Specifications

ManualsBrandsECS ManualsMotherboardsG41T-M2

Preface

This publication, including all photographs, illustrations and software, is protected

any of the material contained herein, may be reproduced without written consent of

the author.

Version 1.0A

Disclaimer

The information in this document is subject to change without notice. The manufac-

turer makes no representations or warranties with respect to the contents hereof and

specifically disclaims any implied warranties of merchantability or fitness for any

particular purpose. The manufacturer reserves the right to revise this publication and

to make changes from time to time in the content hereof without obligation of the

manufacturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel

Corporation.

Other product names used in this manual are the properties of their respective

owners and are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installa-

tion. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause harmful inter-

ference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment onto an outlet on a circuit different from that to

which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Shielded interconnect cables and a shielded AC power cable must be employed with

this equipment to ensure compliance with the pertinent RF emission limits govern-

ing this device. Changes or modifications not expressly approved by the system’s

manufacturer could void the user’s authority to operate the equipment.

Summary of content (66 pages)

PAGE 1
Preface Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. Version 1.0A Disclaimer The information in this document is subject to change without notice.
PAGE 2
ii Declaration of Conformity This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: • • This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation Canadian Department of Communications This class B digital apparatus meets all requirements of the Canadian Interferencecausing Equipment Regulations.
PAGE 3
iii TABLE OF CONTENTS Preface i Chapter 1 1 Introducing the Motherboard 1 Introduction......................................................................................1 Feature...............................................................................................2 Motherboard Components.............................................................5 Chapter 2 7 Installing the Motherboard 7 Safety Precautions............................................................................
PAGE 4
iv PCI/PnP Setup...................................................................37 PC Health Status................................................................37 Frequency/Voltage Control................................................40 Load Default Settings.........................................................41 Supervisor Password.........................................................41 User Password...................................................................42 Save & Exit Setup......
PAGE 5
1 Chapter 1 Introducing the Motherboard Introduction Thank you for choosing the G41T-M2 motherboard. This motherboard is a high performance, enhanced function motherboard designed to support the LGA775 socket Intel® CoreTM 2 Quad/CoreTM 2 Duo/Pentium® Dual-Core/Celeron® processors for high-end business or personal desktop markets. The motherboard incorporates the Intel® G41 Northbridge (NB) and Intel® ICH7 Southbridge (SB) chipsets.
PAGE 6
2 Feature Processor The motherboard uses an LGA775 type of Intel® CoreTM 2 Quad/CoreTM 2 Duo/ Pentium® Dual-Core/Celeron® processors that carries the following features: • Intel® CoreTM 2 Quad/CoreTM 2 Duo/Pentium® Dual-Core/Celeron® processors • Supports a system bus (FSB) of 1333/1066/800 MHz • Supports “Hyper-Threading” technology CPU “Hyper-Threading” technology enables the operating system into thinking it’s hooked up to two processors, allowing two threads to be run in parallel, both on separate “log
PAGE 7
3 Onboard LAN • • • Supports PCI Express™ 1.1 Integrated 10/100/1000 transceiver Wake-On-LAN (WOL) and remote wake-up support Audio (optional) This motherboard may support either of the following Audio chipsets: • • • • 5.1 Channel High Definition Audio Codec ADCs support 44.1k/48k/96kHz sample rate Meets Microsoft WLP 3.10Vista premium and mobile PCs audio requirements TM Direct Sound 3D compatible • • • • • 7.1 channel High Definition Audio Codec All DACs Support 192k/96k/48k/44.
PAGE 8
4 BIOS Firmware This motherboard uses AMI BIOS that enables users to configure many system features including the following: • Power management • Wake-up alarms • CPU parameters • CPU and memory timing The firmware can also be used to set parameters for different processor clock speeds. 1.Some hardware specifications and software items are subject to change without prior notice. 2.Due to chipset limitation, we recommend that motherboard be operated in the ambiance between 0 and 50° C.
PAGE 9
5 Motherboard Components Table of Motherboard Components LABEL COMPONENTS LGA775 socket for Intel® CoreTM 2 Quad/CoreTM 1. CPU Socket 2 Duo/Pentium® Dual-core/Celeron® processors 2. CPU_FAN CPU cooling fan connector 3. DDR2_1~2 240-pin DDR2 SDRAM slots 4. ATX_POWER Standard 24-pin ATX power connector 5. SATA1~4 Serial ATA connectors 6. IDE Primary IDE channel 7. F_PANEL Front panel switch/LED header 8. SYS_FAN System cooling fan connector 9. CLR_CMOS Clear CMOS jumper 10. SPK Speaker header 11.
PAGE 10
6 Memo Introducing the Motherboard
PAGE 11
7 Chapter 2 Installing the Motherboard Safety Precautions • • • • • Follow these safety precautions when installing the motherboard Wear a grounding strap attached to a grounded device to avoid damage from static electricity Discharge static electricity by touching the metal case of a safely grounded object before working on the motherboard Leave components in the static-proof bags they came in Hold all circuit boards by the edges.
PAGE 12
8 Do not over-tighten the screws as this can stress the motherboard. Checking Jumper Settings This section explains how to set jumpers for correct configuration of the motherboard. Setting Jumpers Use the motherboard jumpers to set system configuration options. Jumpers with more than one pin are numbered. When setting the jumpers, ensure that the jumper caps are placed on the correct pins. The illustrations show a 2-pin jumper. When the jumper cap is placed on both pins, the jumper is SHORT.
PAGE 13
9 Checking Jumper Settings The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled. Jumper Settings Jumper Type Description Setting (default) 1-2: NORMAL CLR_CMOS 3-pin USBPWR_F 3-pin USBPWR_R 3-pin Clear CMOS 2-3: CLEAR Before clearing the CMOS, make sure to turn off the system. Front Panel USB Power Select Jumper 1-2: VCC 2-3: 5VSB Rear USB PS/2 Power Select Jumper 1-2: VCC 2-3: 5VSB 1 CLR_CMOS 1 USBPWR_F 1 USBPWR_R 1.
PAGE 14
10 Installing Hardware Installing the Processor Caution: When installing a CPU heatsink and cooling fan make sure that you DO NOT scratch the motherboard or any of the surfacemount resistors with the clip of the cooling fan. If the clip of the cooling fan scrapes across the motherboard, you may cause serious damage to the motherboard or its components. On most motherboards, there are small surface-mount resistors near the processor socket, which may be damaged if the cooling fan is carelessly installed.
PAGE 15
11 CPU Installation Procedure The following illustration shows CPU installation components. A. Read and follow the instructions shown on the sticker on the CPU cap. B. Unload the cap · Use thumb & forefinger to hold the lifting tab of the cap. · Lift the cap up and remove the cap completely from the socket. C. Open the load plate · Use thumb & forefinger to hold the hook of the lever, pushing down and pulling aside unlock it. · Lift up the lever. · Use thumb to open the load plate.
PAGE 16
12 Installing Memory Modules This motherboard accommodates two memory modules. It can support two 240-pin DDR2 800/667. The total memory capacity is 8 GB. DDR2 SDRAM memory module table Memory module DDR2 667 DDR2 800 Memory Bus 333 MHz 400 MHz You must install at least one module in any of the two slots. The total memory capacity is up to 8 GB. Do not remove any memory module from its antistatic packaging until you are ready to install it on the motherboard. Handle the modules only by their edges.
PAGE 17
13 Table A: DDR2 (memory module) QVL (Qualified Vendor List) The following DDR2 800/667 memory modules have been tested and qualified for use with this motherboard. Type Size 512 MB Vendor 78.91G92.9K5 Micron MT4HTF6464AY-667E1 PSC AL6E8E63J-6E1 Ramxel RML1520M38D6F-667 Samsung PC2-5300U-555-12-D3 Apacer 1 GB Module Nam e Apacer AU01GE667C5KBGC 78.01G9O.
PAGE 18
14 Type Size 512 MB Vendor Module Nam e Kingston KVR800D2N5/512 1.8V 9905315019.A02LF Micron MT8HTF6464AY-80ED4 Qimonda HYS72T64000HU-2.5-B A-DATA Aeneon M2GVD6G3I41P0U1E5E AET760UD00-30DB97X AET760UD00-25DC08X AU01GE800C5KBGC Apacer 78.01GAO.9K5 78.01GA0.9L5 Geil DDR2 800 1 GB Geil Millenary Hexon ELPT7AUDR-25M48 Hynix HYMP112U64CP8-S6 AB KingMax KLDD48F-B8KU5 NGES Kingston KVR800D2N5/1G 1.8V 9905316054.
PAGE 19
15 Type Size Vendor Module Nam e A-DATA Red A-data M2OMI6H3J4720L1C5Z Aeneon AET860UD00-25DC08X Apacer CM2X2048-6400C5 Geil Geil Platinum Edition Hexon ELPT8AUDR-25M88 Hynix HYMP125U64CP8-S6 AB KingMax KLDE88F-B8KU5 NHES Kingston KVR800D2N5/2G KVR800D2N6/2G-SP Micron MT16HTF25664AY-800E1 Nanya NT2GT64U8HD0BY-AD PSC AL8E8F73C-8E1 Qimonda HYS64T256020EU-25F-C2 Samsung 4 GB 78.A1GC0.9L4 CORSAIR 2 GB DDR2 800 78.A1GAO.
PAGE 20
16 Expansion Slots Installing Add-on Cards The slots on this motherboard are designed to hold expansion cards and connect them to the system bus. Expansion slots are a means of adding or enhancing the motherboard’s features and capabilities. With these efficient facilities, you can increase the motherboard’s capabilities by adding hardware that performs tasks that are not part of the basic system.
PAGE 21
17 Follow these instructions to install an add-on card: 1 2 3 Remove a blanking plate from the system case corresponding to the slot you are going to use. Install the edge connector of the add-on card into the expansion slot. Ensure that the edge connector is correctly seated in the slot. Secure the metal bracket of the card to the system case with a screw. 1.
PAGE 22
18 Connecting Optional Devices Refer to the following for information on connecting the motherboard’s optional devices: SATA1~4: Serial ATA connectors These connectors are used to support the new Serial ATA devices for the highest data transfer rates (3.0 Gb/s), simpler disk drive cabling and easier PC assembly. It eliminates limitations of the current Parallel ATA interface. But maintains register compatibility and software compatibility with Parallel ATA.
PAGE 23
19 F_USB1~2: Front Panel USB headers The motherboard has four USB ports installed on the rear edge I/O port array. Additionally, some computer cases have USB ports at the front of the case. If you have this kind of case, use auxiliary USB connector to connect the front-mounted ports to the motherboard.
PAGE 24
20 COM: Onboard serial port header Connect a serial port extension bracket to this header to add a second serial port to your system.
PAGE 25
21 About SATA Connectors Your motherboard features four SATA connectors supporting a total of four drives. SATA refers to Serial ATA (Advanced Technology Attachment) is the standard interface for the IDE hard drives which are currently used in most PCs. These connectors are well designed and will only fit in one orientation. Locate the SATA connectors on the motherboard and follow the illustration below to install the SATA hard drives.
PAGE 26
22 Connecting I/O Devices The backplane of the motherboard has the following I/O ports: PS2 Mouse Use the upper PS/2 port to connect a PS/2 pointing device. PS2 Keyboard Use the lower PS/2 port to connect a PS/2 keyboard. DVI Port Use the DVI port to connect the monitor. Parallel Port (LPT) Use LPT to connect printers or other parallel communica tions devices. VGA Port Connect your monitor to the VGA port. LAN Port Connect an RJ-45 jack to the LAN port to connect your computer to the Network.
PAGE 27
23 Connecting Case Components After you have installed the motherboard into a case, you can begin connecting the motherboard components. Refer to the following: 1 2 3 4 5 6 Connect the CPU cooling fan cable to CPU_FAN. Connect the standard power supply connector to ATX_POWER. Connect the case switches and indicator LEDs to the F_PANEL. Connect the system cooling fan connector to SYS_FAN. Connect the case speaker cable to SPK. Connect the auxiliary case power supply connector to ATX12V.
PAGE 28
24 CPU_FAN: CPU Cooling FAN Power Connector Pin 1 2 3 4 Signal Name Function GND System Ground +12V Power +12V Sense Sensor PWM PWM Users please note that the fan connector supports the CPU cooling fan of 1.1A ~ 2.2A (26.4W max) at +12V. ATX_POWER: ATX 24-pin Power Connector Pin 1 2 3 4 5 6 7 8 9 Signal Name Pin Signal Name 13 14 15 16 17 18 19 20 21 +3.3V +3.3V Ground +5V Ground +5V Ground PWRGD +5VSB +3.
PAGE 29
25 ATX12V: ATX 12V Power Connector Pin 1 2 3 4 Signal Name Ground Ground +12V +12V Installing the Motherboard
PAGE 30
26 Front Panel Header The front panel header (F_PANEL) provides a standard set of switch and LED headers commonly found on ATX or micro-ATX cases.
PAGE 31
27 Chapter 3 Using BIOS About the Setup Utility The computer uses the latest “American Megatrends Inc. ” BIOS with support for Windows Plug and Play. The CMOS chip on the motherboard contains the ROM setup instructions for configuring the motherboard BIOS. The BIOS (Basic Input and Output System) Setup Utility displays the system’s configuration status and provides you with options to set system parameters.
PAGE 32
28 Press the delete key to access the BIOS Setup Utility. CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc.
PAGE 33
29 For the purpose of better product maintenance, we reserve the right to change the BIOS items presented in the manual. The BIOS setup screens shown in this chapter are for reference only. Please visit our website for updated manual. Standard CMOS Setup This option displays basic information about your system. CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc.
PAGE 34
30 f Primary IDE Master/Slave; SATA1~4 Your computer has one IDE channel and each channel can be installed with one or two devices (Master and Slave). In addition, this motherboard supports four SATA channels and each channel allows one SATA device to be installed. Use these items to configure each device on the SATA channel. CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc.
PAGE 35
31 Advanced Setup This page sets up more advanced information about your system. Handle this page with caution. Any changes can affect the operation of your computer. CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc.
PAGE 36
32 Boot Up Numlock Status (On) This item defines if the keyboard Num Lock key is active when your system is started. APIC Mode (Enabled) This item allows you to enable or disable the APIC (Advanced Programmable Interrupt Controller) mode. APIC provides symmetric multi-processing (SMP) for systems, allowing support for up to 60 processors. 1st/2nd/3rd Boot Device (Hard Disk Drive/CD/DVD/Removable Dev.
PAGE 37
33 Advanced Chipset Setup This page sets up more advanced information about your system. Handle this page with caution. Any changes can affect the operation of your computer. CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc.
PAGE 38
34 Integrated Peripherals This page sets up some parameters for peripheral devices connected to the system. CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc.
PAGE 39
35 Parallel Port IRQ (IRQ7) Use this item to assign IRQ to the parallel port. USB Functions (Enabled) Use this item to enable or disable the USB function. Legacy USB Support (Enabled) Use this item to enable or disable support for legacy USB devices. Press to return to the main menu setting page. Power Management Setup This page sets up some parameters for system power management operation. CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc.
PAGE 40
36 Resume By RING (Disabled) An input signal on the serial Ring Indicator (RI) line (in other words, an incoming call on the modem) awakens the system from a soft off state. Resume By PCI/PCI-E/Lan PME (Disabled) These items specify whether the system will be awakened from power saving modes when activity or input signal of the specified hardware peripheral or component is detected. Resume By USB (S3) (Disabled) This item allows you to enable/disable the USB device wakeup function from S3/S4 mode.
PAGE 41
37 PCI/PnP Setup This page sets up some parameters for devices installed on the PCI bus and those utilizing the system plug and play capability. CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. PCI/PnP Setup Init Display First PCI Help Item Select which graphics controller to use as the primary boot device.
PAGE 42
38 f Smart Fan Function (Press Enter) Scroll to this item and press to view the following screen: CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. Smart Fan Function SMART Fan Control Disabled Help Item Options Disabled Enabled mnlk : Move Enter : Select F1: General Help +/-/: Value F10: Save ESC: Exit F9: Load Default Settings SMART Fan Control (Disabled) This item allows you to enable/disable the control of the CPU fan speed by changing the fan voltage.
PAGE 43
39 ECS supports the latest PECI host technology. While using CoreTM 2 Quad or CoreTM 2 Duo CPU which supports PECI, the original images of the BIOS item “PC Health Status” and “Smart FAN Function” will be replaced by PECI mode and negative number. (The max data from PECI is zero.) CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. PC Health Status Help Item -=- System Hardware Monitor-=Press Enter CPU Fan Speed : 2509 RPM CPU Vcore : 1.088 V VDIMM : 1.
PAGE 44
40 Shutdown Temperature (Disabled) Enable you to set the maximum temperature the system can reach before powering down. System Component Characteristics These items display the monitoring of the overall inboard hardware health events, such as System & CPU temperature, CPU & DIMM voltage, CPU & system fan speed,...etc.
PAGE 45
41 Auto Detect DIMM/PCI Clk (Enabled) When this item is enabled, BIOS will disable the clock signal of free DIMM/PCI slots. Spread Spectrum (Enabled) If you enable spread spectrum, it can significantly reduce the EMI (Electro-Magnetic Interference) generated by the system. Press to return to the main menu setting page. Load Default Settings This option opens a dialog box that lets you install stability-oriented defaults for all appropriate items in the Setup Utility.
PAGE 46
42 User Password This page helps you install or change a password. CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. User Password User Password : Not Installed mnlk : Move Enter : Select F1: General Help Help Item +/-/: Value F10: Save ESC: Exit F9: Load Default Settings User Password (Not Installed) This item indicates whether a user password has been set. If the password has been installed, Installed displays. If not, Not Installed displays.
PAGE 47
43 Updating the BIOS You can download and install updated BIOS for this motherboard from the manufacturer’s Web site. New BIOS provides support for new peripherals, improvements in performance, or fixes for known bugs. Install new BIOS as follows: 1 If your motherboard has a BIOS protection jumper, change the setting to allow BIOS flashing. 2 If your motherboard has an item called Firmware Write Protect in Advanced BIOS features, disable it. (Firmware Write Protect prevents BIOS from being overwritten.
PAGE 48
44 Memo Using BIOS
PAGE 49
45 Chapter 4 Using the Motherboard Software About the Software CD-ROM The support software CD-ROM that is included in the motherboard package contains all the drivers and utility programs needed to properly run the bundled products. Below you can find a brief description of each software program, and the location for your motherboard version. More information on some programs is available in a README file, located in the same directory as the software.
PAGE 50
46 Setup Tab Setup Click the Setup button to run the software installation program. Select from the menu which software you want to install. Browse CD The Browse CD button is the standard Windows command that allows you to open Windows Explorer and show the contents of the support CD. Before installing the software from Windows Explorer, look for a file named README.TXT, INSTALL.TXT or something similar. This file may contain important information to help you install the software correctly.
PAGE 51
47 2. Click Next. The following screen appears: 3. Check the box next to the items you want to install. The default options are recommended. 4. Click Next run the Installation Wizard. An item installation screen appears: 5. Follow the instructions on the screen to install the items. 1. Drivers and software are automatically installed in sequence. Follow the onscreen instructions, confirm commands and allow the computer to restart a few times to complete the installation. 2.
PAGE 52
48 Method 1. Run Reboot Setup Windows Vista will block startup programs by default when installing drivers after the system restart. You must select taskbar icon Run Blocked Program and run Reboot Setup to install the next driver, until you finish all drivers installation. Method 2. Disable UAC (User Account Control) * For administrator account only. Standard user account can only use Method 1.
PAGE 53
49 2. Select Classic View. 3. Set User Account. 4. Select Turn User Account Control on or off and press Continue.
PAGE 54
50 5. Disable User Account Control (UAC) to help protect your computer item and press OK, then press Restart Now. Then you can restart your computer and continue to install drivers without running blocked programs. Manual Installation Insert the CD in the CD-ROM drive and locate the PATH.DOC file in the root directory. This file contains the information needed to locate the drivers for your motherboard.
PAGE 55
51 Chapter 5 Setting Up eJIFFY Introduction eJIFFY is a fast boot program under Linux. Instead of waiting Windows O.S to start execution, eJIFFY is ready to provide users the instant enjoyment on web browsing, photo review and online chat just within several seconds after boot up. Version: 1.
PAGE 56
52 Installation and BIOS Setup You need to finish the CD installation first before setting the BIOS. 1. Insert the eJIFFY CD in the CD-ROM drive. And follow the onscreen instructions to finish the OS installation. 2. Enter My Computer to find the eJIFFY setup program. 3. Click the setup button to run the eJIFFY software installation program, restart your computer after you finish.
PAGE 57
53 4. Press or click the BIOS Setup button on the post screen to enter the BIOS setup page after boot up. 5. And then enter the Advanced Setup page to enable the item ECS eJIFFY Function. Press F10 to save the configuration and exit. Restart your computer. Note: 1. eJIFFY is available in SATA/IDE/AHCI mode. It does not support RAID configuration and the onboard 34-pin floppy drives. 2. Please refer to ECS website for new eJIFFY application updates.
PAGE 58
54 Entering eJIFFY The post screen appears within several seconds after boot up and it has three buttons on it, Operating system, eJIFFY and BIOS Setup. Click to enter the normal OS you have installed such as Windows. Click to enter eJIFFY OS. Click to set the BIOS. If you click eJIFFY, the following screen will appear. And if you make no choice it will enter the normal OS automatically after ten seconds.
PAGE 59
55 Feature Icons The following illustration shows the main feature icons that eJIFFY provides on the menu. eWeb: Firefox for web browsing/webmail and watching flash video. ePix: Photo viewing. ePal: On-line chat tool to use the most popular IMs in the world. (MSN, ICQ , AIM, etc.) Shows ePal on-line connection status. Shut Down/Restart: Ends your session and turns off the computer./Ends your session and restart the computer.. Click once to connect the storage disk to your computer.
PAGE 60
56 Usage FAQ eWeb: Firefox for web browsing/webmail and watching flash video. Q1: How to download files to hard disk through eWeb? Click on the file link directly. Then select “Save File” in the pop-up window. Note: 1. Before downloading files, please “mount” the storage devices to make sure the device is connected with eJIFFY interface. (Please refer to the usage FAQ to mount devices) 2. eWeb does not support Office Viewer/Reader/Writer format under eJIFFY interface.
PAGE 61
57 Q2: How to switch to different languages settings? Step1. Step2.
PAGE 62
58 Q3: How to save image file through eWeb? 1. Select the image you want to save and press the right key of your mouse to show the menu, then click the option “ Save Image As” from the menu. 2. Then the “Save Image” window appears. You may rename the image file in the “Name” column and save the file in a folder as the following picture shows. Rename the image file. Then select a subdirectory or click “Create Folder” to create a new folder. Select a root directory. Click here to save the image file.
PAGE 63
59 ePix: Photo viewing. Q1: How to find image files saved in hard disk through ePix? Enter the ePix window, then click the icon “Folder” located in the upper left-hand corner, then follow the path for the files you have saved to view the image files.
PAGE 64
60 Q2: How to use the fit function under slide show? 1. Click “Edit” and select “Preferences” option from the menu. 2. Click “Viewer” and choose “Keep previous zoom” in “After loading an image”. Close the window and you can use the fit function under slide show now. Note: ePix supports to view image files only. It cannot support Office Viewer or other forms beside image files. Supported image types are: BMP, JPEG, GIF (including GIF animations), PNG, TIFF, ICO and XPM.
PAGE 65
61 Mount/Unmount Disk. Q1: What does it mean for “Mount Disk”? “Mount” means to connect the storage devices to eJIFFY interface. After plugging the external device to the computer such as USB drives, a new disk icon will appear as the following picture shows. Please click the “mount” prompt on the icon. It will change to to show the device is detected successfully. Q2: What does it mean for “Unmount Disk”? “Unmount” is to safely remove the storage devices.
PAGE 66
62 Memo Setting Up eJIFFY