i Preface Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. Version 2.0 Disclaimer The information in this document is subject to change without notice.
ii Declaration of Conformity This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: • • This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. Canadian Department of Communications This class B digital apparatus meets all requirements of the Canadian Interference-causing Equipment Regulations.
iii TABLE OF CONTENTS Preface i Chapter 1 1 Introducing the Motherboard 1 Introduction................................................................................................1 Features.......................................................................................................2 Motherboard Components.......................................................................4 Chapter 2 7 Installing the Motherboard 7 Safety Precautions.....................................................
iv Integrated Peripherals.................................................................36 Power Management Setup...........................................................40 PNP/PCI Configurations.............................................................43 PC Health Status..........................................................................44 Frequency/Voltage Control..........................................................44 Load Fail-Safe Defaults..............................................
1 Chapter 1 Introducing the Motherboard Introduction Thank you for choosing this motherboard of great performance and with enhanced function. This motherboard is designed to fit the AMD K8 processors in the 754-pin package. Two 184 pin unbuffered DDR SDRAM DIMM sockets support up to 2 GB in total memory. Based on the uATX form factor, this motherboard incorporates the following chipsets: K8M800 chipset family Northbridge and VT8237R Southbridge chipsets.
2 Feature Processor The motherboard uses a 754-pin socket that carries the following features: • Supports AMD K8 processors with HyperTransport Technology HyperTransport Technology is a point-to-point link between two devices, it enables integrated circuits to exchange information at much higher speeds than currently available interconnect technologies.
3 Expansion Options The motherboard comes with the following expansion options: • • • • • Three 32-bit PCI slots One AGP slot Two IDE connectors which support four IDE devices One floppy disk drive interface Two 7-pin SATA connectors This motherboard supports Ultra DMA bus mastering with transfer rates of 133/100/66 MB/s.
4 Motherboard Components Introducing the Motherboard
5 Table of Motherboard Components LABEL 1 CPU Socket COMPONENT Socket 754 for AMD K8 processor 2 3 4 5 6 7 8 CPU cooling fan connector 184-pin DDR SDRAM slots Standard 20-pin ATX power connector Floppy disk drive connector Primary/Secondary IDE connector Serial ATA connectors Front panel switch/LED header CPUFAN DIMM1~2 ATX_POWER FDD IDE1/IDE2 SATA1~SATA2 PANEL1 9 CLR_CMOS 10 USB3 ~ 4 Clear CMOS jumper Front Panel USB headers 11 12 13 14 15 16 Front panel audio header SPDIF out header CD-in connec
6 Memo Introducing the Motherboard
7 Chapter 2 Installing the Motherboard Safety Precautions • • • • • Follow these safety precautions when installing the motherboard Wear a grounding strap attached to a grounded device to avoid damage from static electricity Discharge static electricity by touching the metal case of a safely grounded object before working on the motherboard Leave components in the static-proof bags they came in Hold all circuit boards by the edges.
8 Do not over-tighten the screws as this can stress the motherboard. Checking Jumper Settings This section explains how to set jumpers for correct configuration of the motherboard. Setting Jumpers Use the motherboard jumpers to set system configuration options. Jumpers with more than one pin are numbered. When setting the jumpers, ensure that the jumper caps are placed on the correct pins. The illustrations show a 2-pin jumper. When the jumper cap is placed on both pins, the jumper is SHORT.
9 Checking Jumper Settings The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled. Jumper Settings Jumper Type Description CLR_CMOS 3-pin CLEAR CMOS Setting (default) 1-2: NORMAL 2-3: CLEAR 1 CLR_CMOS Before clearing the CMOS, make sure to turn the system off.
10 Connecting Case Components After you have installed the motherboard into a case, you can begin connecting the motherboard components. Refer to the following: 1 2 3 4 5 Connect the CPU cooling fan cable to CPU_FAN. Connect the case cooling fan connector to SYS_FAN. Connect the case switches and indicator LEDs to the PANEL1. Connect the standard power supply connector to ATX_POWER. Connect the auxiliary case power supply connector to ATX_12V.
11 ATX_POWER: ATX 20-pin Power Connector Pin Signal Name Pin Signal Name 1 2 +3.3V +3.3V +3.3V 11 12 3 Ground 13 Ground 4 +5V 14 PS ON# 5 6 7 8 9 10 Ground +5V Ground 15 16 17 18 19 20 Ground Ground Ground PWRGD +5VSB +12V -12V -5V +5V +5V Front Panel Header The front panel connector (PANEL1) provides a standard set of switch and LED header commonly found on ATX or micro-ATX cases.
12 Reset Switch Supporting the reset function requires connecting pin 5 and 7 to a momentary-contact switch that is normally open. When the switch is closed, the board resets and runs POST. Power Switch Supporting the power on/off function requires connecting pins 6 and 8 to a momentarycontact switch that is normally open. The switch should maintain contact for at least 50 ms to signal the power supply to switch on or off. The time requirement is due to internal debounce circuitry.
13 CPU Installation Procedure The following illustration shows CPU installation components. 1 2 3 4 5 Install your CPU. Pull up the lever away from the socket and lift up to 90-degree angle. Locate the CPU cut edge (the corner with the pin hold noticeably missing). Align and insert the CPU correctly. Press the lever down and apply thermal grease on top of the CPU. Put the CPU Fan down on the retention module and snap the four retention legs of the cooling fan into place.
14 Installation Procedure Refer to the following to install the memory modules. 1 2 3 4 5 6 This motherboard supports unbuffered DDR SDRAM only. Push the latches on each side of the DIMM slot down. Align the memory module with the slot. The DIMM slots are keyed with notches and the DIMMs are keyed with cutouts so that they can only be installed correctly. Check that the cutouts on the DIMM module edge connector match the notches in the DIMM slot.
15 Table A: Unbuffered DIMM Support for 754-pin Number of DIMMs 5 DIMM 1 4.1.
16 Table B: DDR (memory module) QVL (Qualified Vendor List) The following DDR400 memory modules have been tested and qualified for use with this motherboard.
17 Installing a Hard Disk Drive/CD-ROM/SATA Hard Drive This section describes how to install IDE devices such as a hard disk drive and a CD-ROM drive. About IDE Devices Your motherboard has a primary and secondary IDE channel interface (IDE1 and IDE2). An IDE ribbon cable supporting two IDE devices is bundled with the motherboard. You must orient the cable connector so that the pin1 (color) edge of the cable correspoinds to the pin 1 of the I/O port connector.
18 About SATA Connectors Your motherboard features two SATA connectors supporting a total of two drives. SATA refers to Serial ATA (Advanced Technology Attachment) is the standard interface for the IDE hard drives which are currently used in most PCs. These connectors are well designed and will only fit in one orientation. Locate the SATA connectors on the motherboard (see page 21) and follow the illustration below to install the SATA hard drives.
19 Installing a Floppy Diskette Drive The motherboard has a floppy diskette drive (FDD) interface and ships with a diskette drive ribbon cable that supports one or two floppy diskette drives. You can install a 5.25-inch drive and a 3.5-inch drive with various capacities. The floppy diskette drive cable has one type of connector for a 5.25-inch drive and another type of connector for a 3.5-inch drive.
20 AGP Slot The AGP slot is used to install a graphics adapter that supports the 8X/4X AGP specification. It is AGP 3.0 compliant. PCI Slot It is equipped with three standard PCI slots. PCI stands for Peripheral Component Interconnect and is a bus standard for expansion cards, which for the most part, is a supplement of the older ISA bus standard. The PCI slots on this board are PCI v2.2 compliant. Before installing an add-on card, check the documentation for the card carefully.
21 Connecting Optional Devices Refer to the following for information on connecting the motherboard’s optional devices: SPDIFO1: SPDIF out header This is an optional header that provides an S/PDIF (Sony/Philips Digital Interface) output to digital multimedia device through optical fiber or coaxial connector.
22 USB3/USB4: Front Panel USB header The motherboard has four USB ports installed on the rear edge I/O port array. Additionally, some computer cases have USB ports at the front of the case. If you have this kind of case, use auxiliary USB connector to connect the front-mounted ports to the motherboard.
23 Connecting I/O Devices The backplane of the motherboard has the following I/O ports: PS2 Mouse Use the upper PS/2 port to connect a PS/2 pointing device. PS2 Keyboard Use the lower PS/2 port to connect a PS/2 keyboard. Parallel Port (LPT1) Use LPT1 to connect printers or other parallel communications devices. Serial Port (COM1) Use the COM port to connect serial devices such as mice or fax/modems. LAN Port Connect an RJ-45 jack to the LAN port to connect your computer to the Network.
24 Memo Installing the Motherboard
25 Chapter 3 Using BIOS About the Setup Utility The computer uses the latest Award BIOS with support for Windows Plug and Play. The CMOS chip on the motherboard contains the ROM setup instructions for configuring the motherboard BIOS. The BIOS (Basic Input and Output System) Setup Utility displays the system’s configuration status and provides you with options to set system parameters. The parameters are stored in battery-backed-up CMOS RAM that saves this information when the power is turned off.
26 Press DEL to enter SETUP Pressing the delete key accesses the BIOS Setup Utility: Phoenix-AwardBIOS CMOS Setup Utility: Standard CMOS Features Advanced BIOS Features Frequency/Voltage Control Load Fail-Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup Set User Password PnP/PCI Configurations PC Health Status Save & Exit Setup Exit Without Saving Esc: Quit F10: Save & Exit Setup : Select Item Time, Date, Hard D
27 Updating the BIOS You can download and install updated BIOS for this motherboard from the manufacturer’s Web site. New BIOS provides support for new peripherals, improvements in performance, or fixes for known bugs. Install new BIOS as follows: 1 2 3 4 5 6 7 8 If your motherboard has a BIOS protection jumper, change the setting to allow BIOS flashing. If your motherboard has an item called Firmware Write Protect in Advanced BIOS features, disable it.
28 Standard CMOS Features This option displays basic information about your system. Phoenix-AwardBIOS CMOS Setup Utility Standard CMOS Features Date (mm:dd:yy) Wed, Sep 14 2005 Time (hh:mm:ss) 9 : 33 : 26 IDE Channel 0 Master IDE Channel 0 Slave IDE Channel 1 Master IDE Channel 1 Slave Drive A Drive B Video Halt On Item Help Menu Level Change the day, month, year and century [1.44M, 3.5 in.
29 IDE Channel 0/1/2 Master/Slave/Extended IDE Drive(Auto) Leave this item at Auto to enable the system to automatically detect and configure IDE devices on the channel. If it fails to find a device, change the value to Manual and then manually configure the drive by entering the characteristics of the drive in the items described below. Please noted that if you choose IDE Channel 2/3 Master, the item may change to Extended IDE Drive.
30 Advanced BIOS Features This option defines advanced information about your system. Phoenix-AwardBIOS CMOS Setup Utility Advanced BIOS Features BIOS Protect ATA 66/100 IDE Cable Msg.
31 CPU Internal Cache (Enabled) All processors that can be installed in this motherboard use internal level 1 (L1) cache memory to improve performance. Leave this item at the default value for better performance. External Cache (Enabled) Most processors that can be installed in this system use external level 2 (L2) cache memory to improve performance. Leave this item at the default value for better performance.
32 APIC Mode (Enabled) This item allows you to enable or disable the APIC (Advanced Programmable Interrupt Controller) mode. APIC provides symmetric multi-processing (SMP) for systems, allowing support for up to 60 processors. OS Select For DRAM > 64MB (Non-OS2) This item is only required if you have installed more than 64 MB of memory and you are running the OS/2 operating system. Otherwise, leave this item at the default. HDD S.M.A.R.T Capability [Disabled] The S.M.A.R.T.
33 Advanced Chipset Features These items define critical timing parameters of the motherboard. You should leave the items on this page at their default values unless you are very familiar with the technical specifications of your system hardware. If you change the values incorrectly, you may introduce fatal errors or recurring instability into your system.
34 AGP Driving Control (Auto) This item is used to signal driving current on AGP cards to auto or manual. Some AGP cards need stronger than normal driving current in order to operate. We recommend that you set this item to the default. • AGP Driving Value: When AGP Driving Control is to set Manual, use this item to set the AGP current driving value. AGP Fast Write (Disabled) This item lets you enable or disable the caching of display data for the video memory of the processor.
35 • CAS# latency (Tcl): This item determines the operation of DDR SDRAM memory CAS (column address strobe). It is recommended that you leave this item at the default value. The 2T setting requires faster memory that specifically supports this mode. User Config mode(Auto) This item has the capacity to automatically detect all of the fllowing fieldsdefault values. This item is set to [Auto] by default. When setting to[Manual], the following items are adjustable.
36 PCI1/2 Post Write (Enabled) When enabled, writes from the CPU to PCU bus are buffered, to compensate for the speeddifferences between the CPU and PCI bus. When disabled, the writes are not buffered and theCPU must wait until the write is complete before starting another write cycle. PCI Delay Transaction (Disabled) The motherboard’s chipset has an embedded 32-bit post write buffer to support delay transactions cycles. Select Enabled to support compliance with PCI specification version 2.1.
37 VIA OnChip IDE Device (Press Enter) Scroll to this item and press to view the following screen: Phoenix-AwardBIOS CMOS Setup Utility VIA OnChip IDE Device OnChip VIA SATA SATA Mode IDE DMA transfer access OnChip IDE Channel0 OnChip IDE Channel1 IDE Prefetch Mode Primary Master PIO Primary Slave PIO Secondary Master PIO Secondary Slave PIO Primary Master UDMA Primary Slave UDMA Secondary Master UDMA Secondary Slave UDMA IDE HDD Block Mode [Enabled] [IDE] [Enabled] [Enabled] [Enabled] [Enabled] [
38 VIA OnChip PCI Device (Press Enter) Scroll to this item and press to view the following screen: Phoenix-AwardBIOS CMOS Setup Utility VIA OnChip PCI Device AC97 Audio MC97 Modem OnBoard LAN OnBoard LAN Boot ROM OnChip USB Controller USB 2.
39 SuperIO Device (Press Enter) Scroll to this item and press to view the following screen: Phoenix-AwardBIOS CMOS Setup Utility SuperIO Device Onboard FDC Controller Onboard Serial Port 1 Onboard Serial Port 2 UART Mode Select UR2 Duplex Mode Onboard Parallel Port Parallel Port Mode ECP Mode Use DMA [Enabled] [3F8/IRQ4] [2F8/IRQ3] [Normal] [Half] [378/IRQ7] [ECP] [3] Item Help Menu Level : Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help F5:Previous Values F6:Fail-Safe Defa
40 Power Management Setup This option lets you control system power management. The system has various powersaving modes including powering down the hard disk, turning off the video, suspending to RAM, and software power down that allows the system to be automatically resumed by certain events.
41 Soft-Off by PWRBTN (Instant-Off) Under ACPI (Advanced Configuration and Power management Interface) you can create a software power down. In a software power down, the system can be resumed by Wake Up Alarms. This item lets you install a software power down that is controlled by the power button on your system. If the item is set to Instant-Off, then the power button causes a software power down. If the item is set to Delay 4 Sec.
42 PCI Master (OFF) When set to Off, any PCI device set as the Master will not power on the system. Resume by PCI PME(Enabled) Use this item to enable PCI activity to wakeup the system from a power saving mode. Resume by Ring (Disabled) Use this item to enable modem activity to wakeup the system from a power saving mode. RTC Alarm Resume (Disabled) When set to Enabled, additional fields become available and you can set the date (day of the month), hour, minute and second to turn on your system.
43 PNP/PCI Configurations These options configure how PnP (Plug and Play) and PCI expansion cards operate in your system. Both the the ISA and PCI buses on the motherboard use system IRQs (Interrup ReQuests) and DMAs (Direct Memory Access). You must set up the IRQ and DMA assignments correctly through the PnP/PCI Configurations Setup utility for the motherboard to work properly.
44 PC Health Status On motherboards that support hardware monitoring, this item lets you monitor the parameters for critical voltages, temperatures and fan speeds. Phoenix-AwardBIOS CMOS Setup Utility PC Health Status Shutdown Temperature [Disabled] Vcore V DIMM Vcc 3.
45 CPU Clock (200MHz) Use the CPU Host Clock to set the frontside bus frequency for the installed processor (Min 200 MHz, Max 232 MHz) Load Fail-Safe Defaults This option opens a dialog box that lets you install fail-safe defaults for all appropriate items in the Setup Utility: Press and the to install the defaults. Press and then to not install the defaults. The fail-safe defaults place no great demands on the system and are generally stable.
46 Save & Exit Setup Highlight this item and press to save the changes that you have made in the Setup Utility and exit the Setup Utility. When the Save and Exit dialog box appears, press to save and exit, or press to return to the main menu. Exit Without Saving Highlight this item and press to discard any changes that you have made in the Setup Utility and exit the Setup Utility.
47 Chapter 4 Using the Motherboard Software About the Software CD-ROM The support software CD-ROM that is included in the motherboard package contains all the drivers and utility programs needed to properly run the bundled products. Below you can find a brief description of each software program, and the location for your motherboard version. More information on some programs is available in a README file, located in the same directory as the software.
48 Setup Tab Setup Click the Setup button to run the software installation program. Select from the menu which software you want to install. Browse CD The Browse CD button is the standard Windows command that allows you to open Windows Explorer and show the contents of the support CD. Before installing the software from Windows Explorer, look for a file named README.TXT, INSTALL.TXT or something similar. This file may contain important information to help you install the software correctly.
49 Running Setup Follow these instructions to install device drivers and software for the motherboard: 1. Click Setup. The installation program begins: The following screens are examples only. The screens and driver lists will be different according to the motherboard you are installing. The motherboard identification is located in the upper left-hand corner. 2. Click Next.
50 3. Check the box next to the items you want to install. The default options are recommended. 4. Click Next run the Installation Wizard. An item installation screen appears: 5. Follow the instructions on the screen to install the items. Drivers and software are automatically installed in sequence. Follow the onscreen instructions, confirm commands and allow the computer to restart a few times to complete the installation. Manual Installation Insert the CD in the CD-ROM drive and locate the PATH.
51 AWARD Flash Utility This utility lets you erase the system BIOS stored on a Flash Memory chip on the motherboard, and lets you copy an updated version of the BIOS to the chip. Proceed with caution when using this program. If you erase the current BIOS and fail to write a new BIOS, or write a new BIOS that is incorrect, your system will malfunction. Refer to Chapter 3, Using BIOS for more information.
52 Memo Using the Motherboard Software
53 Chapter 5 VIA VT8237 R SATA RAID Setup Guide VIA RAID Configurations The motherboard includes a high performance Serial ATA RAID controller integrated in the VIA VT8237R Southbridge chipset. It supports RAID 0, RAID 1 and JBOD with two independent Serial ATA channels. RAID: (Redundant Array of Independent Disk Drives) use jointly several hard drives to increase data transfer rates and data security.
54 1 2 3 4 5 6 7 Install the Serial ATA hard disks into the drive bays. Connect one end of the Serial ATA cable to the motherboard’s primary Serial ATA connector (SATA1). Connect the other end of Serial ATA cable to the master Serial ATA hard disk. Connect one end of the second Serial ATA cable to the motherboard’s secondary Serial ATA connector (SATA2). Connect the other end of Serial ATA cable to the secondary Serial ATA hard disk. Connect the Serial ATA power cable to the power connector on each drive.
55 Create Array 1 In the VIA RAID BIOS utility main menu, select Create Array then press the key. The main menu items on the upper-left corner of the screen are replaced with create array menu options. RAID 0 for performance 1 Select the second option item Array Mode, then press the key. The RAID system setting pop-up menu appears. 2 Select RAID 0 for performance from the menu and press .
56 5 Select Start Create Process and press to setup hard disk for RAID system. The following confirmation appears: The same confirmation message appears when the Auto Setup for Performance option is selected. Press “Y” to confirm or “N” to return to the configuration options. RAID 1 for data protection 1 Select the second option item Array Mode, then press the key. The RAID system setting pop-up menu appears. 2 Select RAID 1 for data protection from the menu and press .
57 Delete Array 1 2 In the VIA RAID BIOS utility main menu, select Delete Array then press the key. The focus is directed to the list of channel used for IDE RAID arrays. Press the key to select a RAID array to delete. The following confirmation message appears. Press “Y” to confirm or “N” to return to the configuration options. Select Boot Array 1 2 In the VIA RAID BIOS utility main menu, select Select Boot Array then press the key.
58 Duplicate Critical RAID 1 Array When booting up the system, BIOS will detect if the RAID 1 array has any inconsistencies between user data and backup data. If BIOS detects any inconsistencies, the status of the disk array will be marked as critical, and BIOS will prompt the user to duplicate the RAID 1 in order to ensure the backup data consistency with the user data. If user selects Continue to boot, it will enable duplicating the array after booting into OS.
59 1. Power off and Check the Failed Drive: This item turns off the computer and replaces the failed hard drive with a good one. If your computer does not support APM, you must turn off your computer manually. After replacing the hard drive, boot into BIOS and select Choose replacement drive and rebuild to rebuild the broken array. 2. Destroy the Mirroring Relationship: This item cancels the data mirroring relationship of the broken array.
60 Installing RAID Software & Drivers Install Driver in Windows OS New Windows OS (2000/XP/NT4) Installation The following details the installation of the drivers while installing Windows XP. 1 2 3 4 5 6 Start the installation: Boot from the CD-ROM. Press F6 when the message “Press F6 if you need to install third party SCSI or RAID driver’ appears. When the Windows Setup window is generated, press S to specify an Additional Device(s).
61 Installation of VIA SATA RAID Utility The VIA SATA RAID Utility is the software package that enables high-performance RAID 0 arrays in the Windows*XP operating system. This version of VIA SATA RAID Utility contains the following key features: • • • Insert the Serial ATA RAID driver for Windows XP VIA SATA RAID utility RAID0 and RAID1 functions ECS CD and click on the Setup to install the software. The InstallShield Wizard will begin automatically for installation.
62 Put a check mark in the check box to install the feature you want. Then click Next button to proceed the installation. Using VIA RAID Tool Once the installation is complete, go to Start---> Programs---> VIA---> raid_tool.exe to enable VIA RAID Tool. After the software is finished installation, it will automatically started every time Windows is initiated. You may double-click on the icon shown in the system tray of the tool bar to launch the VIA RAID Tool utility.
63 The main interface is divided into two windows and the toolbar above contain the main functions. Click on these toolbar buttons to execute their specific functions. The left windowpane displays the controller and disk drives and the right windowpane displays the details of the controller or disk drives.
64 Click on the plus (+) symbol next to Array 0--RAID 0 to see the details of each disk. You may also use the same or button to view the statuses of Array 0-- RAID 1.
65 Click on the plus (+) symbol next to Array 0; RAID 1 to see the details of each disk.
66 Memo VIA VT8237 SATA RAID Setup Guide
Cette carte mère utilise un socket de 754 broches ayant les caractéristiques suivantes : • Prend en charge les processeurs AMD K8 avec la Technologie Hyper Transport La Technologie HyperTransport est une liaison point à point entre deux matériels, elle permet à des circuits intégrés d’échanger des informations à des vitesses bien plus élevées que ne le permettent les technologies à interconnexions actuellement disponibles.
Français Options d’extension La carte mère est livrée avec les options d’extensions suivantes: • Trois logements PCI 32 bits • Un logement AGP • Deux en-tetes demi-hauteur supportant quatre canaux IDE • Une interface de lecteur de disquette • Deux connecteurs SATA à 7 broches La carte mère prenant en charge la maîtrise de bus UltraDMA avec vitesses de transfert de 133/100/66 Mo/s.
Dieses Motherboard verwendet einen 939-Pin Socket mit den folgenden Eigenschaften: • Unterstützt AMD K8-Prozessoren mit HyperTransport-Technologie HyperTransport Technologie ist ein Punkt-zu-Punkt Link zwischen zwei Geräten. Es ermöglicht integrierten Schaltkreisen einen Informationsaustausch mit wesentlich höherer Geschwindigkeit als bei gängigen Interconnect-Technologien.
Erweiterungsoptionen Deutsche Das Motherboard bietet die folgenden Erweiterungsoptionen: • Drei 32-bit PCI-Steckplätze • Ein AGP-Slot • Zwei IDE-Stecker, die vier IDE-Kanäle unterst tzen • Ein Steckplatz für ein Diskettenlaufwerk • Zwei 7-Pin SATA-Stecker Die Motherboard unterstützt UltraDMA Bus Mastering mit einer Übertragungsrate von 133/100/66 MB/Sek.
La scheda madre utilizza una presa a 754 pin che offre le seguenti caratteristiche: • Supporto processore AMD K8 con tecnologia di HyperTransport La tecnologia HyperTransport rappresenta un collegamento Point-to-point tra due periferiche tramite l’utilizzo di circuiti integrati ad una velocità di molto superiore a quelle delle tecnologie attuali.
Opzioni di espansione Italiano La scheda madre è dotata delle seguenti opzioni di espansione: • Tre slot PCI a 32 bit • Uno slot AGP • Due collettori IDE che supportano quattro dispositivi IDE • Un’interfaccia per unità disco floppy • Due connettori SATA a 7 pin La scheda madre supporta bus master UltraDMA con tasso di trasferimento di 133/100/66 MB/s.
Característica Procesador Esta placa principal usa un zócalo de 754-pin que lleva las sigtes. características: • Soporta procesadores AMD K8 con HyperTransport Technology Chipset El chipset VIA K8M800 Northbridge (NB) y VIA VT8237 Southbridge (SB) se basan de una arquitectura innovadora y escalable con fiabilidad y rendimiento comprobados.
Opciones de Expansión La placa principal viene con las sigtes. opciones de expansión: • Tres ranuras 32-bit PCI • Una ranura AGP • Dos conectores IDE que soporta hasta cuatro dispositivos IDE • Una interfaz de la unidad de disco floppy • Dos conectores SATA de 7-pin La placa principal soporta el mastering de bus UltraDMA con índices de transferencia de 133/100/66 MB/s. Español LAN Abordo (optativo) Esta placa principal puede soportar uno de los sigtes.
Características Processador Esta motherboard usa uma ficha de 754 pin que possui as seguintes características: • Suporta processador AMD K8 com tecnologia de HyperTransport Tecnologia de HyperTransport Té um link ponto-a-ponto entre dois dispositivos, permite circuitos integrados para trocar informação a velocidades muito mais elevadas que as disponíveis actualmente em tecnologias de interconexão.
Opções de Expansão A motherboard é fornecida com as seguintes opções de expansão: • Três slots PCI de 32 bit • Uma ranhura AGP • Dois conectores IDE que suportam até quatro dispositivos IDE • Um interface com drive de disco flexível • Dois conectores SATA de 7 pin A motherboard suporta um domínio bus UltraDMA bus com taxas de Transferência de 133/100/66 MB/s.
機能 プロセッサ このマザーボードには、次の機能を持った754ピンソケットが一つあります： • HyperTransport技術を導入したAMD K8プロセッサに対応します HyperTransport 技術とは、二つのデバイスを1対1( point-to-point)で接続する技術 であり、従来のインターコネクト技術に比較して、集積回路同士の情報交換を高速化しま す。 チップセット K8M800 (NB) • • • VT8237R (SB) • • • • • 800/600/400/200 MHz クロック率で、同期双方向の 1600/1200/800/400 MT/秒 の“Double Data Rate”動作を 提供 66 MHz仕様である8X /4X 転送モード対応 V-Link Host インター フェースを導入し、トータルで533ＭB/秒の帯域幅を実現 AGP v3.0 でFast Write対応の8X/4X 転送モードを提供 16ビットの 66 MHz V-Link クライアントインターフェースを サポートし、トータル帯域幅 1066 MB/秒まで可能 33MHzでのPCI2.
拡張オプション 本マザーボードでは、次の拡張機能が利用できます。 • • • • • AGP スロットが1つ 32ビットPCI 互換性スロットが3つ IDEコネクタ X2 (計4つのIDEチャネルをサポート) フロッピーディスクドライブインターフェイス が1つ 7ピンSATAコネクタ が2つ このマザーボードは、133/100/66 MB/秒の転送速度でのUltra DMAバスマスタリング をサポートします。 オンボードLAN (オプション) 日本語 当マザーボードは次のLANチップセットのいずれかを搭載しております： • シングルチップ100Base-TX/10Base-T 物理層ソリューションを採用 • デュアル100/10 Mbpsをサポート • 半/全二重の動作可能 • イーサーネットコントローラのMII インターフェースに対応 • MIIインターフェース: 構成と状態を表示 • 自動折衝機能：10 / 100、全 /半二重 • 適用可能のIEEE 802.
특성 프로세서 본 마더보드는 다음과 같은 특성을 지닌 754 핀 소켓을 사용합니다: • HyperTransport 기술의 AMD K8 프로세서 지원 HyperTransport 기술은 두 장치 사이의 point-to-point 링크로, 집적 회로가 기존의 인터커넥트 기술보다 훨신 빠른 속도로 정보를 교환할 수 있게 한다. 칩셋 VIA K8M800 Northbridge (NB) 및 VIA VT8237R Southbridge (SB) 칩셋은 혁신적 이고 범위성을 지닌 아키텍쳐를 기반으로 인정된 신뢰성과 성능을 지닌다. • • • VT8237R (SB) • • • • • 클록 속도 800/600/400/200 MHz, “Double Data Rate” 방식으로 양방향 동시 1600/1200/800/400 MT/s 지원 66 MHz, 8X / 4X 전송 모드, 총 대역폭 533MB/s의 VLinkHost 인터페이스 지원 AGP v3.
확장 옵션 본 마더보드의 확장 옵션은 다음과 같다: • 32-bit PCI 슬롯 3 개 • AGP 슬롯 1 개 • 4 개의 IDE 장치를 지원하는 IDE 헤더 2 개 • 플로피 디스크 드라이브 인터페이스 1 개 • 7 핀 SATA 커넥터 2 개 마더보드는 전송 속도 133/100/66 MB/s의 UltraDMA 버스 마스터링을 지원한다. 보드 내장 LAN (선택 사항) 본 마더보드는 다음과 같은 LAN 칩셋을 지원합니다: • 싱글 칩 100Base-TX/10Base-T 물리적 계층 솔루션 • 듀얼 스피드 100/10 Mbps • Half/Full Duplex • 이더넷 컨트롤러를 위한 MII 인터페이스 • 구성 및 상태 MII 인터페이스 • Auto Negotiation: 10 / 100, Full / Half Duplex • IEEE 802.
功能 處理器 本主機板配備具有如下功能的939針插槽: • 支援採用HyperTransport 技術之AMD K8處理器 HyperTransport技術為以點對點方式連接兩台設備的技術，藉此，積體電路間能夠以後 高於現有各種內部連接技術(interconnect technology)技術的速度來交換資訊。 晶片組 VT8237R (SB) • • • • • 支援16-bit 66 MHz V-Link HOST介面，總頻寬高達 1066MB/秒 相容於33MHz的PCI v2.2規格(支援6個PCI主控器) 內建有雙通道Ultra 133/100/66主控模式EIDE控制器 USB2.0控制器(支援8個USB2.0/1.1埠) 內建有支援PS2滑鼠之鍵盤控制器 記憶體 • • • 支援 DDR400/333/266/200記憶體 2個無緩衝的 2.5V 184針DIMM插槽 最大容量 2 GB AC’97 音訊編解碼器 • • • • • • • • • • • 相容於 AC’97 Rev2.
擴充選項 本主機板包括下列擴充選項： • 3個 32-bit PCI 插槽 • 1個 AGP插槽 • 2個 IDE 接頭，支援 4個 IDE 裝置 • 1個軟碟機介面 • 2個7針SATA插頭 本主機板支援傳輸率133/100/66 MB/秒下的Ultra DMA 匯流排主控功能。 內建區域網路 (選購) 本主機板搭載有如下其中一種LAN晶片組： • 採用單晶片100Base-TX/10Base-T 實體層解決方案 ‧ 採用100/10 Mbps雙速 ‧ 全 / 半雙工 ‧ 乙太網路控制器之MII介面 ‧ MII 介面，便於組態調整及顯示狀態 ‧ 自動協商功能：10 / 100、及全 / 半雙工 • 符合所有適用之IEEE 802.
功能 处理器 主板使用一个 754-pin 插座，此插座具有以下特点： • 支持AMD K8 处理器以HyperTransport 技术 HyperTransport 技术是一种在两台设备间进行点到点连接的技术，它可以让集成电路 使用比当前互连技术更高的速度进行信息交换。 芯片组 VIA K8M800 北桥 (NB) 和 VIA VT8237R 南桥 (SB) 芯片组是基于一种新型的、可 扩展的架构，能提供已经证明的可靠性和高性能。 • • • VT8237R (SB) • • • • • • • 800/600/400/200 MHz 时钟频率，“双数据速率”工作，双向 并发传输速率可达 1600/1200/800/400 MT/s 支持 66 MHz 8X/4X 传输模式，支持 V-Link 主控接口，总带 宽可达 533MB/sec 符合 AGP v3.0 标准，8X/4X 传输模式，支持快写 支持总带宽为 1066MB/sec 的 16 位 66MHz V-Link 主机接 口 符合 33 MHz 下的 PCI 2.
扩展选项 此主板提供如下扩展选项： • 3 个 32 位 PCI 扩展插槽 • 1 个AGP 槽 • 2 个 IDE 接口，可支持 4 个 IDE 设备 • 1 个软驱接口 • 2 个 7-pin SATA 接口 主板支持 Ultra DMA 总线控制，传输速率可达 133/100/66MB/s。 Onboard LAN（可选） 此主板支持以下任何一种 LAN 芯片组： • 单芯片 100Base-TX/10Base-T 物理层解决方案 • 双速-100/10 Mbps • 半双工和全双工 • 以太网控制器的 MII 接口 • 到配置&状态的 MII 接口 • 自动协商：10/100，全双工/半双工 • 符合所有相应的 IEEE 802.
Характеристики Процессор Плата использует сокет 754-pin и обладает следующими характеристиками: • Поддерживает процессоры AMD K8 с технологией HyperTransport Technology Технология HyperTransport обеспечивает связь двух устройств по протоколу point-topoint, позволяя гораздо более быстрый обмен информацией между интегральными микросхемами, чем тот, который обеспечивается существующими технологиями.
Возможности расширения Существуют следуюшие опции расширения данной материнской платы: • Три 32-битовых слота PCI • Один слот AGP • Два разъема IDE с поддержкой до четырех устройств IDE • Один разъем для накопителя на гибких дисках • Два разъема 7-pin SATA Плата поддерживает технологию захвата управления шиной UltraDMA bus mastering со скоростью передачи данных 133/100/66 МБ/сек.
Cechy Procesor Ta płyta główna zaopatrzona jest w podstawkę dla procesorów z 754 nóżkami i charakteryzuje się następującymi cechami: • Obsłguje procesory K8 firmy AMD oparte na technologii HT Technologia HiperTransportu jest protokołem komunikacji między dwoma urządzeniami, który umożliwia układom zcalonym wymieniać informację z dużo większymi szybkościami niż dotychczas stosowane technologie wzajemnych połączeń.
Możliwości rozbudowy Płyta głwna wyposażona jest w następujące gniazda: • Trzy 32-bitowe gniazda PCI • Jedno gniazdo AGP • Dwa złącza IDE mogące obsłużyć do czterech urządzeń IDE • Jedno złącze obsługujące stacje dyskietek • Dwa 7-nóżkowe złącza SATA Płyta główna obsługuje szynę UltraDMA z szybkością transferu 133/100/66 MB/s.
Vlastnosti Procesor Tato základní deska využívá 754kolíkovou patici nabízející následující vlastnosti: • Podporuje procesory AMD K8 s technologií HyperTransport Technologie HyperTransport je přímým spojením mezi dvěma zařízeními, umožňující integrovaným obvodům výměnu informací vyššími rychlostmi, než jaké nabízejí současné technologie.
Možnosti rozšíření Základní deska je dodávána s následujícími možnostmi rozšíření • Tři 32bitové patice PCI • Jedna patice AGP • Dva konektor IDE podporující až čtyři zařízení IDE • Jedno rozraní pro disketovou mechaniku • Dva 7kolíkové konektor SATA Tato základní deska podporuje řízení sběrnice Ultra DMA s přenosovými rychlostmi 133/100/66 MB/s.
Caracteristici Procesorul Această placă de bază utilizează un soclu 754, având următoarele caracteristici: • Suportă procesoare AMD K8 care utilizează tehnologia HyperTransport Tehnologia HyperTransport este o legătură punct-la-punct între două aparate, care permite viteze mult mai mari de schimb al informaţiilor între circuitele integrate, decât cel asigurat de tehnologiile de interconectare actuale.
Opţiuni de extindere Placa de bază este dotată următoarele posibilităţi de extindere: • Trei sloturi de 32 biţi compatibile PCI • Un slot AGP • Două conectoare IDE care suport cel mult 4 instrumente IDE • O interfaţă pentru unitate floppy • Două conectoare SATA 7 Placa de bază suportă bus mastering UltraDMA cu viteze de transfer de 133/100/66 MB/s Onboard LAN (opţional) Onboard LAN are următoarele caracteristici: • Soluţie cu start fizic cu un singur cip 100Base-TX/10Base-T physical layer solution • Viteză d
Спецификация Процесор Тази дънна платка използва 754-щифтов цокъл (754-pin socket) със следните параметри: • Поддръжка на процесори AMD K8 с технологията HyperTransport Технологията HyperTransport е връзка точка-до-точка (point-to-point) между две устройства, която предоставя възможност интегрираните вериги да обменят информация на много по-висока скорост от досегашно съществуващите технологии.
Възможности за разширяване Дънната платка има следните разширителни възможности: • три слота 32-bit PCI • Един слот AGP • два IDE конектора с поддръжка до четири IDE устройства • един конектор за флопидисково устройство • Два7-щифтови SATA конектораs Дънната платка поддържа шина UltraDMA 133/100/66 MB/s Интегриран мрежов контролер (опция) Спецификация на интегрирания мрежов контролер: • Интегриран едночипов LAN контролер на физическо ниво за Ethernet 100Base-TX/10Base-T • Поддръжка на режими 100/10 Mbps
Jellemző Processzor Ez az alaplap 754 tűs foglalattal rendelkezik, ennek jellemzői pedig a következők: • HyperTransport technológiával rendelkező AMD K8 processzorokkal működik A HyperTransport technológia egy ponttól pontig való kapcsolat két készülék között, és segítségével az integrált áramkörök közötti információcsere sebessége sokkal nagyobb, mint a jelenleg rendelkezésre álló összekapcsolási technológiák esetében.
Bővítési lehetőségek Az alaplap a következő bővítési lehetőségekkel rendelkezik: • Három 32 bites PCI foglalat • Egy AGP foglalat • Két IDE csatlakozó, amely összesen négy IDE eszközt támogat • Egy hajlékonylemez meghajtó interfész • Két 7 tűs SATA csatlakozó Ez az alaplap a UltraDMA bus mastering megoldást, 133/100/66/33 MB/s sebességen Alaplapon levő LAN (választható) Az alaplapon levő LAN jellemzői: • Egylapkás 100Base-TX/10Base-T fizikai réteges megoldás • Duál sebességű 100/10 Mbps • Half /Full Duplex
