BATTERY STATUS INDICATOR LEDs indicate battery and charging status as following table. Adapter Mode Battery Mode Geen(100%) Solid Solid Green (80% ~) Flash Solid Orange(15%~79%) Flash Solid Red(~14%) Flash Solid TM In battery mode, MosicGO will be forced to power off if battery capacity is under 10%. Suggest charging the battery immediately. *Note: There is no battery in Lite MGFU-L verion. Power LED is green solid when DC adapter is inserted.
CONNECT INPUT SOURCE HDMI BY HDMI SPLITTER (6-A) TO USB PORT SOURCES MosicGO TM POWER INPUT DC5V OUTPOT 1 OUTPOT 2 Page5 6-A HDMI SPLITTER MosicGO TM TO HDMI *Note: Please always use the splitter to connect to any source (Laptop, PC, DVD…) and the projector. Electronic file link www.eliteprojector.com/MGFU/manual 8 FBZZ-MG1Z002-01 www.eliteprojector.
CONNECT INPUT SOURCE : USB Type C Display Port ADJUST PROJECTION IMAGE TILT The projector is equipped with four elevator feet for adjusting the projected image tilt. Adjust the focus until the image is clear. To adjust the tilt: Turn the elevator feet to adjust the projected image position to the desired tilt. Electronic file link www.eliteprojector.com/MGFU/manual 9 FBZZ-MG1Z002-01 www.eliteprojector.
ADJUST THE PROJECTION IMAGE SIZE A B Projector Front Screen lower Edge Distance to edge Screen to projector table C D E Projector Screen Projector Screen Projector Screen diagonal width height inch inch inch inch inch 3.82 9.41 60 52.3 29.4 6.42 10.75 70 61.0 34.3 9.17 11.89 80 69.7 39.2 11.97 13.35 90 78.4 44.1 14.53 14.37 100 87.2 49.
EARPHONE 12V TRIGGER GND HPR GND HPL 12V Earphone, 3.5mm Jack Pin assignment 12V Trigger Port, 3.5mm Jack Pin assignment HPL : Left Channel Audio Signal HPR : Right Channel Audio Signal GND : Signal Ground 12V : 12V trigger signal for screen rolling up/down GND : Signal Ground To Earphone Plug To 12V Trigger Plug Warning : Don’t plug in earphone to 12V trigger port, that can cause damage to the earphone. Electronic file link www.eliteprojector.com/MGFU/manual 11 FBZZ-MG1Z002-01 www.
MOUNT CO THE PROJECTOR Mount on tripod Mount on ceiling M4 Screw (x4) Screw hole for tripod *Standard Tripod Screw a standard tripod into the screw hole on the projector. 1. Loosen 4 screws 2. Fasten screws *Note: Tripod should support loading above 3Kg, and mounting screw spec is 1/4” On table metal plate from MosicGO . to ceiling mount kits. TM Note1 Keep enough space from speakers and ventilations (30 cm above) Note2 4 rubber feet are placed on flat surface.
OSD MosicGO TM RGB Contrast: adjust color contrast. Sharpness: adjust picture sharpness. Pattern Test: present pattern picture to verify focus and color situation of display. Press “OK” will return to current video port. PICTURE Contrast Sharpness Pattern Test *Note: 1.Reset to default setting by selecting 'Menu'->'Other'->'Reset' MENU OK MosicGO TM RGB DISPLAY Auto PowerOff ［ H Position Off ［ Auto PowerOff: Configure the time before power off if there is no signal to projector.
OSD MosicGO TM RGB Configure color properties. COLOR Gamma ［ Off ［ Color Temp ［ Off ［ Color Effect ［ Standard ［ ［ RGB ［ Color Format *Note: 1.Some features might not be support in current model. 2.Reset to default setting by selecting 'Menu'->'Other'->'Reset' HUE Saturation MENU OK MosicGO TM RGB ADVANCE Aspect Ratio ［ Full ［ Orientation ［ FrontTable ［ Ultra Viivid ［ Off ［ Set other configuration. Aspect Ratio: configure ratio of display area.
OSD MosicGO TM RGB 12V Trigger: Enable/disable the output of 12VTrigger Out. Keystone: adjust the rectangle shape of display. Transparency: configure the transparency of OSD(on-screen display). S.P.M: enable/disable Smart Projector Mode. If enable, MosicGO will automatically adjust brightness according current battery and power situation. Rest: reset to default setting. OTHER 12V Trigger ［ Off ［ Keystone ［ On ［ S.P.
SPECIFICATIONS Item Imager Native Resolution Projection Distance Projection Size Focus Throw Ratio TROUBLESHOOTING Description DLP 1 0. If you experience a problem with your projector, please refer to the following information. If a problem persists, please contact your local retailer or service center. x 1080 -0. No image appears on screen m (1' " - 2'2") (from screen to lens) 1.52-2.54 m ( Ensure the cable is fine.
TROUBLESHOOTING 3 continuous beep sound You may hear 3 continuous beep sound accompany following icon on the screen Low battery: projector is turned off immediately. Please plug power adapter to charge the battery. You can turn on the projector during charging. Battery fail: if the power adapter is plugged. You can turn on and use projector. If you pull out the power adapter, the projector may be turned off without any warning. If the problem still occurs, please check your vendor.
13 Months Warranty Card Customer’s name: Phone number: Email: Address: Date of purchase: (M) (D) (Y) Model No: S/N: ＊To ensure your right, please ask the Dealer to fill in the information above, and have Dealer’s stamp on this card. Dealer’s Stamp: ＊If date of purchase cannot be provided with dealer’s stamp, the manufacture date as recorded will be deemed to be the start of the Warranty Period. MosicGO TM MOVIES MUSIC POWER GO Elite Screens Visual & Sound Co., Ltd. Electronic file link www.
TM MOVIES MUSIC POWER GO Electronic file link www.eliteprojector.com/MGFU/manual FBZZ-MG1Z002-01 www.eliteprojector.
