleaning
  - 21.2.1 Cleaning the Telemetry Transmitter
  - 21.2.2 Cleaning the Reusable Accessories
- 21.3 Disinfection
  - 21.3.1 Disinfecting the Telemetry Transmitter
  - 21.3.2 Disinfecting the Reusable Accessories
Chapter 22 Maintenance
- 22.1 Inspecting
- 22.2 Maintenance Task and Test Schedule
Chapter 23 Warranty and Service
- 23.1 Warranty
- 23.2 Contact information
Chapter 24 Accessories
- 24.1 ECG Accessories
- 24.2 SpO2 Accessories
- 24.3 Other Accessories
A Product Specifications
- A.1 Classification of Telemetry Transmitter
- A.2 Specifications of Telemetry Transmitter
- A.3 Data Storage
- A.4 Specifications of MFM-CMS
  - A.4.1 Recommended Hardware Configuration
  - A.4.2 Software Performance
- A.5 ECG
- A.6 RESP
- A.7 SpO2
- A.8 Wi-Fi
B EMC Information
- B.1 Electromagnetic Emissions
- B.2 Electromagnetic Immunity
- B.3 Electromagnetic Immunity
- B.4 Recommended Separation Distances
C Default Settings
- C.1 Patient Information Default Settings
- C.2 Alarm Default Settings (MFM-CMS)
- C.3 ECG Default Settings
- C.4 RESP Default Settings
- C.5 SpO2 Default Settings
- C.6 PR Default Settings
D Abbreviation

Telemetry Transmitter User Manual Installation of telemetry monitoring system

3.4 Wireless Network

Telemetry translator and MFM-CMS construct wireless network through AP. The qualified

engineers specified by EDAN are responsible for installing wireless network and performance

tests. For details, please refer to Patient Monitor Wireless Network Installation Guide.

NOTE:

1. Be aware that some network-based functions may be limited for telemetry transmitter

on wireless networks in comparison with those on wired networks.

2. The obstacle may interfere with data transmission and even cause data loss.

3. When telemetry transmitter has been connected to a wireless network, to make the

change of the Bed No. effective, you need to disconnect the wireless connection and

then connect it again or reboot telemetry transmitter.

3.5 Installation Method

The personnel specified by EDAN are responsible for system installation, which includes

surrounding verification, MFM-CMS installation, wireless device installation and telemetry

transmitter installation, etc.

WARNING

1. When the system is required to connected with other electric devices, and those

electric devices are not approved to be safe for connection with the system, such as

current leakage may cause electronic shock, please contact specialists in hospital or

our service personnel.

2. Upgrade operation is only for personnel authorized by EDAN.

3. Plugging three-pin into two-pin adaptor is prohibited.

4. To change installation environment or move system to another site, please contact

our service personnel.

5. The medical electrical equipment needs to be installed and put into service according

to the EMC Information provided in this user manual.

CAUTION

1. To avoid unpredictable results from sudden power interruption, please provide UPS

(Uninterruptible power supplies) for the system.

2. Keeping battery bin dry is required.

- 25 -