Robot Vacuum Cleaner 7 Series User Guide
Thanks for purchasing patented Robot Vacuum Cleaner products.
7Series special function ● Automatic detecting stairs and changing walking route to avoid falling off; ● Automatic reducing speed when detecting obstacles within 6cm ahead to avoid bumping into furniture and the wall and causing breakage; ● Dual side brush design to make more efficient clean; ● Unique voicing and dancing function – you can log in official website to update at www.ecovacs.
Enjoy Smarter Life! Content This User Guide is for all Deepoo 7Series products 1. Safety Instruction........................................ 3 Set Appointment Time...................................... 15 User Guide......................................................... 3 Set Current Time.............................................. 16 Power Supply for the Product............................ 3 Set Frequency and Cancel Timing................... 17 The Spectrum of Product Use........................
1.Safety Instruction Note： Do not open the equipment. The components inside the robot host are beyond repair by user himself, such as remote control and virtual wall. This product is only for domestic use, not suitable for industry or outdoor surroundings. Please do not press LCD. Please follows the instruction of the host and the user manual to insert the SD card. If you insert the card in the wrong direction and cause destroy of the product, we cannot offer the maintenance service.
Enjoy Smarter Life! The Spectrum of the Product Use 瓷砖 短毛 地毯 ● This robot is applicable to domestic sweeping, including wooden floor, rubber floor, ceramic tile, linoleum and medium or short-haired carpet however, it is inapplicable to long-haired carpet. ● It can not be used for the floor as below: 地板 ---- Have water on the surface (including flammable liquids), such as wet floor. ---- Inside toilet, shower room or other humid situation.
Notes before Cleaning ● Take extra care of the robot when the first it works. Please remove the obstacles when it is beyond the robot. Try to avoid the situation that the robot stops working. ● Make precautions to solve the problem which may make the cleaning in trouble, such as: ---- Keep the easily knock over objects in a safe place. ---- Permian the edge of the carpet. ---- The hanging table cloth and curtain should not touch the ground. ---- The flammable object should be cut from the fire source.
Enjoy Smarter Life! ● Take good care of the product and keep it beyond child and people who can not judge danger nearby. Extra attention should be paid when it starts working. ● You should get the person inside the room know that the machine is working, in order to avoid man-made damage like tripping. ● Do not take robot as toy. Carefully attention should be paid when child or pet is around. ● The plastic package may bring danger of asphyxia keep away from child.
2.
Enjoy Smarter Life! technique parameter The host Working voltage Rated power Speed The charging block In-put voltage DC12V rated out-put voltage 30W Noise 50Hz 0.7L rated power 30W ≤62dB rated out-put currency 1.0A Charging duration About 3 hours Duration upon full battery 60 minutes About 60 minutes Max Coverage upon full battery 120-150M Size Net weight Vir tual wall In-put voltage DC3V Remote control 2 330×330×97.5mm 3.
2.Content(For D76) Robot Vacuum Cleaner 7 Se ri es U se r Gu id e Main Unit User Guide Charge Station Telescopic tube Magnetism recovery tool Remote control battery Hose 2 in 1 brush 娱乐 暂停 自动 沿边 精扫 定点 返回 Remote control crevice tool Wall&ceiling brush Virtual wall Handheld belt Rolling brush cleaning tools Handheld mask Virtual wall battery Border tape Technique parameter(For D76) Function Parameter Voltage 12V Rated power 30W 0.2m/s speed Dust capacity 0.
Enjoy Smarter Life! 3.
3.
Enjoy Smarter Life! LCD and Control Panel mode 1. Power 7. Demo mode 13. Keep timing cleaning 19. Battery display 2. Model selection 8. Border cleaning mode 14. One-time timing cleaning 20. Tip for lacking dust box 3. On/Pause 9. Squelch cleaning mode 15. Time display 21. Tip for trapped 4. Pause status 10. Automatic cleaning mode 16. Appointment time setting 22. Tip for driving wheel suspending 5. Fixed point cleaning mode 11. Operation status 17. Time adjust button 6.
Tangle the power cord on the pothook and do not scatter it besides the block or hold it under the base, in case that robot would get impeded when it turns back. 0. 5 0. 5 m There should not be any object at least 1.5 meter in front of the charging m block. Besides, anything with strong reflector is not supposed to stay ahead of the infrared receiver. For example, ground glass, smooth ceramic vase and 1.5 m so on. Other wise, the machine shall not detect the charging block.
Enjoy Smarter Life! 5.Power On/Pause/Power Off Get power supply and power on ● Press the key on host and get power supply. There would be a short music tip and at the same time LCD lights for roughly 2 second and goes off. mode mode ● Then press key to start robot . mode mode Pause ● Press key, it can pause the operation of robot and keep it stay where it is. mode mode Tips: On the status of pause, you can reset the cleaning mode, then press key again, it will go back to work.
Tips : Put the robot on the charging block and keep it charging after finishing house cleaning. Do not keep the robot on pause status for long time, because under pause, the full charged battery can only last for around 20 hours. We suggest you to turn it off when you do not want it to work. 6.Mode Selection Status instruction : The meaning of often used three status here and hence mentioned is as follows: Working status: robot is operating by cleaning.
Enjoy Smarter Life! Under this status, robot helps to remove the corner of wall, table, sofa and bed where it is beyond the mode of automatic cleaning. The operation of this mode takes around 25 minutes and then robot goes back to charging block by itself. Fixed Point Cleaning Mode Route description: under this mode, robot runs from inside out shaping spiral and focuses on the certain point to clean for one time. The cleaning coverage is a round shape with diameter of 1.2 meter.
7.Automatically charging ● When it finishes cleaning or there is low battery, it would seek charger in same route as automatic cleaning.To make it easy for robot to search for charging block, you need to put the block back to the wall and make sure there is no obstacle within 1.5 meters ahead of the infrared receiver. Check carefully whether there is strong reflector in front of the charger, such as ground glass, smooth ceramic vase and so on. ？ ● It takes time for robot to seek the charger.
Enjoy Smarter Life! 9. Appointment Timing Appointment time setting 1. After power is on, keep press for around 3 seconds then on LCD is light and the number with time setting is flashing. First time setting mode mode Tips : 2. Set hour and minute via and , each time press will increase one hour or minute . While decrease one hour and minute for . 3. When you finish setting time, press again, and then go to second time setting .
Current time setting mode mode 1. After second time setting, and then go to the current time setting. The disappeared, and the number with time setting flashing. 2. Set hour and minute via and , each time press will increase one hour or minute. While decrease one hour and minute for . ,and then press to confirm. 3. Then go to the frequency setting. Tips : For example: Selection scope: hour is between 0 and 23, minute is between 0-59. Under normal circumstance, time display on LCD shows current time.
Enjoy Smarter Life! 10. Remote Control Batter y placement Tips: It applies two units of alkaline batteries AAA(7#) Please note the positive and negative when place the battery Change the battery when you notice it is in low battery and make sure you use the same kind of battery as mixture is forbidden. Take out the battery if you do not use remote control for long time to avoid electrolyte from leaking which may cause failure. Do not put the remote control in extremely hot or humid surroundings.
You can control cleaning mode, going back charging and direction within five meters through the function key on it. If the robot is under cleaning mode or going back charging, please press pause first and then can proceed direction control. During the direction control, robot is not able to operate cleaning. Make sure the power supply of remote control is on before you use it. When you use it, match the signal transmitter with signal receiver on the host.
Enjoy Smarter Life! Power: Press this key and virtual wall starts work which will prevent robot from entering the blocked region. Infrared receiver power Indicator: It is red when the power is on, and it shows virtual wall is ejecting invisible beam to prevent robot form entering the blocked region. Indicator transmitter Infrared transmitter: Ejecting invisible beam. Infrared receiver: receive invisible beam.
Paste the Border Tape on the floor after tearing off the white layer on one side. Rub the Border Tape with Border Enhancement Tool. Attention: 1. 2. 3. 4. 5. 6. Do not paste the Border Tape within a 1.5-meter radius vicinity of the Charging Station, or Deepoo will not be able to return for charging. Please make sure the area is dry, or the Border Tape might come off. When the magnetic field deteriorates, please use Border Enhancement Tool and rub on the Border Tape.
Enjoy Smarter Life! 15.Handheld vacuum cleaner ( For D76) By using the handheld vacuum cleaner , you can extend Deepoo’s function and cleaner your home more thoroughly. Assemble the handheld vacuum cleaner Attention: Press the “ Handheld vacuum cleaner releasing button “ on the back of Charging Station and take the handheld vacuum cleaner out by grabbing the handle. Do keep the air inlet hole up to avoid dust leakage and causing second pollution.
Adjusting telescopic length : push the button on the telescopic tube and adjust the tube to the desired length simultaneously and then release the adjusting button until you hear the Click sound which indicates the tube length has been fixed. Different accessories can be fixed onto the end of the telescopic tube for different use. Belt can be used for easy carrying of the handheld on your shoulder.
Enjoy Smarter Life! 2 31 41 51 61 71 Hold the handle of dust box and lift it to take out. In order to avoid dust leaking, lift the suction up when you take out dust box. Please mind your speed doing this step. Match the bottom with trash can and swing dust box gently. You can mildly beating it along the edge of the can to get the dust out. If you notice that there is too much dust on sponge filter, you can open the lock and take off the cover. Pour out the dust on sponge filter.
Sponge filter and dust box cleaning If you notice that there are too much dust on inside along dust box, you can put the box under running water to get rid of the dust. (make it dry under sunshine for 24 hours)Put it Open the lock at the bottom of dust box. back into the host after the Pour out the dust on sponge filter. box and sponge filter is completely dry. Main brush cleaning Tips: Clean the main brush after it has operated for 4 or 5 recycles. 1 11 Undo the screw fixed on the main brush.
Dust container cleaning Under normal situation , the dust container only need to be cleaned once per week (depending on you house situation). If you use the handheld vacuum cleaner separately , we suggest you to clean the dust container each time after your use. Press the “Handheld vacuum cleaner releasing button”on the back of Charging Station and take the handheld vacuum cleaner out by grabbing the handle. Do keep the air inlet hole up to avoid dust leakage and causing second pollution.
Enjoy Smarter Life! Tap the filtration assembly gently to get rid of the attached dust. Take the sponge out of the filtration assembly. If needed , the filtration assembly can be cleaned under tap-water. Don’t use brush to clean to avoid breakage. Attention: The filtration assembly should be fully dried before being reassembled into the units to use after each cleaning. Otherwise it will cause over-heat danger.
Enjoy Smarter Life! Side brush cleaning Side brush is a kind of easy wear part. We suggest you to check it every time it takes cleaning task. Please change it if necessary. Note： The host will alarm when the side brush tangles and it will show on LCD as . replace sidebrush Please remove the screws, and take out the side brush. Please replace the side brush when it is destroyed. Please push the new side brush into the correct position. Tight the screws.
Enjoy Smarter Life! Dust sensor cleaning The dust sensor is located at the front of dust entrance. It is able to detect the concentration of dust so that it can choose efficient mode to work. We suggest you to clean dust sensor once you clean dust box to improve work efficiency. 1. Turn off power. 2. Take out dust box and clean it. Replacing the batteries Your Robot is fitted with two 6V 2500mAah Ni-MH battery packs. The battery packs must be replaced together.
Enjoy Smarter Life! 17. Alarm function Note: The robot will stop working under following circumstance; there will be alarm and tip sound at the same time. What's more, LCD will have red light flashing. Please notice the tip on LCD. Icon Cause of failure 1. There is too much dust in dust box. 2. There is too much dust on dust sensor. 1. Dust box is not fixed into host. 2. Dust box is not fixed properly. 1. Main brush or driving wheel is tangled by hair or cloth. 2. Side brush is blocked. Solution 1.
18. Common Failure No. Problem Solution Turn off the power. 1. Check if there is dust on up-ground height 1 Robot keeps proceeding or moving backward once power is on. sensor, which cause robot to make wrong signal. Use half dry cloth to clean it. 2. Buffer collision is out of control. Put your hand at left, middle and right in turn to see if it can rebound by itself. Robot may fall in trouble when it is working.
Enjoy Smarter Life! 5 There is much noise when the robot works. Press the “ 6 ” D emo mode and the machine does not react Turn off the power supply, and then take out of dust box. After removing the garbage, overturn the robot. 1. Check whether the suction of main brush is blocked. 2. Examine and clean the main brush(at both ends) 3. Examine and clean the side brush. If the failure is still there after operating according to the above procedure, Please contact out after-sales service. 1.
cleaned for long time, as it is tangled with much hair and dust. 11 . Why does robot fail to start cleaning on appointment time? Answer: a.Confirm whether there is much remaining battery. Appointment timing is not applicable when robot is returning to charge after operating cleaning. b. Check if robot is under standby status. 12 . Why robot is not charging as it is put in the charger? The charging indicator does not light as well. Answer: a.
Enjoy Smarter Life! 22 . How does main brush avoid being tangled by power cord? Answer: Robot is probably get tangled by the wire scattered on the floor when it is operating. At that time, robot will try to turn back to get rid of it, and it will make alarm sound when it fails after trying several times. 23 . How can I stop the robot from operating on appointment time since I will be away from home for sometime? Answer: You can cancel appointment cleaning. 24 .
Enjoy Smarter Life!
