EN Instruction Manual
Congratulations on the purchase of your ECOVACS ROBOTICS DEEBOT! We hope it brings you many years of satisfaction. We trust the purchase of your new robot will help keep your home clean and provide you more quality time to do other things. Live Smart. Enjoy Life. Should you encounter situations that have not been properly addressed in this Instruction Manual, please contact our Customer Service Center where a technician can address your specific problem or question.
Contents 1. Important Safety Instructions ���������������������������������������������������������������������� 2 2. Package Contents and Technical Specifications �������������������������������������� 4 2.1 Package Contents ������������������������������������������������������������������������������������ 4 2.2 Specifications ������������������������������������������������������������������������������������������� 4 2.
1. Important Safety Instructions When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE. SAVE THESE INSTRUCTIONS 1. This Appliance is not intended to be used by children under 8 or anyone lacking knowledge on proper use. Supervision may be necessary. Do not allow children to sit on or play with the Appliance. 2. Clear the area to be cleaned.
1. Important Safety Instructions 22. Turn OFF the power switch before cleaning or maintaining the Appliance. 23. The plug must be removed from the receptacle before cleaning or maintaining the Charging Dock. 24. Remove the Appliance from the Charging Dock, and turn OFF the power switch to the Appliance before removing the battery for disposal of the Appliance. 25. The battery must be removed and discarded according to local laws and regulations before disposal of the Appliance. 26.
2. Package Contents and Technical Specifications 2.1 Package Contents Robot Charging Dock Remote Control with Button Cell Battery Instruction Manual (4) Side Brushes Main Brush Option (pre-installed) Direct Suction Option (2) Advanced Wet/Dry Cleaning Cloths Advanced Wet/Dry Reservoir Replacement High Efficiency Filter+ Sponge Filter Measuring Cup Reservoir Cleaning Solution 2.
2. Package Contents and Technical Specifications 2.3 Product Diagram Robot 4 1 2 17 15 14 16 5 10 6 11 7 8 9 12 3 13 1. Top Cover 2. Control Panel 3. Anti-Collision Sensors 4. Anti-Drop Sensors 5. Charging Contacts 6. Side Brushes 7. Main Brush Option 8. Driving Wheels 9. Bottom Power Switch 10. Universal Wheel 11. Battery Cover 12. Advanced Wet/Dry Reservoir Slots 13. Infrared Receiver for Remote Control 14. Reset Button (For Customer Service Only) 15. Dust Bin 16. Main Brush Cover 17.
2. Package Contents and Technical Specifications Remote Control 8 1 1. AUTO Mode Button 2 2. Direction Control Buttons 3 3. START/PAUSE Button 6 4 5 7 4. Return to Charger Mode Button 5. Single Room Mode Button 6. Edge Cleaning Mode Button 7. Network Setup Button 8. Infrared Emitter Dust Bin 1 1. Dust Bin Handle 2. Dust Bin Lock 2 3 4 5 6 3. Filter Net 4. Sponge Filter 5. High Efficiency Filter 6. Dust Bin Cover Advanced Wet/Dry Reservoir 1 2 3 6 EN 1. Advanced Wet/Dry Cleaning Cloth 2.
3. Operating and Programming 3.1 Notes Before Cleaning Before operating DEEBOT, take a few moments to survey the area to be cleaned and remove any obstacles. Remove power cords and small objects from the floor that could entangle the product. The product is not suitable for use on long-pile carpet. Before using the product near an area rug or on a short-pile area rug with tasseled edges, please fold area rug edges under themselves. Please be aware that the robot needs at least an 8 cm (3.
3. Operating and Programming When DEEBOT is cleaning using Programmed Cleaning Pattern, please do not stand in narrow spaces, such as hallways, or DEEBOT may fail to identify the area to be cleaned. 3.2 Quick Start * Remove the Bumper Rail protection sponge on the DEEBOT before the first use. 1 Charging Dock Placement Place the Charging Dock on a level floor surface against the wall with the base perpendicular to the ground. Keep the immediate area 1.5m (5') in front of the charger and 0.5m (1.
3. Operating and Programming 2 Install Side Brushes Attach Side Brushes to the bottom of DEEBOT by pressing a brush into each slot with the matching color until it clicks. 3 Power ON Turn the robot’s Bottom Power Switch to the ON position. “I”=power ON; “O”=power OFF. Press and hold AUTO Mode Button on the robot. DEEBOT is powered ON when the AUTO Mode Button glows a continuous BLUE. ON * When DEEBOT is not cleaning, it is suggested to keep it powered ON and charging instead of powered OFF.
3. Operating and Programming 5 Start Press the AUTO Mode Button on DEEBOT or on the Remote Control. DEEBOT starts to work immediately in AUTO Cleaning Mode using the default Random Cleaning Pattern. * To choose another Cleaning Mode or Cleaning Pattern, please refer to section 3.3 Cleaning Pattern and Cleaning Mode Selection for details. 6 Pause Pause DEEBOT by pressing the AUTO Mode Button on DEEBOT or the START/PAUSE Button on the Remote Control.
3. Operating and Programming 3.3 Cleaning Pattern and Cleaning Mode Selection DEEBOT has 2 Cleaning Patterns and several Cleaning Modes to choose from to effectively clean different floors. Cleaning Patterns and Cleaning Modes are selected using the Remote Control or the ECOVACS App. For more information on the ECOVACS App, see the separate ECOVACS App leaflet. Set Cleaning Pattern Set the cleaning pattern based on floor type.
3. Operating and Programming Press and hold the AUTO Mode Button on the Remote Control for 3 seconds. Programmed Cleaning Pattern is set when DEEBOT emits one beep. To switch back to Random Cleaning Pattern, press and hold the AUTO Mode Button on the Remote Control for 3 seconds. Random Cleaning Pattern is set when DEEBOT emits two beeps. 3Ƞ Cleaning Patterns can also be set using the ECOVACS App. DEEBOT uses the set Cleaning Pattern when cleaning in AUTO Cleaning Mode and Single Room Cleaning Mode.
3. Operating and Programming 2 Single Room Mode This mode is used when DEEBOT only needs to clean a single room with a maximum size of 30 m2 (323 sq ft). To start Single Room Cleaning Mode, press the Single Mode Button on the Remote Control or on the App main screen. * Single Room Cleaning Mode cleans using the set Cleaning Pattern. Random Cleaning Pattern is best for carpet. Programmed Cleaning Pattern is best for bare floors. * The room must be contained for Single Room Mode to function properly.
3. Operating and Programming 4 Edge Cleaning Mode This mode is good for cleaning the edges and corners of a room. To start Edge Cleaning Mode, press the Edge Cleaning Mode Button on the Remote control or on the App main screen. In Edge Cleaning Mode, DEEBOT cleans along a border (e.g. wall), and returns to the Charging Dock when it completes cleaning. * Use the App to increase the suction power of any Cleaning Mode already in process. Press in the App for MAX suction power.
3. Operating and Programming 3.4 Programming the Robot DEEBOT has an Intelligent Scheduling and a Time Scheduling function to schedule cleaning times. DEEBOT can be programmed to automatically clean once per day at the same time with Intelligent Scheduling using the robot’s Control Panel. DEEBOT can also be programmed weekly to clean up to two times per day at specific times with Time Scheduling using the App. * All scheduled cleanings are performed in AUTO Cleaning Mode using the Random Cleaning Pattern.
3. Operating and Programming Time Scheduling Set Time Scheduling DEEBOT can be programmed weekly to clean multiple times per day at specific times using the ECOVACS App. Open the ECOVACS App. Press “ ” in top right corner on the App's main screen. Set new scheduled cleanings and cancel existing scheduled cleanings in "Time Scheduling." * Please allow at least 7 hours between scheduled cleaning times. 3.5 Choosing a Suction Option The robot has 2 interchangeable suction options for your convenience.
3. Operating and Programming Install the Main Brush Option Turn the robot over. Push both buttons on the Direct Suction Option and remove Direct Suction Option. Insert the Main Brush into the bottom of the robot. Line up the Main Brush Cover tabs with the slots on the bottom of the robot. Press until the component clicks into place. 3.
3. Operating and Programming 2 Add Water to the Advanced Wet/Dry Reservoir * Before adding water to the Advanced Wet/Dry Reservoir remove the Advanced Wet/Dry Reservoir from the bottom of the robot. Fill the provided Measuring Cup with water. Open the Water Inlet lid on the Advanced Wet/Dry Reservoir and slowly pour water from the Measuring Cup into the Reservoir. Close the Water Inlet lid. Attach the Advanced Wet/Dry Reservoir to the bottom of the robot.
3. Operating and Programming 3 Start Select the desired Cleaning Mode. DEEBOT sweeps. lifts, vacuums, mops and dries in the selected mode. * It is suggested to select Single Room Mode when using the optional Advanced Wet/Dry Mopping System for maximum efficiency. * To mop another room, move DEEBOT to the room to be cleaned, refill the Water Reservoir/ change the Cleaning Cloth as needed and restart.
3. Operating and Programming 3.7 Alarm Indicator and Sounds If DEEBOT detects a problem and needs your assistance, it emits alarm beeps and the AUTO Mode Button flashes RED. Alarm Sound Problems Solution One Beep Driving Wheel Malfunction Check Driving Wheels for tangled hair or debris and clean as described in section 4 Maintenance. Driving Wheel Malfunction Turn over the robot. Press Driving Wheels to check for a clicking sound. If they do not click, please contact Customer Service.
4. Maintenance Before performing cleaning and maintenance, power OFF DEEBOT and unplug the Charging Dock. 4.1 Dust Bin and Filters Cleaning the Dust Bin and Filters Open the robot’s Top Cover and remove the Dust Bin. Open the Dust Bin Lock and empty the Dust Bin. Remove the filters. Pat the High Efficiency Filter clean. Do not rinse the High Efficiency Filter under water. Rinse the Sponge Filter, Dust Bin and Filter Net under running water. Dry the Dust Bin and filters completely before reinstalling.
4. Maintenance 4.2 Advanced Wet/Dry Cleaning Cloth an Advanced Wet/Dry Reservoir Cleaning the Advanced Wet/Dry Cleaning Cloth If the mopping system was used, remove the Advanced Wet/Dry Reservoir from the bottom of DEEBOT and remove the Advanced Wet/Dry Cleaning Cloth. Empty any remaining water from the Reservoir. Wash the Cleaning Cloth by hand, and lay flat to dry. Cleaning the Advanced Wet/Dry Reservoir If the mopping system was used, remove the Advanced Wet/Dry Reservoir from the bottom of DEEBOT.
4. Maintenance 4.3 Main Brush, Direct Suction Option and Side Brushes * A Multi-Function Cleaning Tool is provided for easy maintenance. Handle with care, this cleaning tool has sharp edges. Cleaning the Main Brush Turn the robot over. Push both buttons on the Main Brush Option and remove the Main Brush cover. Remove the Main Brush. Use the Multi-Function Cleaning Tool to cut off and remove any hair tangled around the Main Brush.
4. Maintenance 4.4 Other Components Use the Multi-Function Cleaning Tool to cut off and remove any hair tangled around the Universal Wheel. Wipe the Anti-Drop Sensors with the brush or felt side of the Multi-Function Cleaning Tool to maintain their effectiveness. Wipe the robot’s Charging Contacts and Charging Docks Pins with the brush of the Multi-Function Cleaning Tool or with a dry cloth to maintain their effectiveness.
5. Troubleshooting Please use this chart to troubleshoot common problems using DEEBOT. No. 1 2 3 Malfunction DEEBOT will not charge. DEEBOT will not return to the Charging Dock. DEEBOT gets into trouble while working and stops. Possible Causes Solutions DEEBOT is not powered ON. Move the robot’s Bottom Power Switch to the ON position. DEEBOT has not made a connection with the Charging Dock. Be sure that the robot’s Charging Contacts have made a connection with the Charging Dock Pins.
5. Troubleshooting No. 4 5 6 26 EN Malfunction DEEBOT returns to the Charging Dock before it finishes cleaning. DEEBOT will not clean automatically at scheduled time. DEEBOT misses the spots to be cleaned. Possible Causes Solutions When battery power gets low, DEEBOT automatically switches to Return to Charger Mode and returns to the Charging Dock to recharge itself. This is normal. No solution necessary.
5. Troubleshooting No. 7 Malfunction Remote Control failure (Effective control change of the Remote Control is 5m (16’). Possible Causes Solutions The battery in the Remote Control need to be replaced. Replace with a new battery making sure it is installed correctly. DEEBOT is powered OFF or the robot’s battery is low. Make sure DEEBOT is powered ON and fully charged.
DM88-000-IM2016R00
