SERIES Smart Vacuum Cleaner Instruction Manual Manual De Uso Mode D’emploi *Actual product may differ from illustration.
EN CONTENTS Important Safety Instructions............................................................... 2 Overview................................................................................................ 5 Accessories............................................................................................ 7 Assembly ............................................................................................... 9 Operation ..........................................................................
Important Safety Instructions EN SAVE THESE INSTRUCTIONS Household use only. When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE). Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. WARNING – To reduce the risk of fire, electric shock, or injury: 1.
Only For NA: FCC Supplier’s Declaration of Conformity 5JOFDP 4NBSU 7BDVVN $MFBOFS 163& 0/& 4 7（VS12200AUS ,VS12220AUS, VS12230AUS) 2.PURE ONE S12V PLUS (VS12210AUS,VS12240AUS,VS12250AUS） This appliance complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This appliance may not cause harmful interference, and (2) this appliance must accept any interference received, including interference that may cause undesired operation. TINECO INTELLIGENT, INC.
WWW.TINECO.COM 1-855-292-8864 EN Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital appliance, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Overview EN S12V A B C D E F G H I J K A. Magnetic attachment zone F. Trigger lock B. Dust empty release button G. Dustbin release button C. Dustbin H. Trigger D. MAX/AUTO I. HEPA release button E. WiFi reset button J. Battery indicator light (Remove the dustbin to access) K.
EN S12V Plus A B C D E F G H I J K L M A. Magnetic attachment zone G. MAX/AUTO B. Mute button H. Trigger lock C. Dust empty release button I. Dustbin release button D. Dustbin J. Trigger E. Built-in bluetooth speaker K. HEPA release button F. WiFi reset button L. Battery indicator light (Remove the dustbin to access) M.
Accessories Note: • Test an accessory on a small, inconspicuous area before use on sensitive surfaces. • The “Product Components” page shows which accessories are included with your purchase. • As shown below, there are many components compatible with this model. If you require more accessories, please visit the Tineco Official Site. www.tineco.com Products Parts and Accessories Buy Now EN BUY ONLINE Full-size LED multi-tasker power brush Ideal for both hard floors and carpets.
Flexible long crevice tool Easy to bend, easy to reach tight spots. Suitable for cleaning dust behind and beneath furniture, around refrigerators, and many other tight gaps. Full-size LED soft-roller power brush EN Perfect for hard floors, especially sensitive wood floor. Picks up coarse and fine dirt at the same time. Multi-angle folding tube An articulated joint makes it adjustable to allow for flexibility when cleaning from high to low.
Assembly EN Tube Installation Insert tube. Press the release button to remove the tube. Brush Installation Insert the power brush. Press the release button to remove the power brush.
Dustbin Installation EN Ύ To clean the dustbin more thoroughly, press the dustbin release button to fully detach from the appliance. When re-attaching the dustbin, hold on an angle and slot the top of the dustbin into the hook on the main body. Push upwards until the hook is fixed into the slot on the dustbin and then it clicks into place. Battery Installation Press the battery release button, and remove the battery. To replace, slide the battery into the slot at the base of the main body.
Operation Preparing for Use Note: EN • Before the first use, please charge the appliance (see “Charging the Battery”) for 3-4 hours in an area where the ambient temperature is between 39.2°F (4°C) and 104°F (40°C). • Select an accessory and attach it to the appliance before use (see “Accessories”). Pull the trigger lock to hold the trigger for continuous power mode. MAX AUTO Pull the trigger to activate the suction. MAX AUTO The appliance will start in AUTO mode by default.
EN • Determine the best wall location for mounting the dock. Choose a location close to an electrical outlet and measure the length of the power cord to be sure that it will reach. Warning: • Ensure the wall surrounding the mounting area is free of gas or water pipes and electrical cables and wires. • To avoid the dock falling, ensure it is firmly installed. Assemble the two bracket components, with a “click” to signify correct assembly.
Adhesive Magnet 1 2 AUTO EN MAX With a dustless cloth, wipe the main body and the back of your phone to remove all dust. Remove the cover from the adhesive surface and place the magnet on the back of the phone. Wait 10 minutes before using. 3 With the magnet attached, place the phone on the magnetic attachment zone in order to secure on the main body. Note: • The ideal ambient temperature when attaching the magnet is 59 °F (15°C) - 100.4 °F (38 °C).
Discover More Work with Alexa EN Connect your devices to Alexa and you can give voice commands to check work status, obtain a cleaning report, etc. Voice Prompt (for PURE ONE S12V Plus) The appliance can report the work status in real time.
NFC Reader EN • The appliance is equipped with NFC technology, enabling for simpler connection to the Tineco app. iOS Ύ Android Ώ ΐ 1. Enable NFC functionality and place the phone within the reading area. 2. Follow the prompts on your phone screen to go to the app download page; no need to search in the App Store. 3. After the app is downloaded, the login page will automatically appear. 4. After login, the Tineco device list page will open.
App Function Introduction Battery Battery level in real time. Cleaning Performance 0 /0 dust Cleaning report min Displays the dust amount, working hours and working status. EN Total dust: 0 dust/0 min Suction adjustment When in manual mode, swipe the phone screen to adjust suction power. Filter status reminder Records the severity of the dirty filter and provides a cleaning reminder as required. Contact us You can contact the Customer Service about any problems during the working hours.
Cleaning Mode Selection AUTO mode • In AUTO mode, the suction power will change in real time according to the amount of dust detected. Start in two ways: The default setting on startup is AUTO. The appliance then takes 3 seconds to initially detect blockages or dust. If no dust is detected, power is reduced to conserve energy. Ύ MAX AUTO In Max mode, press MAX/AUTO button or click AUTO in the App to enter the AUTO mode. MAX mode MAX AUTO In AUTO mode, press the MAX/AUTO button to switch to MAX mode.
