EN Instruction Manual
Congratulations on the purchase of your ECOVACS Robotics DEEBOT! We hope it brings you many years of satisfaction. We trust the purchase of your new robot will help keep your home clean and provide you more quality time to do other things. Live Smart. Enjoy Life. Should you encounter situations that have not been properly addressed in this Instruction Manual, please contact our Customer Service Center where a technician can address your specific problem or question.
Contents 1. Important Safety Instructions.......................................................................2 2. Package Contents and Technical Specifications.......................................4 2.1 Package Contents.....................................................................................4 2.2 Specifications............................................................................................4 2.3 Product Diagram.......................................................................
1. Important Safety Instructions When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE. SAVE THESE INSTRUCTIONS 1. This Appliance is not intended to be used by children under 8 or anyone lacking knowledge on proper use. Supervision may be necessary. Do not allow children to sit on or play with the Appliance. 2. Clear the area to be cleaned.
1. Important Safety Instructions 22. Turn OFF the power switch before cleaning or maintaining the Appliance. 23. The plug must be removed from the receptacle before cleaning or maintaining the Charging Dock. 24. Remove the Appliance from the Charging Dock, and turn OFF the power switch to the Appliance before removing the battery for disposal of the Appliance. 25. The battery must be removed and discarded according to local laws and regulations before disposal of the Appliance. 26.
2. Package Contents and Technical Specifications 2.1 Package Contents Instruction Manual EN Robot Charging Dock (2) Side Brushes Multi-Function Cleaning Tool Instruction Manual Remote Control with Batteries 2.2 Specifications Model Working Voltage D63S 12V DC Charging Dock Model Rated Input Voltage Rated Output Current Remote Control Model Battery Rated Power 30W CH1118D 100-240V AC Rated Output Voltage 14.5V DC 0.
2. Package Contents and Technical Specifications 2.3 Product Diagram Robot 8 9 1 2 3 4 10 11 12 18 17 5 6 13 14 15 7 16 1. Status Light Indicators 2. Top Cover 3. Control Panel 4. Control Panel Screen 5. Infrared Receiver for Remote Control 6. Anti-Collision Sensors 7. Charging Contacts 8. Side Brush 9. Anti-Drop Sensors Control Panel 1 7 8 1. Battery Display 2. Return to Charger Mode Indicator 3. Alarm Indicator 4. AUTO Cleaning Mode Indicator 5. Intelligent Scheduling Indicator 2 10.
2. Package Contents and Technical Specifications Charging Dock 3 1 4 2 6 5 1. Lock/Release Button 2. Charging Dock Pins 3. Charging Dock Top Lid 4. Infrared Signal Generator 5. Anti-Slip Strips 6. Charging Dock Base Remote Control 8 5 1 6 7 2 3 4 1. Pause Button 2. AUTO Mode Button 3. Spot Cleaning Mode Button 4. Edge Cleaning Mode Button 5. Direction Control Buttons 6. Intensive Cleaning Mode Button 7. Return to Charger Mode Button 8. Infrared Emitter Dust Bin 1 4 5 6 2 3 1. Dust Bin Handle 2.
3. Operating and Programming 3.1 Notes Before Cleaning Before Operating DEEBOT, take a few moments to survey the area to be cleaned and remove any obstacles. Remove power cords and small objects from the floor that could entangle the product. The product is not suitable for use on long-pile carpet. Before using the product near a long-pile area rug or on a short-pile area rug with tasseled edges, please fold area rug edges under themselves. Please be aware that the robot needs at least a 9cm (3.
3. Operating and Programming 3.2 Quick Start 1 Charging Dock Placement Assemble Charging Dock: Insert the Charging Dock Top Lid into the slot on the Charging Dock Base. Slide the Lock/Release button on the back of the Charging Dock to the left to lock the Top Lid in place. Placement: Place the Charging Dock on a level floor surface against the wall with the base perpendicular to the ground. Keep the immediate area 1.5m (5') in front of the charger and 0.5m (1.
3. Operating and Programming 4 Charge DEEBOT 6 Place DEEBOT 6 on the Charging Dock making sure the Charging Contacts on DEEBOT 6 and the Charging Dock Pins make a connection. * Charge DEEBOT 6 for at least 12 hours before the first use. * The Status Light Indicators on the top of the robot and the Battery Display on the robot’s Control Panel Screen blink when DEEBOT 6 is charging and go off when DEEBOT 6 is fully charged. 5 Start Press the AUTO Mode Button on the robot or on the Remote Control.
3. Operating and Programming 3.3 Cleaning Mode Selection DEEBOT 6 has several Cleaning Modes for you to choose from to effectively clean different floors. Cleaning Modes are selected using the robot’s Control Panel Buttons or using the Remote Control. * Pause DEEBOT 6 before switching Cleaning Modes. AUTO Cleaning Mode This is the most commonly used mode. In AUTO Cleaning Mode, DEEBOT 6 cleans in a straight line and changes direction when it meets an obstacle.
3. Operating and Programming Spot Cleaning Mode Edge Cleaning Mode This mode is applicable for an area of highly concentrated dirt or dust. In Spot Cleaning Mode, DEEBOT 6 focuses on a specific area to clean. This mode is good for cleaning the edges and corners of a room. In Edge Cleaning Mode, DEEBOT 6 cleans along a border (e.g. wall). * These modes can only be selected using the Remote Control.
3. Operating and Programming 3.4 Intelligent Scheduling DEEBOT 6 has an Intelligent Scheduling function. DEEBOT 6 can be scheduled to clean once per day at the same time, even if nobody is at home. Set Intelligent Scheduling Press on DEEBOT 6 to set the current time as the scheduled cleaning time. Intelligent Scheduling is set successfully when indicator on the robot’s Control Panel Screen illuminates.
4. Maintenance * Before performing cleaning and maintenance on DEEBOT 6, turn the Bottom Power Switch to the OFF position and unplug the Charging Dock. 4.1 Dust Bin and Filters Open DEEBOT 6’s Top Cover and remove the Dust Bin. Open the Dust Bin Cover and empty the Dust Bin. Remove the filters. Pat the High Efficiency Filter clean. Do not rinse the High Efficiency Filter under water. Rinse the Dust Bin, Sponge Filter and Filter Net under running water.
4. Maintenance 4.2 Main Brush and Side Brush * A Multi-Function Cleaning Tool is provided for easy maintenance. Handle with care, this cleaning tool has sharp edges. Cleaning the Main Brush Unscrew the Main Brush Screw and remove the Main Brush. Use the Multi-Function Cleaning Tool to cut off and remove any hair tangled around the Main Brush. Cleaning the Side Brush Remove the Side Brush. Wipe the Side Brush and its slot with a dry cloth.
4. Maintenance 4.3 Other Components Clean the Universal Wheel by removing any hair tangled around the Universal Wheel. Wipe the Anti-Drop Sensors with the brush or the felt side of the Multi-Function Cleaning Tool to maintain their effectiveness. Wipe the Dust Sensors with the brush or the felt side of the Multi-Function Cleaning Tool to maintain their effectiveness. Wipe the Charging Contacts and Charging Dock Pins clean with a dry cloth.
5. Troubleshooting Please use this chart to troubleshoot common problems using DEEBOT 6. NO. 1 2 3 4 16 EN Malfunction DEEBOT 6 will not charge. DEEBOT 6 gets into trouble while working and stops. DEEBOT 6 returns to the Charging Dock before it finishes cleaning. DEEBOT 6 will not clean automatically at scheduled time. Possible Causes Solutions The Bottom Power Switch on the bottom of DEEBOT 6 is not turned ON. Turn the Bottom Power Switch to the ON position.
5. Troubleshooting NO. 5 Malfunction Remote Control failure (effective control range of Remote Control is 5m (1.6')). Possible Causes Solutions The batteries in the Remote Control need to be replaced. Replace with new batteries making sure they are installed correctly. The Bottom Power Switch is turned OFF, or DEEBOT 6’s battery is low. Make sure DEEBOT 6’s Bottom Power Switch is ON and fully charged.
DEEBOT 6-MS-IM2014R00
