Robot Vacuum Cleaner D56 User Guide Downloaded From Vacuum-Manual.
Downloaded From Vacuum-Manual.
Thanks for purchasing patented Robot Vacuum Cleaner products. Hope you can enjoy it ! Thanks again for your choice! Downloaded From Vacuum-Manual.
Content 1. Safety Instruction....................... ... .....3 9. Day-to-Day Storage.......................... 16 User Guide............................ .. .... ..... ... 3 10. Maintenance.................... .... ............. 16 Power Supply for the Product......... .. ..... 3 Host Cleaning....................................16 The Spectrum of Product Use....... .. ....... 4 Dust Box Cleaning ..............................16 Notes before Cleaning.................. ... .....
Enjoy Smarter Life! 1.Safety Instruction War ning： Where there is a drop off in the cleaning area due to a step or stairs and they are not carpeted, you should operate the unit to see that the unit can detect the step without falling over the edge. It may become necessary to place a physical barrier at the edge to keep the unit from falling over the drop but make sure the physical barrier is high enough so that you or a family member will not trip on the barrier and cause themselves injury.
The Spectrum of the Product Use ● The robot is applicable to domestic sweeping, including wooden floor, rubber floor, ceramic tile, linoleum and medium or shorthaired carpet. However, it is inapplicable to longhaired carpet. ● It can not be used for the floor as below: ---- Have water on the surface (including flammable liquids), such as wet floor. ---- Inside toilet, shower room or other humid situation. ---- Staircase. ---- The room with furnace or flame.
Enjoy Smarter Life! Notes before Cleaning ● Take extra care of the robot when the first it works. Please remove the obstacles when it is beyond the robot. ● Make precautions to solve the problem which may make the cleaning in trouble, such as: ---- Keep the easily knock over objects in a safe place. ---- Permian the edge of the carpet. ---- The hanging tablecloth and curtain should not touch the ground. ---- The flammable object should be cut from the fire source.
● Take good care of the product and keep it beyond children and people who cannot judge danger nearby. Extra attention should be paid when the robot starts working. ● You should get the people inside the room know that the machine is working to avoid man-made damage like damaging. ● Do not take robot as toy. Carefully attention should be paid when child or pet is around. ● The plastic package may bring danger of asphyxia and is supposed to keep away from children.
Enjoy Smarter Life! 2.Cont ent Robot Vacuum Cleaner D56 User Guide User guide Charging block Host Side brush Roll brush clean-up gadget technique parameter The host Working voltage The charging block In-put voltage DC14.4V Rated power rated out-put voltage 30W Speed Noise 50Hz 0.7L rated power 30W ≤62dB rated out-put currency 0.7A Charging duration About 4~5 hours Duration upon full battery 60 minutes 60 minutes Max Coverage upon full battery 120-150 M Size DC17.
3.
Enjoy Smarter Life! LCD Display and Control Panel 19 20 18 17 21 22 1 16 2 mode 3 15 4 14 9 11 13 10 7 8 12 5 6 1. Power 7. Border cleaning mode 13. One-time timing cleaning 19. Tip for cleaning dust box 2. Model selection 8. Intensive cleaning mode 14. Time display 20. Tip for lacking dust box 3. On/Pause 9. Automatic cleaning mode 15. Time cleaning status 21. Tip for trapped 4. Pause status 10. Operation status 16. Appointment time setting 22.
Tangle the power cord and do not scatter it besides the block in case that robot would get impeded when it turns back . 0. 5 0. 5 There should not be any object at least 1.5 meter in front of the charging m m block. Besides, anything with strong reflector is not supposed to stay ahead of the infrared receiver. For example, ground glass, smooth ceramic vase and so 1.5 m on. Otherwise, the machine shall not detect the charging block.
Enjoy Smarter Life! 5.Power On/ Pause/ Power Off Get power supply and power on ● Turn on the power switch on the bottom firstly. ● Get power supply and press the button on host. There would be a short music tip and at the same time the battery indicator lights. mode ● Press button to start the robot mode Pause ● Press key, it can pause the operation of robot and keep it stay where it is. mode Tips: On the status of pause, you can reset the cleaning mode, then press button to restart the robot.
Tips : Put the robot on the charging block and keep it charging after finishing house cleaning. 10 Do not keep the robot on pause status for long time, because the full charged battery could only last for around 20 hours. We suggest you to turn it off when you do not want it to work. 6.Mode Selection Status instruction : The details of three statuses mentioned as bellowing: Working status: robot is doing cleaning job .
Enjoy Smarter Life! Border Cleaning Mode Route description: under this mode, once the robot detects hard objects (like wall), it will run along it to clean until it meets obstacle and change the former route. Under this mode, robot helps to clean the corner of wall, table, sofa and bed where it is beyond the mode of automatic cleaning. The operation of this mode takes around 25 minutes and then robot goes back charging by itself.
7 .Automatically charging ● When robot detects the low battery, it will go back charging automatically. ？ ● To make it easy for robot to search for charging block, you need to put the block back to the wall and make sure there is no obstacle within 1.5 meters ahead of the infrared receiver. Check carefully whether there is strong reflector in front of the charger, such as ground glass, smooth ceramic vase and so on. ● It takes time for robot to seek the charger.
Enjoy Smarter Life! Set cur rent time mode 1. After appointment time setting, the label high light, and the number with time setting is flashing. 2. Set hour and minute via and , each time press will increase one hour or minute, while decrease one hour and minute for . mode 3. Press setting. again, and then go to frequency For example: Tips : Selection scope: hour is between 0 and 23, minute is between 0-59. Under normal circumstance, time display on LCD shows current time.
9.Day-to-day storage You should keep robot stay at charger even though it finishes charging, because it will change to small currency to supplement charging. Charge the robot until full battery and put it back to the package if you do not need to use it for ling time. Keep the package in dry surroundings to avoid sunshine or humidity. 10.Maintenance Host Cleaning Turn off the power before cleaning the host. Draw out the plug of charger before cleaning the block.
Enjoy Smarter Life! 21 Hold the handle of dust box and lift it to 31 take out. In order to avoid dust leaking, lift the suction up when you take out dust box. Please mind your speed doing this step. 41 Match the bottom with trash can and swing 51 If there is too much dust on sponge filter, you can dust box gently. You can open the lock and take off mildly beating it along the cover. the edge of the can to get the dust out. 61 Pour out the dust on sponge filter.
Sponge Filter Replacement 1. Open the cover of the Deebot, take out the dust box. 2. Push aside the lock catch of the dust box ,then open the dust box and clean it. 3. Extract the axle of the dust box’s cover. 4. Replace the sponge filter and fix the cover ,then put it back into Deebot. Main Brush Cleaning Tips: Clean the main brush after it has operated for 4 or 5 recycles. 1 11 Undo the screw fixed on the main brush. 2 Take off the frame of main brush.
Enjoy Smarter Life! Side Brush Cleaning Side brush is a kind of easy wear part. We suggest you to check it every time it takes cleaning task. Please change it if necessary. Note： The host will alarm when the side brush tangles and the Replace Sidebrush lights. Please replace the side brush when it is destroyed. Please remove the screws, and take out the side brush. Please push the new side brush into the correct position. Tight the screws.
Dust Sensor Cleaning The dust sensor is located at the front of dust entrance. It is able to detect the concentration of dust so that it can choose efficient mode to work. We suggest you to clean dust sensor once you clean dust box to improve work efficiency. 1. Turn off power. 2. Take out dust box and clean it. 3.Wipe the dust sensor with dry cotton cloth. 1 1 .Alarm function Note: The robot will stop working and be alarm and tip sound at the same time. Please do as bellowing to solve the problem.
Enjoy Smarter Life! 12.Common Failure No. Problem Solution Turn off the power. 1.Check if there is dust on up-ground height 1 Robot keeps proceeding or moving backward once power is on. sensor, which cause robot to make wrong signal. Use half dry cloth to clean it. 2.Buffer collision is out of control. Put your hand at left, middle and right in turn to see if it can rebound by itself. Robot may fall in trouble when it is working.
Turn off the power supply, and then take out of dust box. After removing the garbage, overturn the robot. 5 There is much noise when the robot works. 1. Check whether the suction of main brush is blocked. 2. Examine and clean the main brush. 3. Examine and clean the side brush. If the failure is still there after operating according to the above procedure, Please contact our after-sales service. 13.Other Problems 1.
Enjoy Smarter Life! 9. Why does robot fail to start cleaning on appointment time? Answer: a.Confirm whether there is much remaining battery. Appointment timing is not applicable when robot is returning to charge after operating cleaning. b. Check if robot is under standby status. 10 . Why robot is not charging as it is put in the charger? The charging indicator does not light as well. Answer: a.
21 . What should do if robot sucked liquid? Answer: a. Turn off the power and take out dust box, then empty it and wipe it dry. b. Draw out the sponge filter and wipe it dry. c. Take out main brush and clean it, then use day cloth to wipe the brush and its interior. Wait until the brush is day and place it back. d. Let the product dry by itself for at least 12hours(make sure circuit board is dry and then get power on) If the procedures above still do not make it work, please contact our after-sales service.
Downloaded From Vacuum-Manual.
Enjoy smar ter life! D56-000IM2011 01 Downloaded From Vacuum-Manual.
