® 1:12 GEN2 4WD 1.55 BRUSHED SCALER RTR ECX01013T1/T2 | ECX01013IT1/T2 INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D’UTILISATION MANUALE DI ISTRUZIONI Congratulations on your purchase of the ECX® Barrage® Gen2 4WD 1.55 Brushed Scaler. This model introduces you to the sport of RC driving. Herzlichen Glückwunsch zum kauf des ECX Barrage Gen2 4WD 1.55 Brushed Scaler. Dieses Modell ist der gelungende Einstieg in die Welt des RC Cars Sports.
EN NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit http://www.horizonhobby.com and click on the support tab for this product.
EN Wet Conditions Maintenance • Spray the bearings, drive train, fasteners and other metal parts with a water-displacing light oil or lubricant. Do not spray the motor. • Let the vehicle air dry before you store it. Water (and oil) may continue to drip for a few hours. • Increase the frequency of disassembly, inspection and lubrication of the following: • Front and rear axle hub assembly bearings. • All transmission cases, gears and differentials.
EN VEHICLE PREPARATIONS CHARGING THE VEHICLE BATTERY NOTICE: Never charge a battery in the vehicle or damage may result. 1. Connect the NiMH battery to the battery charger. 2. Connect the charger to an AC power outlet. 3. Allow the NiMH battery to charge for 9 hours. CHARGING WARNINGS WARNING: Failure to exercise caution while using this product and comply with the following warnings could result in product malfunction, electrical issues, excessive heat, FIRE, and ultimately injury and property damage.
EN TRANSMITTER CONTROLS Battery Level Indicator Reverse Switch Solid Red: Battery voltage is good (above 4V) Flashing Red: Battery voltage is critically low (below 4V). Replace transmitter batteries Allows you to change the direction of steering (ST. REV) and throttle (TH.
EN BINDING The included transmitter and receiver are bound at the factory. If you need to rebind, follow the instructions below. 1. Power OFF the receiver and transmitter. 2. Connect a fully charged battery to the ESC. 3. Insert the bind plug into the receiver’s binding pins and power ON the ESC. The receiver LED flashes. 4. Power ON the transmitter. 5. The receiver LED turns solid when binding in successful. You must rebind when binding the receiver to a different transmitter.
EN OPERATION • ALWAYS turn on your transmitter before you turn on the receiver in the vehicle. Always power off the receiver before turning your transmitter off. • ALWAYS operate your vehicle in a wide open area. Operating the vehicle in a small space or indoors can cause overheating at low speeds. Operating at low speed increases heat in the electronic speed control (ESC). Overheating can damage the vehicle and failure may result. WHEN YOU ARE FINISHED 1. Power off the ESC. 2.
EN MAINTENANCE SETTING THE GEAR MESH B The gear mesh has already been set at the factory. Setting the gear mesh is only necessary when changing motors or gears. You must remove the vehicle’s gear cover (A) to make this adjustment. C Proper gear mesh (how the gear teeth meet) is important to the performance of the vehicle. When the gear mesh is too loose, the spur gear could be damaged by the pinion gear of the motor. If the mesh is too tight, speed could be limited and the motor and ESC will overheat.
EN TROUBLESHOOTING GUIDE Problem Short Run Time Sluggish Action Controls Reversed Motor/ESC overheat Does Not Operate Poor Range The system will not connect The receiver goes into failsafe mode a short distance away from the transmitter The receiver quits responding during operation Receiver and transmitter are not bound Vehicle moves forward or backward without input from user Car does not drive straight No steering or lack of steering Possible Cause Battery damaged/not charged Motor dirty Motor dirty
EN LIMITED WARRANTY What this Warranty Covers Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase. that you may need any assistance. For questions or assistance, please visit our website at www.horizonhobby.
EN WARRANTY AND SERVICE CONTACT INFORMATION Country of Purchase United States of America Horizon Hobby Contact Information Horizon Service Center (Repairs and Repair Requests) Horizon Product Support (Product Technical Assistance) servicecenter.horizonhobby.com/ RequestForm/ productsupport@horizonhobby.com 877-504-0233 websales@horizonhobby.com 800-338-4639 service@horizonhobby.
Replacement Parts / Ersatzteile / Pièces de rechange / Pezzi di ricambio Part # Description Beschreibung Description Descrizione DYN1462 7.2V 900mAh NiMH Battery EC3 7.2V 1200mAh Ni-MH Akku, EC3 Batterie Ni-Mh 7.2V 1200mA, prise EC3 Batteria 7.
Optional Parts / Optionale Teile / Liste des options / Elenco parti opzionali Part # Description Beschreibung Description Descrizione DYN1471 7.2V 1750mAh NiMH 6C Flat Battery, EC3: Minis Flache Akkus Ni-MH 7,2V 1750mA, EC3: Mini 1/18 Mini 1/18: Batterie plate Ni-MH 7,2V 1750mA, prise EC3 Batteria piatta 6C NiMH 1750 mAh 7,2 V, EC3: Minis DYN1473 7.
PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÈCES | ESPLOSO DEL MODELLO CON REFERENZA PEZZI ECX13009 ECX216003 DYNS2210 DYNS1462 ECX211021 ECX211021 SPMS602 ECX221000 ECX216003 ECX221000 ECX216003 ECX216003 ECX216003 ECX211020 ECX211016 ECX211018 ECX211018 ECX216003 ECX216003 ECX216003 ECX211014 ECX216003 ECX216003 ECX216003 ECX211020 ECX211015 ECX224000 ECX211018 ECX213002 ECX216003 ECX211018 ECX216003 ECX216003 ECX216003 ECX211015 ECX216003 ECX211017 ECX224000 ECX213002 EC
PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÈCES | ESPLOSO DEL MODELLO CON REFERENZA PEZZI ECX212018 ECX222001 ECX212021 ECX212021 ECX222003 DYNS1206 DYNS1206 FRONT AXLE | VORDERACHSE | HINTERACHSE | ASSE ANTERIORE ECX222000 ECX212021 ECX212020 ECX217001 ECX212010 ECX212009 ECX217001 ECX216003 ECX216003 ECX222000 ECX222002 ECX224000 ECX216003 ECX216003 ECX217001 ECX224000 ECX212028 ECX216003 ECX212027 ECX212027 ECX212027 ECX217001 ECX221000 ECX216003 ECX221000 REAR AXLE | ESSI
® ECX01013T1/T2 www.ecxrc.com © 2018 Horizon Hobby, LLC. ECX, the ECX logo, Barrage, Dynamite, Speedpack, Prophet, Tazer, EC3, and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc.
