/24 SCALE 4WD ELECTRIC FPV UTILITY VEHICLE INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D’UTILISATION MANUALE DI ISTRUZIONI ECX00018T1/ECX00018T2
NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit http://www.horizonhobby.com and click on the support tab for this product.
Box Contents • • • • • • EN ECX® Barrage® FPV Utility Vehicle 2-CH Transmitter (ECX10003) AA (4) Batteries USB 4.8V NiMH Charger (DYNC1060) NiMH, 220mAh, 4.8V (DYNB0007) Spektrum™ Video Monitor (SPMVM435) Specifications Frequency Battery Power supply Run Time Transmitter 2404 MHz – 2476 MHz AA x 4 Truck 4 cell 220mAh 4.8V NiMH 10 min Video Transmitter Input voltage 2.
Getting Started Charge the Vehicle Battery 1 Refer to charging warnings. 1. Connect the battery to the battery charger. 2. Connect the battery charger to a powered USB. 3. The battery will charge in under 2 hours. The LED sequence for the USB charger is Red = charging, Green = charge is complete. 2 Charge The Video Monitor 5V Micro USB Charge Port Fully charge the Video Monitor before use. 1. Connect the included micro USB charge cable to a 5V USB power source. 2.
Transmitter Controls 5 EN THROTTLE TRIGGER Reverse STEERING WHEEL Controls steering. Right and Left steering REVERSE SWITCH Forward Stop Controls power to the motor for forward or reverse BATTERY LEVEL INDICATOR Solid Red and Green: Battery voltage is good (above 4V). Allows you to change the direction ofsteering (ST. REV) and throttle (TH. REV)controls (Ensure proper function with a radio system test). Solid Red: Battery voltage is critically low (below 4V). Replace transmitter batteries.
Installing Your Transmitter Batteries 6 Power on the vehicle 8 CAUTION: NEVER remove the transmitter batteries while the model is powered on. Loss of model control, damage or injury may occur. CAUTION: If using rechargeable batteries, charge only rechargeable batteries. Charging nonrechargeable batteries may cause the batteries to burst, resulting in injury to persons and/or damage to property. CAUTION: Risk of explosion if battery is replaced by an incorrect type.
Wireless Video System 11 Select the video frequency EN NOTICE: If you are operating this product in North America, you are required to have an Amateur Radio (HAM) license. Visit www.arrl.org for more information. Video Transmitter (VTX) Button The video transmitter channel and band are changed using the button on the left side of the Shown with tire removed for clarity. camera module. Channel Selection: Band Selection: 1. Channel 1 is indicated by the red LED glowing 1.
13 Video Monitor controls 5.8GHz Antenna connector Menu Buttons: Use the + and – buttons to make changes: Frequency Band Button Single push to change band Channel Selection Button Single push to change channel Micro Memory Card Slot ON/Off Switch Charge Status LED Red = charging Green = charged VIDEO MONITOR MODES OF OPERATION AV In 5V Micro USB Charge Port When powered on, the video monitor is in FPV mode.
When You Are Finished Binding Troubleshooting 14 Power off the vehicle 15 Power off the transmitter and video monitor 16 Remove and recharge the vehicle battery EN Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identifier) code of a single specific transmitter. The included transmitter and receiver are bound at the factory. If you need to rebind, follow the instructions below. 1. Power off the transmitter and ESC. 2.
Troubleshooting Guide Problem Short run time Sluggish action Controls reversed Motor/ESC overheat Does not operate Poor range Vehicle moves forward or backward without input from user Car does not drive straight No steering or lack of steering Possible Cause Battery damaged/not charged Motor dirty Motor dirty Bind in drivetrain Vehicle battery is not charged ST. REV or TH.
Limited Warranty What this Warranty Covers Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase.
damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request is available at http://www.horizonhobby.com/content/servicecenter_render-service-center. If you do not have internet access, please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service.
FCC Information FCC Statement FCC ID: XNZKTH91802G This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
ECX203003 ECX202034 ECX202032 DYNS1203 ECX202032 ECX202034 49
REAR ASSEMBLY RÜCKENMONTAGE ASSEMBLAGE ARRIÈRE MONTAGGIO POSTERIORE ASSEMBLED GEBAUT ASSEMBLÉ ASSEMBLATO ECX202031 ECX206003 ECX202033 50
FRONT ASSEMBLY FRONTMONTAGE ASSEMBLAGE AVANT MONTAGGIO ANTERIORE ASSEMBLED GEBAUT ASSEMBLÉ ASSEMBLATO ECX202030 ECX202033 ECX206003 ECX202033 51
ECX201015 ECX201015 ECX206003 ECX201016 ECX206003 ECX201015 ECX201016 ECX206003 REAR RÜCKSEITE ARRIÈRE POSTERIORE ECX206003 ECX206003 52
FRONT VORDERSEITE AVANT ANTERIORE ECX206003 Scale Accessories | Zubehör skalieren Use a #48 (.076in/1.93mm) drill bit to punch holes for mounting detail parts. ECX200020 Verwenden Sie einen # 48 (1.93mm) Bohrer, um Löcher für die Montage von Einzelteilen zu stanzen. ECX200020 ECX200020 Accessoires d’échelle | Accessori in scala ECX200020 ECX200020 ECX200019 ECX40010 ECX200020 Utilisez un foret # 48 (1.93mm) pour percer des trous pour le montage des pièces de détail.
ECX200020 ECX200020 ECX200020 BLH8517EU REPLACEMENT PARTS / ERSATZTEILE / PIÈCES DE RECHANGE / PEZZI DI RICAMBIO Part # Description ECX201015 Chassis Supports Beschreibung Description Descrizione Supports de châssis Supporti telaio Ensemble d’arbre Antriebswellensatz Kit albero trasmissione ECX202034 Drive Shaft Set d’entraînement GETRIEBE: TRANSMISSION : TRASMISSIONE: ECX202032 TRANSMISSION: NIMH 4,8 V 220 MAH 4,8 V 220 MAH NIMH DYNB0007 4.
REPLACEMENT PARTS / ERSATZTEILE / PIÈCES DE RECHANGE / PEZZI DI RICAMBIO Part # Description ECX206003 HARDWARE SET SPMVX5801 FPV Antenna 4.3" FPV Video Beschreibung HARDWARESATZ FPV Antenna Description Descrizione ENSEMBLE DE MATÉRIEL SET BULLONERIA FPV Antenna FPV Antenna Moniteur vidéo FPV 4.3“ avec magnétoscope Monitor FPV con DVR 4,3’’ numérique SPMVM435 Monitor with DVR 4.
® ECX00018T1 | ECX00018T2 www.ecxrc.com © 2018 Horizon Hobby, LLC. ECX, the ECX logo, Barrage, Dynamite, and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC.
