User's Manual

ManualsBrandsEDAN INSTRUMENTS ManualsElectronicsBlood Gas and Chemistry Analyzer

Table Of Contents

About this Manual
Statement
Responsibility of the Manufacturer
Terms Used in this Manual
Table of Contents
Chapter 1 Safety Guide
- 1.1 Intended Use
- 1.2 Warnings and Cautions
  - 1.2.1 Safety Warnings
  - 1.2.2 Safety Cautions
- 1.3 Symbols and Definitions
Chapter 2 System Overview
- 2.1 Introduction
- 2.2 System Frame
- 2.3 Analyzer Appearance
- 2.4 System Parts
- 2.5 Configuration
  - 2.5.1 Standard Configuration
  - 2.5.2 Options
Chapter 3 Installation Guide
- 3.1 Unpacking Inspection
- 3.2 Installation Requirements
  - 3.2.1 Environmental Requirements
  - 3.2.2 Power Requirements
- 3.3 Setting Up
Chapter 4 Setup
- 4.1 Getting into the Setup Screen
- 4.2 System Setup
- 4.3 Test Setup
Chapter 5 Patient Analyzing
- 5.1 Sample Collection and Preparation
- 5.2 Patient Analyzing
  - 5.2.1 Procedures for Patient Analyzing
  - 5.2.2 Understanding Result Symbols
- 5.3 Patient Sample Database
Chapter 6 Quality Control (QC) Tests
- 6.1 Control Test
- 6.2 Proficiency Test
  - 6.2.1 Procedures for Proficiency Test
  - 6.2.2 Proficiency Database
- 6.3 Simulator Test
  - 6.3.1 Procedures for External Simulator Test
  - 6.3.2 Simulator Database
    - 6.3.2.1 Searching for Simulator Test Data
    - 6.3.2.2 Exporting/Uploading/Printing Simulator Test Data
Chapter 7 Data Management
- 7.1 Introduction
- 7.2 Databases
Chapter 8 Online Update
- 8.1 Introduction
- 8.2 Procedures for Online Update
Chapter 9 Troubleshooting
Chapter 10 Cleaning, Care and Maintenance
- 10.1 Cleaning and Disinfecting the Analyzer
- 10.2 Care and Maintenance
Chapter 11 Theory
- 11.1 Measurement Method
- 11.2 Determination of Test Results
  - 11.2.1 Determination of the Analyte Concentration
  - 11.2.2 Determination of Cell Concentration
- 11.3 Equations for Calculated Parameters
Chapter 12 Parameters
- 12.1 pH
- 12.2 pCO2
- 12.3 pO2
- 12.4 Sodium (Na+)
- 12.5 Potassium (K+)
- 12.6 Ionized Calcium (Ca++)
- 12.7 Chloride (Cl-)
- 12.8 Hematocrit (Hct)
Chapter 13 Warranty and Service
- 13.1 Warranty
- 13.2 Contact Information
Appendix 1 Specifications
- A1.1 Environment Requirements
- A1.2 Analyzer Specifications
- A1.3 Performance Specifications
- A1.4 Printer
- A1.5 Rechargeable Battery
- A1.6 Safety Specifications
Appendix 2 Measurement Ranges
- A2.1 Measurement Ranges for Measured Parameters
- A2.2 Measurement Ranges for Calculated Parameters
Appendix 3 Reference Ranges
Appendix 4 EMC Information
Appendix 5 FCC Information
- A5.1 FCC Statement
- A5.2 FCC RF Radiation Exposure Statement
Appendix 6 Order List

i15 Blood Gas and Chemistry Analysis System User Manual Quality Control (QC) Tests

- 74 -

9. Press Scan Barcode, and scan the bar code on the controls user manual.

If the bar code is scanned successfully, the system will beep and the scanner will be

automatically turned off. If the scanned data is valid, the system will display the screen for

the next procedure. If the scanned data is invalid, a message will pop up to prompt you.

Figure 6-4 Scan Bar Code

NOTE:

Keep the controls user manual for a future control test use.

10. Mix the controls completely by shaking the ampoule gently, and then tap the tip of the

ampoule carefully with your fingernail to remove any solution.

Figure 6-5 Mix Controls and Insert Cartridge

NOTE:

Avoid heating the ampoule with your hands when shaking the ampoule.