User's Manual

ManualsBrandsEDAN INSTRUMENTS ManualsElectronicsBlood Gas and Chemistry Analyzer

100

Table Of Contents

About this Manual
Statement
Responsibility of the Manufacturer
Terms Used in this Manual
Table of Contents
Chapter 1 Safety Guide
- 1.1 Intended Use
- 1.2 Warnings and Cautions
  - 1.2.1 Safety Warnings
  - 1.2.2 Safety Cautions
- 1.3 Symbols and Definitions
Chapter 2 System Overview
- 2.1 Introduction
- 2.2 System Frame
- 2.3 Analyzer Appearance
- 2.4 System Parts
- 2.5 Configuration
  - 2.5.1 Standard Configuration
  - 2.5.2 Options
Chapter 3 Installation Guide
- 3.1 Unpacking Inspection
- 3.2 Installation Requirements
  - 3.2.1 Environmental Requirements
  - 3.2.2 Power Requirements
- 3.3 Setting Up
Chapter 4 Setup
- 4.1 Getting into the Setup Screen
- 4.2 System Setup
- 4.3 Test Setup
Chapter 5 Patient Analyzing
- 5.1 Sample Collection and Preparation
- 5.2 Patient Analyzing
  - 5.2.1 Procedures for Patient Analyzing
  - 5.2.2 Understanding Result Symbols
- 5.3 Patient Sample Database
Chapter 6 Quality Control (QC) Tests
- 6.1 Control Test
- 6.2 Proficiency Test
  - 6.2.1 Procedures for Proficiency Test
  - 6.2.2 Proficiency Database
- 6.3 Simulator Test
  - 6.3.1 Procedures for External Simulator Test
  - 6.3.2 Simulator Database
    - 6.3.2.1 Searching for Simulator Test Data
    - 6.3.2.2 Exporting/Uploading/Printing Simulator Test Data
Chapter 7 Data Management
- 7.1 Introduction
- 7.2 Databases
Chapter 8 Online Update
- 8.1 Introduction
- 8.2 Procedures for Online Update
Chapter 9 Troubleshooting
Chapter 10 Cleaning, Care and Maintenance
- 10.1 Cleaning and Disinfecting the Analyzer
- 10.2 Care and Maintenance
Chapter 11 Theory
- 11.1 Measurement Method
- 11.2 Determination of Test Results
  - 11.2.1 Determination of the Analyte Concentration
  - 11.2.2 Determination of Cell Concentration
- 11.3 Equations for Calculated Parameters
Chapter 12 Parameters
- 12.1 pH
- 12.2 pCO2
- 12.3 pO2
- 12.4 Sodium (Na+)
- 12.5 Potassium (K+)
- 12.6 Ionized Calcium (Ca++)
- 12.7 Chloride (Cl-)
- 12.8 Hematocrit (Hct)
Chapter 13 Warranty and Service
- 13.1 Warranty
- 13.2 Contact Information
Appendix 1 Specifications
- A1.1 Environment Requirements
- A1.2 Analyzer Specifications
- A1.3 Performance Specifications
- A1.4 Printer
- A1.5 Rechargeable Battery
- A1.6 Safety Specifications
Appendix 2 Measurement Ranges
- A2.1 Measurement Ranges for Measured Parameters
- A2.2 Measurement Ranges for Calculated Parameters
Appendix 3 Reference Ranges
Appendix 4 EMC Information
Appendix 5 FCC Information
- A5.1 FCC Statement
- A5.2 FCC RF Radiation Exposure Statement
Appendix 6 Order List

i15 Blood Gas and Chemistry Analysis System User Manual Quality Control (QC) Tests

- 92 -

6.2.2.3 Exporting/Uploading/Printing Proficiency Test Data

1. Open the proficiency database.

2. Select the desired proficiency test data.

To Do this

Export

Insert a removable disk into the analyzer, and then press Export.

Upload

Press Upload.

Press Print.

NOTE:

If no proficiency test data is selected before pressing Export/Upload/Print, all of the data

stored in the proficiency database will be exported/uploaded/printed.

6.3 Simulator Test

6.3.1 Procedures for External Simulator Test

Follow the procedures below to perform an external simulator test:

1. Press the On/Off button on the left hand side of the analyzer to turn it on.

2. Enter the user name and password manually, and then press .

To scan the bar code of the user name, press first, and then scan the bar code.

Figure 6-28 Enter User Name and Password