EN Instruction Manual
Congratulations on the purchase of your ECOVACS Robotics DEEBOT! We hope it brings you many years of satisfaction. We trust the purchase of your new robot will help keep your home clean and provide you more quality time to do other things. Live Smart. Enjoy Life. Should you encounter situations that have not been properly addressed in this Instruction Manual, please contact our Customer Service Center where a technician can address your specific problem or question.
Contents 1. Important Safety Instructions....................................................................... 2 2. Package Contents and Technical Specifications....................................... 4 2.1 Package Contents..................................................................................... 4 2.2 Specifications............................................................................................ 4 2.3 Product Diagram...................................................................
1. Important Safety Instructions When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE. SAVE THESE INSTRUCTIONS 1. This Appliance is not intended to be used by children under 8 or anyone lacking knowledge on proper use. Supervision may be necessary. Do not allow children to sit on or play with the Appliance. 2. Clear the area to be cleaned.
1. Important Safety Instructions 23. Do not use with a damaged power cord or receptacle. Do not use the Appliance or Charging Dock if it is not working properly, has been dropped, damaged, left outdoors, or come in contact with water. It must be repaired by the manufacturer or its service agent in order to avoid a hazard. 24. Please clean and maintain the Appliance as described in the maintenance section of this instruction manual. 25. Turn OFF the power switch before cleaning or maintaining the Appliance.
2. Package Contents and Technical Specifications 2.1 Package Contents EN Instruction Manual Robot Charging Dock Remote Control (with Batteries) Instruction Manual (4) Side Brushes Battery Pack (with 2 screws) (2) Smart Clean Cloths Smart Clean Reservoir Direct Suction Option Main Brush Option (pre-installed) Measuring Cup 2.2 Specifications Model Working Voltage DM85 14.
2. Package Contents and Technical Specifications 2.3 Product Diagram Robot 1 4 2 5 6 13 14 9 10 7 8 11 3 12 1. Top Cover 2. Control Panel 3. Anti-Collision Sensors 4. Anti-Drop Sensors 5. Charging Contacts 6. Side Brushes 7. Main Brush Option 8. Driving Wheels 9. Universal Wheel 10. Battery Pack with Screws 11. Smart Clean Reservoir Slots 12. Infrared Receiver for Remote Control 13. Dust Sensors 14. Dust Bin Control Panel 2 1 4 3 5 1. Spot Cleaning Mode Button 2. Edge Cleaning Mode Button 3.
2. Package Contents and Technical Specifications Remote Control 12 1 2 3 4 5 11 10 9 6 7 1. LCD Screen 2. Return to Charger Mode Button 3. AUTO Mode Button 4. Direction Control Buttons 5. START/PAUSE Button 6. Spot Cleaning Mode Button 7. Edge Cleaning Mode Button 8. Intensive Cleaning Mode Button 9. Set Current Time Button 10. Time Scheduling Button 11. Second Time Scheduling Button 12. Infrared Emitter 8 Dust Bin 1 2 3 4 1. Dust Bin Handle 2. Dust Bin Lock 3. Dust Bin Cover 4.
3. Operating and Programming 3.1 Notes before Cleaning Before operating DEEBOT, take a few moments to survey the area to be cleaned and remove any obstacles. Remove power cords and small objects from the floor that could entangle the product. The product is not suitable for use on long-pile carpet. Before using the product near an area rug or on a short-pile area rug with tasseled edges, please fold area rug edges under themselves.
3. Operating and Programming 3.2 Quick Start 1 Charging Dock Placement Place the Charging Dock on a level floor surface against the wall with the base perpendicular to the ground. Keep the immediate area 1.5m (5’) in front of the charger and 0.5m (1.6’) on both sides of the charger clear of objects and reflective surfaces. Plug the Charging Dock in. 2 Install Battery Insert the Battery Pack into the battery slot on the bottom of DM85. Insert and tighten the screws with a coin to secure the Battery Pack.
3. Operating and Programming 4 Power ON Press and hold the button on the robot for 3 seconds. DM85 is powered ON when the button illuminates. Ő3Ƞ ON 5 Charge DM85 Remove the Smart Clean Reservoir before charging DM85. Place DM85 on the Charging Dock making sure the Charging Contacts on DM85 and the Charging Dock Pins make a connection. Charge DM85 for at least 12 hours before the first use. button blinks when DM85 is charging and stays on when DM85 is fully charged.
3. Operating and Programming 7 Start Press the AUTO Mode Button on DM85’s Control Panel or the AUTO Mode Button on the Remote Control. DM85 starts to work immediately in AUTO Cleaning Mode. * To choose another Cleaning Mode, please refer to section 3.3 Cleaning Mode Selection for details. 8 Pause Pause DM85 by pressing the AUTO Mode Button on the robot’s Control Panel or the START/PAUSE Button on the Remote Control.
3. Operating and Programming 3.3 Cleaning Mode Selection DM85 has several Cleaning Modes for you to choose from to effectively clean different floors. Cleaning Modes are selected using the robot’s Control Panel Buttons or using the Remote Control. * To switch Cleaning Modes using the robot’s Control Panel Buttons, Pause DM85 first, and then press the desired Cleaning Mode Button on the Control Panel. * To switch Cleaning Modes using the Remote Control, press the desired Cleaning Mode Button.
3. Operating and Programming 3 Spot Cleaning Mode (1 Minute) This mode is applicable for an area of highly concentrated dirt or dust. In Spot Cleaning Mode, DM85 focuses on a specific area to clean. 4 Edge Cleaning Mode This mode is good for cleaning the edges and corners of a room. In Edge Cleaning Mode, DM85 cleans along a border (e.g. wall). 5 Return to Charger Mode When battery power gets low, DM85 automatically switches to Return to Charger Mode and returns to the Charging Dock to recharge itself.
3. Operating and Programming 3.4 Programming the Robot DM85 has a Time Scheduling function. DM85 can be programmed to automatically clean once or twice per day, at specific times, even if nobody is at home. The current time of day and the cleaning times are scheduled using the Remote Control. * All scheduled cleanings are performed in AUTO Cleaning Mode. * The Remote Control uses a 12-hour clock with “AM” and “PM” indicators.
3. Operating and Programming Schedule the Cleaning Time Press button on the Remote Control until flashes and illuminates on the Remote Control LED Screen. Press the up and down Direction Control Buttons to adjust “hour” and “minute” number. Press the left and right Direction Control Buttons to switch between hour, minute and AM/PM. button on the Remote Control to Press confirm and save the scheduled cleaning time. DM85 can be scheduled to clean twice per day, at two different times.
3. Operating and Programming Cancel Scheduled Cleaning Time To cancel the first cleaning time, press and hold button until disappears from the Remote Control LED Screen. The scheduled cleaning time is cancelled. To cancel the second cleaning time, press and hold button until disappears from the Remote Control LED Screen. The second scheduled cleaning time is cancelled. Ő3Ƞ Ő3Ƞ 3.
3. Operating and Programming 2 Attach Smart Clean Cloth Attach the Smart Clean Cloth to the Smart Clean Reservoir. Attach the Smart Clean Reservoir to the bottom of the robot. Insert the tabs on the Smart Clean Reservoir into the Smart Clean Reservoir Slots on the bottom of the robot until you hear a click. 3 Start Select the desired Cleaning Mode. DM85 sweeps and mops in the selected mode.
3. Operating and Programming 3.6 Choosing a Suction Option DM85 has 2 interchangeable suction options for your convenience. Main Brush Option: The best choice for deep cleaning with a combination of the Main Brush and strong suction. The Main Brush Option comes pre-installed in DM85. Direct Suction Option: The best choice for daily cleaning with the Main Brush removed for direct suction. This Suction Option is specifically designed to pick up hair without tangling.
3. Operating and Programming 3.7 Alarm Indicator and Sounds If the robot detects a problem, it emits an alarm sound and the AUTO Mode Button flashes RED. Please troubleshoot according to the alarm sounds. Alarm Sound Problems Solution One Beep Driving Wheel Malfunction Check Driving Wheels for tangled hair or debris and clean. Two Beeps Main Brush Malfunction Check Main Brush for tangled hair or debris and clean. Three Beeps Driving Wheel Malfunction Turn over the robot.
4. Maintenance Before performing cleaning and maintenance on DM85, power OFF the robot and unplug the Charging Dock. 4.1 Dust Bin and Filters Cleaning the Dust Bin and the Filters Open DM85’s Top Cover and remove the Dust Bin. Open the Dust Bin Cover and empty the Dust Bin. Remove the filters. Pat the High Efficiency Filter clean. Do not rinse the High Efficiency Filter under water. Wash and Dry Rinse the Dust Bin and Filter Net under running water.
4. Maintenance 4.2 Smart Clean Cloth, Smart Clean Reservoir Cleaning the Smart Clean Cloth If the mopping system was used, remove the Smart Clean Reservoir from the bottom of DM85 and remove the Cleaning Cloth. Empty any remaining water from the Water Reservoir. Wash the Smart Clean Cloth by hand or in the washing machine, and lay flat to dry. Cleaning the Smart Clean Reservoir If the mopping system was used, remove the Smart Clean Reservoir from the bottom of DM85.
4. Maintenance 4.3 Main Brush, Direct Suction Option and Side Brushes A Multi-Function Cleaning Tool is provided for easy maintenance. Handle with care, this cleaning tool has sharp edges. Cleaning the Main Brush Turn the robot over. Push both buttons on the Main Brush Option towards the center of the robot. Remove the Main Brush Cover. Remove the Main Brush. Use the Multi-Function Cleaning Tool to cut off and remove any hair tangled around the Main Brush.
4. Maintenance 4.4 Other Components Use the Multi-Function Cleaning Tool to cut off and remove any hair tangled around the Universal Wheel. Wipe the Anti-Drop Sensors with the brush or the felt side of the Multi-Function Cleaning Tool to maintain their effectiveness. Wipe the Dust Sensors with the brush or the felt side of the Multi-Function Cleaning Tool to maintain their effectiveness.
5. Troubleshooting Please use this chart to troubleshoot common problems using DM85. No. 1 2 3 4 Malfunction DM85 will not charge. DM85 gets into trouble while working and stops. DM85 returns to the Charging Dock before it finishes cleaning. DM85 will not clean automatically at scheduled time. Possible Causes Solutions DM85 is not powered ON. Press and hold AUTO Mode Button on DM85 to power ON. DM85 has not made a connection with the Charging Dock.
5. Troubleshooting No. 5 24 EN Malfunction Remote Control failure (effective control range of Remote Control is 5m (16’)). Possible Causes Solutions The batteries in the Remote Control need to be replaced. Replace with new batteries making sure they are installed correctly. DM85 is powered OFF or DM85’s battery is low. Make sure DM85 is powered ON and fully charged.
DM85-000-IM2014R01
