User's Manual

ManualsBrandsEDAN INSTRUMENTS ManualsElectronicsBlood Gas and Chemistry Analyzer

101

102

103

104

105

106

107

108

109

110

Table Of Contents

About this Manual
Statement
Responsibility of the Manufacturer
Terms Used in this Manual
Table of Contents
Chapter 1 Safety Guide
- 1.1 Intended Use
- 1.2 Warnings and Cautions
  - 1.2.1 Safety Warnings
  - 1.2.2 Safety Cautions
- 1.3 Symbols and Definitions
Chapter 2 System Overview
- 2.1 Introduction
- 2.2 System Frame
- 2.3 Analyzer Appearance
- 2.4 System Parts
- 2.5 Configuration
  - 2.5.1 Standard Configuration
  - 2.5.2 Options
Chapter 3 Installation Guide
- 3.1 Unpacking Inspection
- 3.2 Installation Requirements
  - 3.2.1 Environmental Requirements
  - 3.2.2 Power Requirements
- 3.3 Setting Up
Chapter 4 Setup
- 4.1 Getting into the Setup Screen
- 4.2 System Setup
- 4.3 Test Setup
Chapter 5 Patient Analyzing
- 5.1 Sample Collection and Preparation
- 5.2 Patient Analyzing
  - 5.2.1 Procedures for Patient Analyzing
  - 5.2.2 Understanding Result Symbols
- 5.3 Patient Sample Database
Chapter 6 Quality Control (QC) Tests
- 6.1 Control Test
- 6.2 Proficiency Test
  - 6.2.1 Procedures for Proficiency Test
  - 6.2.2 Proficiency Database
- 6.3 Simulator Test
  - 6.3.1 Procedures for External Simulator Test
  - 6.3.2 Simulator Database
    - 6.3.2.1 Searching for Simulator Test Data
    - 6.3.2.2 Exporting/Uploading/Printing Simulator Test Data
Chapter 7 Data Management
- 7.1 Introduction
- 7.2 Databases
Chapter 8 Online Update
- 8.1 Introduction
- 8.2 Procedures for Online Update
Chapter 9 Troubleshooting
Chapter 10 Cleaning, Care and Maintenance
- 10.1 Cleaning and Disinfecting the Analyzer
- 10.2 Care and Maintenance
Chapter 11 Theory
- 11.1 Measurement Method
- 11.2 Determination of Test Results
  - 11.2.1 Determination of the Analyte Concentration
  - 11.2.2 Determination of Cell Concentration
- 11.3 Equations for Calculated Parameters
Chapter 12 Parameters
- 12.1 pH
- 12.2 pCO2
- 12.3 pO2
- 12.4 Sodium (Na+)
- 12.5 Potassium (K+)
- 12.6 Ionized Calcium (Ca++)
- 12.7 Chloride (Cl-)
- 12.8 Hematocrit (Hct)
Chapter 13 Warranty and Service
- 13.1 Warranty
- 13.2 Contact Information
Appendix 1 Specifications
- A1.1 Environment Requirements
- A1.2 Analyzer Specifications
- A1.3 Performance Specifications
- A1.4 Printer
- A1.5 Rechargeable Battery
- A1.6 Safety Specifications
Appendix 2 Measurement Ranges
- A2.1 Measurement Ranges for Measured Parameters
- A2.2 Measurement Ranges for Calculated Parameters
Appendix 3 Reference Ranges
Appendix 4 EMC Information
Appendix 5 FCC Information
- A5.1 FCC Statement
- A5.2 FCC RF Radiation Exposure Statement
Appendix 6 Order List

i15 Blood Gas and Chemistry Analysis System User Manual Quality Control (QC) Tests

- 93 -

3. On the Main screen, press to go to the Quality Control screen, and then press .

4. Gently insert the external electronic simulator into the cartridge port, and press down to

ensure it clicks into place. If the electronic simulator is inserted properly, the system will

automatically perform a simulator test.

Figure 6-29 Insert External Simulator

NOTE:

 Avoid touching the contact pads.

 Never touch the simulator after inserting it into the system.

5. The system automatically starts to perform an external simulator test.

Figure 6-30 Measurement in Progress