User's Manual

ManualsBrandsEDAN INSTRUMENTS ManualsElectronicsBlood Gas and Chemistry Analyzer

111

112

113

114

115

116

117

118

119

120

Table Of Contents

About this Manual
Statement
Responsibility of the Manufacturer
Terms Used in this Manual
Table of Contents
Chapter 1 Safety Guide
- 1.1 Intended Use
- 1.2 Warnings and Cautions
  - 1.2.1 Safety Warnings
  - 1.2.2 Safety Cautions
- 1.3 Symbols and Definitions
Chapter 2 System Overview
- 2.1 Introduction
- 2.2 System Frame
- 2.3 Analyzer Appearance
- 2.4 System Parts
- 2.5 Configuration
  - 2.5.1 Standard Configuration
  - 2.5.2 Options
Chapter 3 Installation Guide
- 3.1 Unpacking Inspection
- 3.2 Installation Requirements
  - 3.2.1 Environmental Requirements
  - 3.2.2 Power Requirements
- 3.3 Setting Up
Chapter 4 Setup
- 4.1 Getting into the Setup Screen
- 4.2 System Setup
- 4.3 Test Setup
Chapter 5 Patient Analyzing
- 5.1 Sample Collection and Preparation
- 5.2 Patient Analyzing
  - 5.2.1 Procedures for Patient Analyzing
  - 5.2.2 Understanding Result Symbols
- 5.3 Patient Sample Database
Chapter 6 Quality Control (QC) Tests
- 6.1 Control Test
- 6.2 Proficiency Test
  - 6.2.1 Procedures for Proficiency Test
  - 6.2.2 Proficiency Database
- 6.3 Simulator Test
  - 6.3.1 Procedures for External Simulator Test
  - 6.3.2 Simulator Database
    - 6.3.2.1 Searching for Simulator Test Data
    - 6.3.2.2 Exporting/Uploading/Printing Simulator Test Data
Chapter 7 Data Management
- 7.1 Introduction
- 7.2 Databases
Chapter 8 Online Update
- 8.1 Introduction
- 8.2 Procedures for Online Update
Chapter 9 Troubleshooting
Chapter 10 Cleaning, Care and Maintenance
- 10.1 Cleaning and Disinfecting the Analyzer
- 10.2 Care and Maintenance
Chapter 11 Theory
- 11.1 Measurement Method
- 11.2 Determination of Test Results
  - 11.2.1 Determination of the Analyte Concentration
  - 11.2.2 Determination of Cell Concentration
- 11.3 Equations for Calculated Parameters
Chapter 12 Parameters
- 12.1 pH
- 12.2 pCO2
- 12.3 pO2
- 12.4 Sodium (Na+)
- 12.5 Potassium (K+)
- 12.6 Ionized Calcium (Ca++)
- 12.7 Chloride (Cl-)
- 12.8 Hematocrit (Hct)
Chapter 13 Warranty and Service
- 13.1 Warranty
- 13.2 Contact Information
Appendix 1 Specifications
- A1.1 Environment Requirements
- A1.2 Analyzer Specifications
- A1.3 Performance Specifications
- A1.4 Printer
- A1.5 Rechargeable Battery
- A1.6 Safety Specifications
Appendix 2 Measurement Ranges
- A2.1 Measurement Ranges for Measured Parameters
- A2.2 Measurement Ranges for Calculated Parameters
Appendix 3 Reference Ranges
Appendix 4 EMC Information
Appendix 5 FCC Information
- A5.1 FCC Statement
- A5.2 FCC RF Radiation Exposure Statement
Appendix 6 Order List

i15 Blood Gas and Chemistry Analysis System User Manual Troubleshooting

- 109 -

Well” appears.

please contact EDAN or its authorized

distributors for assistance.

8 The prompt “Cartridge Expired” appears.

Verify that the current date is correct. If the

prompt appears again, check that the test

cartridge has not expired. If it has expired,

use a new test cartridge that has not expired.

The prompt “

Calibrant is Not Aspirated

Properly” appears.

erform the test again with a new test

cartridge. I

f the prompt appears again,

please contact EDAN or its authorized

distributors for assistance.

The prompt “Air is Not Aspirated Properly”

appears.

erform the test again with a new test

cartridge. I

f the prompt appears again,

please contact EDAN or its authorized

distributors for assistance.

The prompt “Sample Error. Maybe Clots are

Detected in Sample” appears.

Check that there are no clots in the blood

sample. If there are clots, discard it and

collect samples again.

12 The prompt “Insertion Error” appears.

erify that a simulator is inserted during a

simulator test and a test cartridge is inserted

during a sample test.

The prompt “

Calibrant Pack Expired,

Confirm Date Setup and Calibrant Pack’s

Expiration Date” appears.

Verify that the current date is correct. If the

prompt appears again, check that the

calibrant fluid pack has not expired. If it has

expired, replace the calibrant fluid pack

following the user manual instructions.

14 The prompt “Remaining Days: 0” appears.

he calibrant fluid pack has expired.

eplace the calibrant fluid pack following

the user manual instructions.

The prompt “Calibrant Pack Depleted”

appears.

The calibrant fluid pack has been depleted.

Replace the calibrant flu

id pack following

the user manual instructions.

16 The prompt “Current Date Error” appears.

The date is earlier than the manufacture date

of the calibrant fluid pack. Ensure that the

current date is correct.

The prompt “

Calibrant Pack Improper

Removal. Please Replace Calibrant Pack”

appears.

The calibrant fluid pack

is removed from

the system improperly. Replace the calibrant

fluid pack following the user manual

instructions.