:10-SCALE 2WD MONSTER TRUCK KIT ECX03034 // ECX03034l INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D’UTILISATION MANUALE DI ISTRUZIONI Congratulations on your purchase of the ECX® AMP® MT 2WD Monster Truck kit. This 1:10-scale model introduces you to the sport of RC driving. Herzlichen Glückwunsch zum Kauf des ECX AMP MT 2WD Monster Truck. Dieses 1:10 Scale Model öffnet Ihnen die Welt des RC Car Sports. Nous vous félicitons pour l’achat du ECX AMP MT 2WD Monster Truck.
EN NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit http://www.horizonhobby.com and click on the support tab for this product.
EN WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS Your new Horizon Hobby vehicle has been designed and built with a combination of waterproof and water-resistant components to allow you to operate the product in many “wet conditions,” including puddles, creeks, wet grass, snow and even rain. While the entire vehicle is highly water-resistant, it is not completely waterproof and your vehicle should NOT be treated like a submarine.
EN GETTING STARTED 1 2 3 4 5 6 Charge the battery Assemble the AMP Monster Truck Paint the AMP Monster Truck Install the battery Setup the transmitter Drive! 4 2 1 5 3 CHARGING WARNINGS WARNING: Failure to exercise caution while using this product and comply with the following warnings could result in product malfunction, electrical issues, excessive heat, FIRE, and ultimately injury and property damage. • NEVER LEAVE CHARGING BATTERIES UNATTENDED. • NEVER CHARGE BATTERIES OVERNIGHT.
EN STEP 2: ASSEMBLE THE AMP MONSTER TRUCK Thank you for purchasing the AMP Monster Truck Kit. The kit includes 6 bags marked A–F. Each bag contains secondary bags labelled with assembly step numbers. The kit contains the correct a1 x1 number of parts to build the AMP Monster Truck. Open the "Tools" bag first. Then open the part bags, one at a time.
EN a2 x1 x1 x2 3 M3 x 10mm 1 4 2 M3 x 10mm 6
EN a3 x1 x4 1 2 M3 x 12mm 7
EN a4 x1 x1 x4 1 2 3 M3 x 18mm 8
EN a5 x2 x1 1 2 9
EN a6 x1 x1 x1 x1 X1 4 3 2 1 10
EN a7 x1 x2 11
EN a8 x1 1 2 12
EN a9 x1 x1 3 2 1 13
EN a10 x1 x1 x1 x1 x1 3 M3 x 12mm M3.
EN a11 x4 x2 M3 x 10mm 2 3 M3 x 25mm M3 x 10mm 4 1 M3 x 10mm 15
EN b1 x1 x1 x2 3 4 2 16 1
EN b2 x2 x1 2 1 M2 x 8mm 17
EN b3 x1 x1 x2 M3 x 12mm 1 18 2
EN b4 x4 1 2 M3 x 12mm 19
EN b5 x2 x2 x2 4 5 6 2 1 3 M2.5 x 4mm M2.
EN b6 x4 x2 x2 21
EN b7 x4 1 2 4 3 M3 x 15mm M3 x 15mm 22
EN b8 x4 x2 x1 x1 6 3 1 5 4 2 23
EN b9 x2 x2 x2 1 3 5 2 6 4 24
EN b10 x4 5 4 2 6 3 1 25
EN b11 26 x2
EN b12 x1 x2 2 M3 x 18mm 1 27
EN c1 x1 x1 1 2 M3 x 18mm 28 x2
EN c2 x1 x1 x2 x2 1 2 4 3 5 6 M2.
EN c3 x4 M3 x 12mm 2 1 30
EN c4 x1 x4 M3 x 18mm 2 1 31
EN c5 x1 x4 M3 x 15mm 2 1 32
EN c6 x2 x4 1 4 2 3 33
EN c7 x2 x2 x2 3 2 1 4 5 34 6
EN c8 x2 x2 1 2 4 3 5 M2.
EN c9 x2 x4 x2 36
EN c10 x2 3 1 4 2 M3 x 15mm 37
EN c11 x2 M3 x 12mm M3 x 12mm 38
EN d1 x2 x1 1 x1 2 39
EN d2 x2 x1 x1 1 2 3 40
EN d3 x1 x1 x1 2 1 41
EN d4 x1 3 2 1 42
EN d5 43
EN d6 x3 x1 M3 x 18mm M3 x 12mm 44
EN d7 x1 x1 x1 2 1 3 45
EN d8 x1 x1 x2 x1 1 5 2 3 46 4
EN d9 2.
EN d10 x1 x2 x2 x2 M3 x 8mm M3 x 8mm 48
EN d11 x2 x1 x1 1 2 3 M3 x 8mm 49
EN d12 x3 M2.5 x 8mm 1 2 M2.
EN d13 x2 x2 3 1 4 2 51
EN d14 x1 x2 M3 x 12mm 2 1 52
EN d15 2 1 53
EN d16 x2 M3 x 12mm 54
EN d17 x2 M3 x 12mm 55
EN d18 x1 x2 x2 M3 x 10mm 3 1 2 M3 x 12mm 56
EN e1 x2 x2 x2 x2 M3 x 25mm M3 x 12mm 5 1 6 7 8 2 4 3 M3 x 5.
EN e2 x2 x2 x2 x2 3 2 M3 x 5.
EN f1 x1 x2 1 2 59
EN f2 x2 x1 1 2 M3 x 12mm 60
EN f3 x2 x2 2 1 M3 x 15mm 61
EN f4 x1 x1 2 1 62
EN f5 x1 x1 x1 2 1 63
EN f6 + − + − + − 64 + −
EN f7 x1 65
EN f8 66 x2
EN f9 x4 x4 5 6 8 7 4 3 1 2 67
EN f10 68 x2
EN f11 x4 1 2 69
EN STEP 3: PAINT AND STICKER THE AMP MONSTER TRUCK BODY SHELL 1. Clean the inside of the AMP MT body shell using a small amount of water and dish soap. Thoroughly rinse and dry the body shell with a cloth towel. Tip: Do not use paper towels. 2. Paint the inside of the AMP MT body shell. 3. Once the paint is completely dry, remove the over-spray film from the outside of the body. 4. Using the chart below, apply the windows, grill, head lights, and tail lights.
EN STEP 5: SET UP THE RADIO SYSTEM 1. 2. 3. 4. Remove the battery cover from the transmitter. Install four AA batteries as shown. Re-install the battery cover. Review the transmitter controls (below). The Transmitter and ESC are bound at the factory. If you need to rebind, follow the BINDING instructions. BINDING 1. Power OFF the ESC/Receiver and transmitter. 2. Connect a fully charged battery to the ESC/Receiver. 3. Turn on the ESC/Receiver and confirm the LED is flashing slowly. 4.
EN STEP 6: DRIVE 1 Power on the transmitter. 2 3 Power on the ESC. Drive! WHEN YOU ARE FINISHED 1 Power off the ESC. 2 Power off the transmitter. 3 Remove and recharge the battery pack. ELECTRONIC SPEED CONTROL (ESC) Connecting Calibrating 1. Connect the RED (+) ESC wire to the RED (+) motor wire. 2. Connect the BLACK (–) ESC wire to the BLACK (–) motor wire. Ensure proper ESC function by calibrating the ESC to your transmitter inputs.
EN TROUBLESHOOTING GUIDE Problem Short Run Time Sluggish Action Controls Reversed Motor/ESC overheat Does Not Operate Poor Range The system will not connect • • • • • • • • • • • • • • • • • • The receiver goes into failsafe mode a short distance away from the transmitter The receiver quits responding during operation Receiver and transmitter are not bound Vehicle moves forward or backward without input from user Car does not drive straight No steering or lack of steering No throttle or lack of throttl
EN LIMITED WARRANTY What This Warranty Covers Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase.
EN WARRANTY AND SERVICE CONTACT INFORMATION Country of Purchase United States of America Horizon Hobby Contact Information Horizon Service Center (Repairs and Repair Requests) servicecenter.horizonhobby.com/RequestForm/ Horizon Product Support (Product Technical Assistance) productsupport@horizonhobby.com 877-504-0233 Sales websales@horizonhobby.com 800-338-4639 Horizon Technischer Service service@horizonhobby.
IT Optional Parts List • Optionale Teile • Liste des options • Elenco parti opzionali Part Number English Deutsch Français Italiano DYN1060EC Speedpack 2400mAh Ni-MH 6-Cell Flat with EC3 Conn Speedpack 6-Zellen 2400mAh FlatNiMH-Akku m. EC3-Anschluss Speedpack Ni-Mh 7,2V 2400mA avec prise EC3 Speedpack 2400mAh batteria NiMH 6 celle flat con connettore EC3 DYN1070EC Speedpack 3300mAh Ni-MH 6-Cell Flat with EC3 Conn Speedpack 6-Zellen 3300mAh FlatNiMH-Akku m.
IT Replacement Parts List • Teileliste Part Number English Deutsch DYN1050EC Speedpack 1800mAh Ni-MH 6-Cell Flat with EC3 Connector Dynamite Speedpack 6-Zellen 1800mAh Flat-NiMH-Akku m.
IT Liste des pièces de rechange • Elenco dei ricambi Part Number Français Italiano DYN1050EC Speedpack Ni-Mh 7,2V 1800mA avec prise EC3 Speedpack 1800mAh NiMH 6 celle flat con connettore EC3 DYN1171 Moteur Brushed Dynamite 20T Dynamite 20-Turn motore brushed ECX1015 Roulements 5 x 10 x 4mm (10) 5 x 10 x 4mm cuscinetto (8) ECX1017 1/10 2WD Circuit - Châssis Telaio: 1:10 2WD Circuit ECX1018 1:10 2WD Cir/Ruc/Tor - Set de triangles avant Braccetti sospensioni ant.
IT PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÈCES | ESPLOSO DEL MODELLO CON REFERENZA PEZZI ECX1088 ECX1017 ECX1061 M3 x 15mm BH ECX1025 ECX1022 ECX1059 ECX1026 ECX1025 ECX1022 ECX1059 ECX1025 ECX1022 ECX1022 ECX1026 ECX1061 M2 x 16mm FH 104
ECX1037 ECX1036 ECX1039 ECX1037 ECX1043 ECX1037 ECX1038 ECX1041 ECX1038 ECX1037 ECX1043 ECX1057 ECX1060 ECX1092 ECX43012 ECX234000 ECX1046 ECX231000 ECX1061 M2 x 8mm ECX1061 M3 x 18mm FH ECX1092 ECX1061 M3 x 12mm BH ECX1018 ECX1044 ECX234000 ECX1065 ECX1015 ECX1092 ECX234000 ECX1065 ECX1061 M3 x 12mm BH ECX1061 M3 x 18mm BH ECX1058 ECX1049 ECX1050 ECX1058 ECX1046 ECX43012 ECX1060 ECX1061 M3 x 10mm BH ECX1061 M3 x 12mm FH ECX1092 ECX1061 M3 x 10mm BH ECX1028 ECX1058
ECX43012 106 ECX1092 ECX1060 ECX1015 ECX1049 ECX232000 ECX234000 ECX1061 M3 x 12mm BH ECX1046 ECX1019 ECX1061 M3 x 12mm FH ECX1044 ECX1061 M3 x 15mm BH ECX1044 ECX1033 ECX1061 M3 x 12mm FH ECX1045 ECX3010 ECX1059 ECX1061 M3 x 20mm BH ECX1061 M3 x 15mm BH ECX1061 M3 x 12mm BH ECX1044 ECX1092 ECX234000 ECX1092 ECX1015 ECX232000 ECX1046 ECX1061 M3 x 15mm BH ECX1044 ECX1045 ECX1033 ECX1021 ECX1061 M3 x 12mm BH ECX3015 ECX1048 ECX1019 ECX1061 M3 x 12mm BH ECX1088 ECX1061
ECX1060 ECX1024 ECX1076 ECX1061 M2.5 x 8mm BH ECX1061 M2.5 x 4mm BH ECX1061 M2.5 x 8mm BH ECX1024 ECX1015 ECX1061 M2.
ECX03034 www.ecxrc.com © 2018 Horizon Hobby, LLC. ECX, the ECX logo, AMP, EC3, Dynamite, Speedpack and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. Updated 04/2018 48613.
