Instruction Manual
Important Safety Instructions When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE. SAVE THESE INSTRUCTIONS 1. This appliance can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
to the glass or has visible signs of damage. 14. To reduce the risk of electrical shock, do not put the Appliance in water or other liquid. Do not place or store Appliance where it can fall or be pulled into a tub or sink. 15. Do not touch power plug or the Appliance with wet hands. 16. Do not charge the Appliance in extremely hot or cold environments, or it may affect battery life span. 17. When charging the Appliance, do not place it on other electrical appliances and keep it away from fire and liquid.
29. The robot contains batteries that are only replaceable by skilled persons. 30. The plug and the Power Adapter must be used indoor. To satisfy RF exposure requirements, a separation distance of 20 cm or more should be maintained between this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. The antenna used for this transmitter must not be co-located in conjunction with any other antenna or transmitter.
Package Contents Product Diagram WINBOT Status Indicator Light/START/ PAUSE Button WINBOT+ Safety Tether and Carabiner Power Adapter Bumper Rail Instruction Manual Bottom View Instruction Manual Finishing Cloth Edge Detection Sensors Side Rollers Power Switch Driving Treads WINBOT Cleaning Solution Cleaning Pads Note: Figures and illustrations are for reference only and may differ from actual product appearance. Product design and specifications are subject to change without notice.
Notes Before Cleaning Make sure Safety Tether and Carabiner have been connected with WINBOT before using. (Connected by default. Do not disconnect before cleaning.) Note: Do not use WINBOT on a framed window with a frame narrower than 5 mm(0.2”).
Quick Start 1 Connect WINBOT Power Cord, Power Adapter and Plug A 2 B C 3 ECOVACS HOME App To enjoy all available features, it is recommended to control your WINBOT via the ECOVACS HOME App. • Deep Cleaning Mode • Spot Cleaning Mode • Switching Interior/Exterior Window Preparation before Use Properly Tether WINBOT to a Safe Place ECOVACS HOME Note: To ensure safety, please make sure to properly tether WINBOT to a safe place before use.
Spray Cleaning Solution It is recommended to use WINBOT with WINBOT Cleaning Solution from ECOVACS. Using tap water or other cleaners could have an adverse effect on cleaning performance. Using other cleaning solutions could potentially void the warranty. Note: Do not over-spray Cleaning Solution as doing so may cause the driving treads to slip. Wipe the Bottom of WINBOT with a Dry Cloth Wipe the Area for WINBOT to Attach to Wipe the area for WINBOT to safety attach to.
5 Pause Power Off Unfasten Safety Tether 1 6 2 Finish Remove WINBOT Unplug WINBOT 9 EN
Maintenance Cleaning Pad Replace the Cleaning Pad Remove the dirty Cleaning Pad from the WINBOT and place a clean new one on it. Please make sure the cleaning pad is correctly attached, and do not cover the Edge Detection Sensors. A B B A A>B Note: The gray microfiber side faces out. Washing Cleaning Pad Note: Wash with mild detergent. Do NOT use a wet Cleaning Pad on WINBOT or it may slip on the window. Washing the Cleaning Pad regularly can extend its service life.
Driving Treads 1 2 3 Note: Inspect the Driving Treads in ECOVACS HOME App. Stop the Driving Treads if you see dirt on them. Fan Edge Detection Sensors Side Rollers * After WINBOT has a low battery alarm, be sure to fully charge it before using or storing it to avoid reducing the battery life. * If WINBOT will not be used for a long time, please fully charge it and turn it off before storage. Recharge it every six months to prevent the battery from being over-discharged.
Status Indicator Light Light Effect Status WINBOT is fully charged. WINBOT has successfully adhered itself to the glass and is ready to clean. Status Indicator glows a continuous BLUE. WINBOT is cleaning. WINBOT is paused. The network setup is complete. Status Indicator flashes BLUE slowly. WINBOT is paused and charging. WINBOT is in sleep mode. Press to wake it up. Status Indicator stops glowing BLUE. WINBOT is powered OFF. EN Status Indicator glows a continuous RED. WINBOT has a low battery.
Troubleshooting NO. Malfunction Possible Causes There is too much dirt and debris on the glass. The Cleaning Pad is too dirty. 1 WINBOT moves in an irregular pattern during cleaning. The Cleaning Pad is too wet. The Driving Treads are dirty. 2 WINBOT does not move. WINBOT cannot move or moves in circles. A. Spray additional Cleaning Solution on the Cleaning Pad. B. Clean the Driving Treads as described in section 3. C. Replace the Cleaning Pad and restart the cleaning cycle. D.
NO. Malfunction Possible Causes The bumper rail is stuck. The bumper rail is damaged. 4 5 6 EN 14 WINBOT is stays still or moves in an irregular pattern during cleaning. WINBOT stops moving after adhering to the glass. WINBOT is stuck. Solutions Remove WINBOT from the window. Check if the bumper rail is stuck. Clean the bumper rail and restart WINBOT. If problem persists, please contact customer service. Edge Detection Sensor signal abnormity. A.
App Connection Before connection, make sure WINBOT and the mobile phone meet the following requirements: 1. The Bluetooth of the mobile phone is turned on. 2. The WINBOT power switch has been turned on and the indicator light has been lit. 3. Please pair WINBOT in ECOVACS HOME App instead of the phone setting. 4. Co-frequency interference might occur between Bluetooth and Wi-Fi. It is recommended to keep WINBOT close to the mobile phone and distant from the Wi-Fi router during pairing. 5.
Ecovacs Home Service Robotics Co., Ltd. No. 518 Songwei Road, Wusongjiang industry Park, Guoxiang Street, Wuzhong District, Suzhou, Jiangsu, China.
